Transition from random packing to stable state in a continuously avalanching granular flow

We investigate the transition evolution from the initial state with the random packing of the particles to the stable state in which successive avalanches exhibit consistent characteristics under the slumping regime. It is found that there exist three distinct stages in the transition evolution, considering the change of the volume fraction. The coordination number is almost unchanged during the transition evolution, which indicates the particle contact form is consistent in the three stages. The pause phenomena are discovered in some avalanches, and the probability of pause occurrence increases continuously in the three consecutive stages. We also explore the distribution of particles in the passive layer at the stable state. The particles in the middle region of the passive layer have the closest packing status, and the deeper the region is located, the later it reaches the stable state.     

Experimental investigation of unconfined spherical and cylindrical flame propagation in hydrogen-air mixtures

This paper presents results of experimental investigations on spherical and cylindrical flame propagation in pre-mixed H₂/air-mixtures in unconfined and semi-confined geometries. The experiments were performed in a facility consisting of two transparent solid walls with 1 m² area and four weak side walls made from thin plastic film. The gap size between the solid walls was varied stepwise from thin layer geometry (6 mm) to cube geometry (1 m). A wide range of H₂/air-mixtures with volumetric hydrogen concentrations from 10% to 45% H₂ was ignited between the transparent solid walls. The propagating flame front and its structure was observed with a large scale high speed shadow system. Results of spherical and cylindrical flame propagation up to a radius of 0.5 m were analyzed. The presented spherical burning velocity model is used to discuss the self-acceleration phenomena in unconfined and unobstructed pre-mixed H₂/air flames.     

湿硫化氢环境下的球罐腐蚀状况分析

在湿硫化氢环境下 ,尤其储存介质中的硫化氢含量超标时 ,很容易对储存容器壳体 (含焊缝和母材 )造成硫化氢应力腐蚀或氢鼓包。作者较仔细分析了 1 0 0 0m3 丙烯球罐产生硫化氢应力腐蚀开裂和40 0m3 LPG球罐产生氢鼓包的原因。提出了此类设备在设计选材、设备制造、施工安装和使用维护等环节应注意的问题。     

Pressure Behavior for Spherical Flow in a Reservoir of Non-Newtonian Power-Law Fluids

The pressure variations during polymer flooding of oil reservoirs for oil recovery projects can be used to analyze the flow in the reservoir which is especially useful for the partially perforated reservoirs. This paper presents a relationship between the viscosity and the shear rate which is similar to forms developed for radial flow (Odeh, A. S., Yang, H. T. ([1979]). SPEJ. AIME (Jun.) 155). The power-law viscosity model is used to give the variation of the fluid viscosity with the spherical radius for a mathematical model of unsteady spherical flow for non-Newtonian fluids with wellbore storage and skin. An analytical solution for the wellbore pressure responses derived in Laplace space is used to analyze the behavior characteristics at early and later times to interpret the well-test parameters. The pressure variations are similar to those for a Newtonian fluid at the early times, but at later times, the variation of the viscosity with the power-law exponent is important, so the pressure response differs from that for a Newtonian fluid. The solution has significance for interpreting well test parameters for non-Newtonian spherical flow.     

模糊C-球壳聚类算法及其在血液细胞图像中的应用

文章从经典的模糊C均值算法开始通过改变其中相似性的度量形式，介绍了一种模糊C球壳聚类（FCSS）算法。在将该算法应用于细胞显微图像半径统计时，采用基于形态学的图像预处理措施，可以获得FCSS算法中有关原型模式的知识，加快收敛速度并避免随机初始化造成的局部极小问题。     

凸非球面补偿检验的工艺球面分析解

本文从三级像差理论出发,推导了几种工艺球面检验凸二次曲面的计算公式。根据这些公式计算结果,进行了光路追迹,给出了这些公式对凸二次曲面的补偿范围;并讨论了几种特殊情况下的平面解。     

压力容器标准椭圆封头拼接焊缝射线探伤工艺的改进措施

为了满足生产需要对椭圆封头拼接焊缝射线探伤工艺进行改进。并取得了满意效果。     

Biomimetic synthesis of spherical nano-hydroxyapatite in the presence of polyethylene glycol

Spherical nano-hydroxyapatite (nano-HA) was synthesized successfully by a biomimetic method using Ca(NO₃)₂·4H₂O and (NH₄)₃PO₄·3H₂O as reagents in the presence of polyethylene glycol (PEG). The crystalline phase, microstructure, chemical composition, and morphology of the obtained samples were characterized by X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and transmission electron microscopy (TEM). The results show that spherical nano-HA with diameter of 30–50 nm can be synthesized in the presence of a certain concentration (2–6%) of PEG. The crystallinity of HA powder synthesized in the presence of PEG was higher than that synthesized in the absence of PEG, but the crystallinity of HA reduced with increasing the concentration of PEG. The electrical conductivity (EC) of the solution revealed that PEG reduced the transfer rate of Ca²⁺ in the process of HA crystallization, indicating the interaction between PEG and HA. The possible mechanism of formation spherical nano-HA was discussed.     

Characterization of microspherical semi-transparent solar cells and modules

Microspherical solar cells and modules have been fabricated. The spherical nature of these semi-transparent devices allows the microspherical cells to harvest both directly incident and diffuse components of sunlight thereby improving the solar energy conversion efficiency. Indoor and outdoor characterizations of these three dimensional semi-transparent cells and modules are carried out using a Lambertian reflector in order to assess the maximum efficiency of the devices. In the absence of the reflector the cell efficiency is 13.5% under standard illumination (100 mW cm⁻², A.M. 1.5, 25 °C). However, this is significantly enhanced in the presence of the reflector. Microspherical modules with the reflector are directly compared to similar semi-transparent modules comprised of traditional planar devices, in outdoor tests at low light intensity (2.5–25 mW cm⁻²) to further demonstrate the benefits of the design particularly at low angle of incident radiation.     

液化气球罐焊缝H2S应力腐蚀裂纹的返修补焊

对宁夏炼油厂一台200m3低合金钢球罐H2S应力腐蚀裂纹采用气刨打磨后补焊的返修方法表明，碳弧气刨时的骤热不会使裂纹向纵深扩展，只是必须在补焊前将返修部位焊缝两侧各100mm范围内打磨至完全露出金属光泽，以便彻底消除裂纹源，避免补焊时再产生新的微小裂纹。若返修深度不大于罐壁厚度的二分之一，则不必进行射线探伤检查，只须进行100％的超声波检查，在水压试验前后对返修部位进行100％磁粉探伤则是非常必要的。