全文获取类型
收费全文 | 1005篇 |
免费 | 12篇 |
国内免费 | 8篇 |
专业分类
电工技术 | 145篇 |
综合类 | 33篇 |
化学工业 | 76篇 |
金属工艺 | 62篇 |
机械仪表 | 232篇 |
建筑科学 | 8篇 |
矿业工程 | 4篇 |
能源动力 | 168篇 |
轻工业 | 5篇 |
水利工程 | 55篇 |
石油天然气 | 17篇 |
武器工业 | 10篇 |
无线电 | 7篇 |
一般工业技术 | 96篇 |
冶金工业 | 29篇 |
原子能技术 | 12篇 |
自动化技术 | 66篇 |
出版年
2024年 | 1篇 |
2023年 | 6篇 |
2022年 | 14篇 |
2021年 | 20篇 |
2020年 | 18篇 |
2019年 | 11篇 |
2018年 | 3篇 |
2017年 | 13篇 |
2016年 | 26篇 |
2015年 | 19篇 |
2014年 | 55篇 |
2013年 | 66篇 |
2012年 | 66篇 |
2011年 | 58篇 |
2010年 | 59篇 |
2009年 | 48篇 |
2008年 | 38篇 |
2007年 | 60篇 |
2006年 | 65篇 |
2005年 | 60篇 |
2004年 | 60篇 |
2003年 | 42篇 |
2002年 | 28篇 |
2001年 | 29篇 |
2000年 | 25篇 |
1999年 | 15篇 |
1998年 | 22篇 |
1997年 | 17篇 |
1996年 | 18篇 |
1995年 | 22篇 |
1994年 | 6篇 |
1993年 | 11篇 |
1992年 | 6篇 |
1991年 | 6篇 |
1990年 | 4篇 |
1989年 | 3篇 |
1988年 | 1篇 |
1987年 | 2篇 |
1986年 | 2篇 |
排序方式: 共有1025条查询结果,搜索用时 15 毫秒
1.
本文叙述了反应堆保护系统停棒与汽轮机降功率子系统的系统功能、保护参数和秦山核电站控制棒组插入监测器的设计与参数选择,确定了控制棒提升上极限值和在不同工况下棒插入低位、低-低位整定值,并在热态零功率条件下加以验证。试验证明参数选择是合理的,为功率运行阶段提供了数据。 相似文献
2.
YT-1000型油压自动调速器在运行中不能维持正常油压、在不增加任何设备的情况下,只改动二次接线的处理方法,就能消除隐患、解决问题。 相似文献
3.
简述轴承工作性质,巴氏合金应用与相组成的基本情况。论述汽轮机转子在两个电厂长期运行后,由于轴颈发生的不正常摩擦损伤,在大修改造中由无损检查、机械加工揭示出轴颈存在严重的渗巴氏合金现象,低熔点金属Sn、Sb与Cu向转子材料晶界的深层渗入最终导致了3根大型在投转子的严重开裂与报废。图11表2 相似文献
4.
5.
通过引进型国产300MW汽轮机在启动试运中出现的一次窜轴事故,根据计算机追忆打印的有关图表、数据分析了产生事故的原因,并提出了为防止类似事故重演应采取的措施和建议。经采取措施后该机组多次又在相同情况下启机,已安全运行。说明分析正确,措施得当,值得同类型机组借鉴。 相似文献
6.
7.
Experimental and computational analysis on guide vane losses of impulse turbine for wave energy conversion 总被引:1,自引:0,他引:1
This paper deals with the detailed flow analysis of impulse turbine with experimental and computed results for wave energy power conversion. Initially, several turbulence models have been used in two-dimensional (2-D) computational fluid dynamic (CFD) analysis to find a suitable model for this kind of slow speed unconventional turbine. Experiments have been conducted to validate the CFD results and also to analyze the aerodynamics at various stations of the turbine. The three-dimensional (3-D) CFD model with tip clearance has been generated to predict the internal flow and to understand the effect of tip clearance leakage flow on behavior of the turbine in design and off-design conditions. As a result, it is found from the 2-D results that the comparison between computed and experimental data is good, qualitatively and the turbulence model, standard k–ε can predict the experimental values reasonably well, especially the efficiency of the turbine. Experimental results reveal that the downstream guide vanes are more responsible for low efficiency of the turbine and it is measured that 21% average pressure is lost due to downstream guide vanes. It is proved from the 3-D CFD model with tip clearance that it can predict the experimental values quantitatively and qualitatively. Furthermore, it is estimated from the computed results that the efficiency of the turbine has been reduced about 4%, due to tip clearance leakage flow at higher flow coefficients. 相似文献
8.
Computational Fluid Dynamics (CFD) simulation is one of the important methods to study the performance and in-fluencing factors of turbine flow sensors. According to the working characteristics of the turbine flow sensor, the passive simulation method based on the six degrees of freedom (6-DOF) model and dynamic mesh is proposed in this paper. The reliability of the simulation method is verified by steady-state experiments and unsteady-state experiments. The results show that the trend of meter factor with flow rate acquired from the simulation is close to the experimental results, and the deviation between the simulation result and the experiment result is low with a maximum deviation of 2.88%. In the unsteady simulation study, the impeller speed changes with the inlet velocity of the turbine flow sensor, which has a good follow-up. The passive simulation method can be used to predict the dynamic performance of the turbine flow sensor. 相似文献
9.