Influences of chip serration on micro-topography of machined surface in high-speed cutting

Saw-tooth chip changes from macroscopically continuous ribbon to separated segments with the increase of cutting speed. The aim of this study is to find the correlations between chip morphology and machined surface micro-topography at different chip serration stages encountered in high speed cutting. High strength alloy steel AerMet100 was employed in orthogonal cutting experiments to obtain chips at different serration stages and corresponding machined surfaces. The chips and machined surfaces obtained were then examined with optical microscope (OM), scanning electron microscope (SEM), and white light interferometer (WLI). The result shows that chip serration causes micro-waves on machined surface, which increases machined surface roughness. However, wave amplitudes (surface roughness) at different serration stages are different. The principal factor influencing wave amplitude is the thickness of the sawed segment (tooth) of saw-tooth chip. With cutting parameters in this study, surface roughness contributed by chip serration ranges from 0.39 μm to 1.85 μm. This may bring on serious problems in the case of trying to replace grinding with high-speed cutting in rough machining. Some suggestions have been proposed to control the chip serration-caused surface roughness in high-speed cutting based on the results of the current study.     

一款紧凑增强型可变阻抗电磁带隙结构

基于传统AI-EBG结构,提出了一种小尺寸的增强型电磁带隙结构,实现了从0.5~9.4 GHz的宽频带-40 dB噪声抑制深度,且下截止频率减少到数百MHz,可有效抑制多层PCB板间地弹噪声。文中同时研究了EBG结构在高速电路应用时的信号完整性问题,使用差分信号方案可改善信号完整性。     

基于实际井眼轨迹的抽油杆柱API设计方法

目前的抽油杆柱设计方法大都基于设计井眼轨迹或经验公式，因此设计的抽油杆柱与井眼的匹配性并没有达到最优，结果可能影响了抽油杆柱的受力特性和寿命。概述了目前现有的抽油杆柱设计方法，提出了基于实际井眼轨迹的抽油杆柱API设计方法，即考虑到在三维空间中井下粘滞阻力及动载的影响，利用微单元分析方法计算出轴向载荷与轴向应力，然后在此基础上进行杆柱组合设计，并给出了设计流程。以江苏油田永21-3井为例，对几种设计方法的设计结果进行了对比分析，结果表明，江苏油田目前采用的抽油杆柱设计方法包含了人为经验因素，并不是最优的杆柱设计结果，有待进一步改进。     

基于水印的图像认证和完整性保护技术

数字水印技术的发展为解决图像认证和完整性保护问题提供了新的思路。对用于篡改检测和图像认证的水印技术做了综述。数字水印技术根据其识别差错的能力分为四种类型:易损水印、半易损水印、混合水印和自嵌入水印。最后还对水印认证技术的安全性问题进行了讨论。     

洼60-H26水平井套铣打捞技术

洼60-H26井是一口中曲率水平井,设计井深1 922 m,由于地面条件的限制,设计采用三维井眼轨道。该井水平段在钻至井深1 801 m时,发生卡钻事故。在卡钻事故处理过程中,采用测卡、爆炸松扣技术取出上部钻具后,应用了不同规格的套铣管对被卡钻具进行套铣,采用间歇式套铣方式实现了大斜度井段(45°-90°)的安全套铣,采用短套铣管完成了时水平井段内φ215．0 mm稳定器的套铣,采用φ228．6 mm套铣管成功套铣水平井段被卡LWD仪器,最后通过震击器震击成功解卡。详细介绍了洼60-H26水平井卡钻事故的处理过程,分析了在水平段处理卡钻事故的难点。该井处理卡钻事故的经验,对以后水平井施工中处理井下事故、打捞贵重仪器具有借鉴价值。     

Signal Integrity: Fault Modeling and Testing in High-Speed SoCs

As we approach 100 nm technology the interconnect issues are becoming one of the main concerns in the testing of gigahertz system-on-chips. Voltage distortion (noise) and delay violations (skew) contribute to the signal integrity loss and ultimately functional error, performance degradation and reliability problems. In this paper, we first define a model for integrity faults on the high-speed interconnects. Then, we present a BIST-based test methodology that includes two special cells to detect and measure noise and skew occurring on the interconnects of the gigahertz system-on-chips. Using an inexpensive test architecture the integrity information accumulated by these special cells can be scanned out for final test and reliability analysis.     

三种常用面积注水井网的比较与选择

本较系统地分析了三种常用面积井网系统的注水特点。指明了五点井网系统是面积井网中最强化的一种注水方式，适用于低渗透与特低渗透油藏的注水开发。     

涡轮钻具在高陡构造的应用及展望

介绍了涡轮钻具在秋参1井的应用情况,详细叙述了涡轮钻具在山前高陡构造快速钻进及防斜打直方面的优点,与常规钻井相比,机械钻速明显提高,钻井周期明显缩短,钻井成本明显下降,经济效益显著。     

��ԭ����φ118mm�����꾮�̾�����

作为一项钻井新技术，小眼井钻井可大幅度降低钻井成本,正愈来愈受到国内外各油气田的重视。小眼井钻井技术在中原油田主要用于φ139.7mm套管开窗侧钻井裸眼段的钻进，根据中原油田20余口φ139.7mm套管开窗侧钻井的钻井实践，探讨了中原油田φ118mm井眼钻 井的若干技术问题，其中包括钻头选择、钻井参数的优选、钻具组合和轨迹控制、固井技术及井下复杂情况和事故处理技术等。     

可循环泡沫钻井液在宝302井欠平衡井段的应用

介绍了可循环泡沫钻井液的配方，性能及在宝302井欠平衡井段中的应用情况，结果表明该体系悬浮和携岩能力强，抗高温，抗污染效果好，能够满足宝南区块深井欠平衡压力钻井的需要，且保护油气层效果好，同时，这也是国内首次将可循环泡沫钻井液成功应用于井泥岩及煤层井，拓宽了泡沫钻井液的应用范围。