Effects of genotype and treatment on the antioxidant activity of sweet potato in Taiwan

Six genotypes of sweet potato commercially available in Taiwan, including TNG57, TNG66, TNG68, TYY1, RP and WP, were used as samples in this study of the effects of steaming and kneading with pre-steaming treatments on the antioxidant components and antioxidant properties of methanolic extracts. Steam treatment increased the total phenols contents of all genotypes (2–13 times), flavonoids content of RP (1.3 times) and anthocyanins contents of RP and WP (5–6 times). Steam treatment also increased the reducing power and scavenging DPPH radical effect of sweet potato flours. For the methanolic extracts of steamed and kneaded flours, reducing powers were 0.02–1.70 at 5.0 mg ml⁻¹ and the scavenging effects on DPPH radicals were 19–92% at 2.5 mg ml⁻¹. Both showed the order of RP > WP > TYY1 and TNG66 > TNG57 and TNG68. However, the chelating effect of the six genotypes at 1.0 mg ml⁻¹ ranged from 50% to 73%. Contents of total phenols, flavonoids, and anthocyanins of sweet potato flours were significantly positively correlated with the reducing power and scavenging DPPH radical effects. After steaming and kneading treatments, RP showed the highest increase in the contents of total phenols, flavonoids and anthocyanins among the six genotypes studied.     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

Li2O在保护渣中的作用

采用在不同玻璃性的两种基渣中加入Ｌｉ２Ｏ为研究Ｌｉ２Ｏ对保护渣粘度，熔化温度及玻璃性能的影响，并对Ｌｉ２Ｏ改善保护渣玻璃性的机理进行了探讨，提出了寻找高速连铸保护渣中Ｌｉ２Ｏ的代用物的一种方法。     

Phenol novolac/poly(4- hydroxyphenylmaleimide) blend hardeners for DGEBA-type epoxy resin

Phenol novolac/poly (4-hydroxyphenylmaleimide) (PHPMI) blends were used as an epoxy resin hardener. The curing behavior of the above system and the thermal and mechanical properties of the cured epoxy resin were studied. It was not necessary to use a curing accelerator for this system, because PHPMI caused acceleration of the curing reaction. The curing mechanism of this system was investigated by using model compounds. Test pieces from the neat resins and the glass fiber reinforced resins were evaluated in terms of thermal and mechanical properties, respectively. It was found that heat resistance and mechanical properties were improved by increasing the amount of PHPMI in the hardener.     

地震复合波地质属性的研究方法

在地震资料解释中,地震复合波的地质属性问题一直没有得到很好地解决。本文针对松辽盆地砂泥岩薄互层的地质特点,提出了用波形合成追踪法研究地震复合波地质属性的方法。该方法在地震复合波正演合成过程中有五个可以识别的特征界面,其中 C 界面是地震复合波形成的主导界面;C 至 D 界面间的地层为形成地震复合波的主要地层。因此,找准 C 界面深度是建立地震复合波与钻孔地层间有机联系的关键,对地震地质层位准确标定和利用地震剖面复合波波形信息进行岩性预测极为重要。文中的应用实例表明,用该方法在松辽盆地较好地建立了地震信息与地质信息间的对应关系,解决了一些疑难地质问题,取得了较好的勘探效果。     

WTG420铁路罐车用钢的组织结构和力学性能分析

分析了ＷＴＧ４２０铁路罐车用钢的组织结构和力学性能。提出了冶炼与轧制的技术关键，其一，添加稀土元素改善钢中夹杂物；其二，采用控轧控冷使铁素体晶粒细化。     

析出物对IF钢性能的影响

一种阻性的晶闸管控制制动器被用于阻尼向串联补偿传输供电的热电发电机中的瞬态扭。重点放在开发适用的控制算，并通过多种不同的运行方式验证算法。作为一种制动器最优控制的可能方法，本文研究了离散等级一般化预先控制（ＧＰＣ），讨论了系统上ＧＰＣ执行过程中存在一些问题。用Ｐｒｏｎｇ分析来辩识系统传递函数，此传递函数与控制方案的考虑及强度特性有关。     

Effect of Stress State on Growth of Interfacial Intermetallic Compounds Between Sn-Ag-Cu Solder and Cu Substrates Coated with Electroless Ni Immersion Au

Excessive intermetallic compound (IMC) growth in solder joints will significantly decrease the reliability of the joints. IMC growth is known to be influenced by numerous factors during the component fabrication process and in service. It is reported that, other than temperature and holding time, stress can also influence the IMC growth behavior. However, no existing method can be used to study the effect of stress state on IMC growth in a controlled manner. This paper presents a novel method to study the effect of stress on interfacial IMC growth between Sn-Ag-Cu solder and a Cu substrate coated with electroless Ni immersion Au (ENIG). A C-ring was used and in-plane bending induced tensile and compressive stresses were applied by tightening the C-ring. Results revealed that in-plane compressive stress led to faster IMC growth as compared with in-plane tensile stress.     

Study on the long‐term thermal‐oxidative aging behavior of polyamide 6

The long‐term thermal‐oxidative aging behavior of polyamide 6 (PA6) was studied by comparison with the stabilized sample in this work. The variation of mechanical properties of the pure and the stabilized samples of PA6 with aging time at 110°C, 130°C, and 150°C were investigated, respectively. The aging mechanism of PA6 under heat and oxygen was studied in terms of the reduced viscosity, crystallization behavior, dynamic mechanical behavior, and chemical composition through the methods of polarized light microscopy (PLM), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), X‐ray photoelectron energy spectrum (XPS), and so on. The results indicated that at the initial stage of aging, the molecular crosslinking reaction of PA6 dominated resulting in the increase of the mechanical strength, reduced viscosity, and the glass transition temperature of the sample. And the molecular degradation dominated in the subsequent aging process resulting in the decrease of the melting temperature, the increase of the crystallinity, and the formation of the oxides and peroxides products. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal and mechanical properties of epoxy composites reinforced by a natural hydrophobic sand

If a low weight percentage of crude fine fillers can improve properties of polymer materials directly without complicated chemical treatment process involved, it will be significant for many industrial applications. Our previous study indicated that a kind of Cancun natural sand could be an effective filler material for polymer composites. In this current work, the epoxy composites reinforced by this kind of natural sand particles were prepared and thermal and mechanical properties of the composites containing up to 5 wt % of the sand particles were characterized. Results showed that the highest flexural strength appears in the epoxy composite containing 1 wt % sand particles. A damage model was used to interpret the flexural properties, which showed an acceptable agreement with the experimental results. The glass transition temperature, high temperature storage modulus, and dimensional stability of the sand/epoxy composites monotonically increased with the addition of the sand particles. The sand particle/epoxy composites also displayed a noticeable enhancement in thermal conductivity. Theoretical analysis showed that in addition to conduction, other heat transport mechanisms played roles in the improved heat transmission through the composites. As a natural porous micron-scale material, Cancun sand has the potential for applications in cost-effective composites with enhanced mechanical and thermal properties. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008