Monomer casting nylon-6-b-polyether amine copolymers: Synthesis and properties

MC nylon-6-b-polyether amine copolymers were prepared with macro-initiator based on amino-terminated polyether amine functionalized with isocyanate via in-situ polymerization. It was found that the introduction of polyether amine delayed the polymerization process of caprolactam by increasing apparent activation energy and pre-exponential factor, resulting in the decrease of molecular weight of nylon-6. The motion of molecular chain of the copolymers was easy because of the decreased hydrogen bonds and weakened inter-molecular forces. The physical entanglement of molecular chains of the copolymers was significant and strong which increased the entanglement density. Only the nylon-6 phase crystallized in the copolymers and the crystal grain size, spherulite size and crystallinity of the copolymers decreased. A small amount of γ crystal formed at high polyether amine content. The copolymers presented obvious strain hardening behavior in stress-strain curves and the loss factor dramatically increased while the glass transition temperature and storage module decreased. The fracture surface of the copolymers became rough and presented hairy structure, indicating that the toughening mechanism of the copolymers corresponded to the multi-layer crack extension mechanism.     

A design of experiments investigation into dry separation using a Knelson Concentrator

Enhanced gravity, or centrifugal, separators have revolutionised gold processing over the past decades, significantly increasing the recovery of fine (−100 μm) free gold. One of the main drawbacks of centrifugal gravity concentrators is the large volume of water required (even if it is all recycled). With water becoming an ever increasingly important “commodity”, reducing this is of importance both from an environmental and a monetary point of view. This work investigated operating a laboratory scale Knelson Concentrator with a dry feed and using air as the fluidising medium. The feed used was a synthetic mixture of tungsten and quartz, used to mimic a gold ore. The response surface method and central composite design techniques were used to design the experiments and to model the results, with the experimental variables being the bowl speed (G-Level), air fluidising pressure and the feed rate. The models corresponded well to the experimental results, indicating that for this experimental setup, the optimal conditions were a bowl G-Level of 40 G, a feed rate of 220 g/min and an air fluidising pressure of 8 psi.     

Distributed learning consensus control based on neural networks for heterogeneous nonlinear multiagent systems

This paper considers a novel distributed iterative learning consensus control algorithm based on neural networks for the control of heterogeneous nonlinear multiagent systems. The system's unknown nonlinear function is approximated by suitable neural networks; the approximation error is countered by a robust term in the control. Two types of control algorithms, both of which utilize distributed learning laws, are provided to achieve consensus. In the provided control algorithms, the desired reference is considered to be an unknown factor and then estimated using the associated learning laws. The consensus convergence is proven by the composite energy function method. A numerical simulation is ultimately presented to demonstrate the efficacy of the proposed control schemes.     

垦71井区三维VSP资料波场分离方法应用研究

三维VSP资料是多偏移距VSP资料，资料中多种类型的波叠合在一起形成复杂波场。从复杂波场中分离出单一的保幅反射波波场是三维VSP波场分离的重要工作。常规二维VSP波场处理方法单一，难以适用于复杂的三维波场处理。针对三维VSP资料的波场特点，以分离上行反射P波为例，将单一波场分离方法加以适当组合，对垦71井区三维VSP实际资料进行了应用研究。结果表明，波场分离处理中叠加消去法和中值滤波相结合以及F—K滤波和中值滤波相结合的方法克服了单一方法的缺陷，波场处理后获得了波组特征明显、波场清晰单一的上行反射P波保幅波场，取得了较好的波场分离效果。     

Ni-Al2O3纳米复合电镀工艺的初步研究

初步研究了复合电镀各工艺条件：电流密度、镀液pH值和温度以及搅拌方式对Al2O3纳米微粒在镍基复合镀层中含量的影响。研究表明：电流密度增大不利于提高镀层中纳米微粒的含量；pH值增大也明显使复合量降低;镀液温度升高，镀层中微粒的复合量随之略有改变；电镀时，加强搅拌或适当改变搅拌方式，可以使复合镀居中的纳米微粒含量提高。还利用扫描电镜及能谱对Ni-Al2O3镀层表面进行了观察与分析。     

陶瓷及陶瓷基复合材料微缺陷的超声检测

为研究陶瓷及陶瓷基复合材料微缺陷的超声检测能力，针对一些人工缺陷试样进行了超声检测试验。试验主要采用了纵波垂直入射法和泄漏瑞利波法。通过试验结果，比较了两种方法的检测能力。     

Cu基络合物催化甲醇液相氧化羰化反应

针对甲醇液相氧化羰基化法合成碳酸二甲酯(DMC)工艺,开发了新型Cu基络合催化剂(CuB rnLm)。对CuB rnLm催化剂的活性及其稳定性进行了研究。实验结果表明,采用该催化剂,甲醇转化率和DMC选择性较高;元素价态和物质结构分析表明,CuB rnLm催化剂循环使用5次后仍保持较好的稳定性。采用正交设计和中心响应曲面法设计实验,并使用S tatistica软件进行统计分析,寻求出反应的主要影响因素,并得到优化的工艺条件:反应温度100~110℃、反应压力3.0~3.5M Pa、反应时间4~6h、CuB rnLm催化剂质量浓度(以甲醇的体积计)0.15~0.20g/mL。在此工艺条件下,甲醇转化率可达23%以上,DMC的选择性为96%~98%。     

WC/Cu复合材料制备及其高温性能

用机械合金化法结合冷变形，制备了WC／Cu复合材料，研究了冷变形后复合材料的组织特征和高温退火时韵性能变化。结果表明：烧结后的材料经冷变形，组织呈显著纤维状，WC颗粒弥散分布，密度明显提高，达到理论密度的99．2％；复合材料经600～900℃高温退火，强度和硬度略有下降，塑性则有大幅提高；900℃退火时未发生明显的再结晶，界面结合良好；所制备的WC／Cu复合材料有优良的综合性能。