Plasma-assisted CO2 reforming of methane over Ni-based catalysts: Promoting role of Ag and Sn secondary metals

Carbon dioxide (CO₂) and methane (CH₄) are the primary greenhouse gases (GHGs) that drive global climate change. CO₂ reforming of CH₄ or dry reforming of CH₄ (DRM) is used for the simultaneous conversion of CO₂ and CH₄ into syngas and higher hydrocarbons. In this study, DRM was investigated using Ag–Ni/Al₂O₃ packing and Sn–Ni/Al₂O₃ packing in a parallel plate dielectric barrier discharge (DBD) reactor. The performance of the DBD reactor was significantly enhanced when applying Ag–Ni/Al₂O₃ and Sn–Ni/Al₂O₃ due to the relatively high electrical conductivity of Ag and Sn as well as their anti-coke performances. Using Ag–Ni/Al₂O₃ consisting of 1.5 wt% Ag and 5 wt% Ni/Al₂O₃ as the catalyst in the DBD reactor, 19% CH₄ conversion, 21% CO₂ conversion, 60% H₂ selectivity, 81% CO selectivity, energy efficiency of 7.9% and 0.74% (by mole) coke formation were achieved. In addition, using Sn–Ni/Al₂O₃, consisting of 0.5 wt% Sn and 5 wt% Ni/Al₂O₃, 15% CH₄ conversion, 19% CO₂ conversion, 64% H₂ selectivity, 70% CO selectivity, energy efficiency of 6.0%, and 2.1% (by mole) coke formation were achieved. Sn enhanced the reactant conversions and energy efficiency, and resulted in a reduction in coke formation; these results are comparable to that achieved when using the noble metal Ag. The decrease in the formation of coke could be correlated to the increase in the CO selectivity of the catalyst. Good dispersion of the secondary metals on Ni was found to be an important factor for the observed increases in the catalyst surface area and catalytic activities. Furthermore, the stability of the catalytic reactions was investigated for 1800 min over the 0.5 wt% Ag-5 wt% Ni/Al₂O₃ and 0.5 wt% Sn-5 wt% Ni/Al₂O₃ catalysts. The results showed an increase in the reactant conversions with an increase in the reaction time.     

Effect of heat treatment and zircon addition on the properties of low-cement castables based on recycled alumina grog

In this investigation, low-cement castables were prepared using 70% alumina grog aggregates obtained from crushed alumina brick waste. The aggregates were thermally treated at 1550 °C for 3 h. Four types of low-cement castables were prepared with various types of aggregates (alumina grog with or without thermal treatment) and fillers (with or without zircon addition), and they were evaluated in terms of their physical, thermal, and chemical properties. Microstructural analysis via scanning electron microscopy (SEM) was performed on the castables before and after slag attack. Compared to the other fabricated castables, the thermally treated alumina grog castables with zircon showed better physical properties, such as a higher bulk density, cold crushing strength, and modulus of rupture and a lower apparent porosity and water absorption. In addition, they had a higher positive linear thermal expansion, refractoriness under load, permanent linear change, and hot modulus of rupture. The results of the SEM with energy dispersive X-ray analysis of the prepared castables confirmed that the mullite and anorthite phases were predominant when zircon was not added and the zircon–mullite phase additionally appeared upon the incorporation of zircon. A quantitative elemental analysis via X-ray fluorescence spectroscopy was employed to determine the composition of the castables. X-ray diffraction analysis showed that the alumina grog castables had a high mullite and low anorthite content, and the thermally treated alumina grog had a high anorthite, low mullite, and high zircon content. The improvement in the mechanical and thermo-mechanical properties of the castables with thermally treated alumina grog and added zircon can be attributed to the formation of the zircon–mullite phase with a low mullite phase content.     

Chemically modified organic/inorganic nanoporous composite particles for the adsorption of reactive black 5 from aqueous solution

In the present work, we report a chemically modified polyacrylamide/silica nanoporous composite adsorbent for the removal of reactive black 5 (RB5) azo dye from aqueous solutions. The composite adsorbent was synthesized in a packed bed and modified by ethylenediamine (EDA). The adsorbent was characterized by Fourier transformation infrared (FT-IR), thermogravimetric analysis (TGA), thermoporometry, Brunauer, Emmett and Teller (BET) method and scanning electron microscopy (SEM). Mechanical stability of the adsorbent was examined in a packed bed by following the back-pressure of the column. Pore diameter of the composite adsorbent in dry and wet states was estimated to be about 18.71 nm and 12.61 nm, respectively. Adsorption experiments were performed in batch mode and effect of various operational parameters on the adsorption capability of the adsorbent was studied systematically. The maximum adsorption capacity of the modified composites was found to be 454.5 mg RB5/g of adsorbent. The equilibrium data were analyzed by Langmuir, Freundlich, Sips, BET and Redlich–Peterson isotherm models and found to fit well to the BET isotherm. The data kinetically followed the pseudo-second-order model. High adsorption capacity, fast removal mechanism, and good mechanical stability are three advantages of the presented composite for the removal of RB5.     

黑匣子高温测试仪的开发

采用物质的相变吸热原理，可以将高温环境传人保温箱的热量重新排回至高温环境，有效地提高了保温箱的抗高温能力，并对保温箱的隔热性能做了简单的理论推算和测温反向试验。温度测试仪选用超低功耗CPU，具有体积小、耗电少的优点，使黑匣子高温测试仪在运行过程中具有很好的安全可靠性。     

Cu-Mg/Al_2O_3催化乙醇和乙二胺合成N-乙基乙二胺

在固定床反应器内,乙醇和乙二胺经分子间催化胺化反应合成了N-乙基乙二胺(NEED),考察了一系列铜系催化剂的活性,并筛选出催化性能较好的Cu-Mg/A l2O3催化剂;通过X射线衍射和透射扫描电子显微镜方法表征了助剂Mg对Cu/A l2O3催化剂的改性作用;考察了助催化剂Mg含量、反应温度、反应压力、进料量和乙二胺含量等对Cu-Mg/A l2O3催化剂性能的影响。实验结果表明,Cu-Mg/A l2O3催化剂具有很好的活性和选择性;在200℃、3.0MPa、质量分数20%的乙二胺乙醇溶液、进料量1.0mL/m in的条件下,乙二胺的转化率为71.56%,产物NEED的选择性和收率分别为92.62%和69.86%;经过20 d的连续使用表明,Cu-Mg/A l2O3催化剂具有良好的稳定性。     

无钴黑色陶瓷颜料中铬含量测定的新方法

本文以盐酸羟胺作还原剂,研究了三价铬与二甲酚橙的显色反应,结果发现Cr3 在0～80滋g/50ml范围内,其吸光度与Cr3 含量成正比相关,用于无钴黑色陶瓷颜料中铬含量的测定,作出了回归方程,且进行了显著性检验,获得了理想的结果。     

镍层耐硝酸腐蚀性测试——一种简单的预先探测ENIG镍层“黑盘”现象的测试方法

随着更加精细的SMT、BGA等表面贴装技术的运用,化学沉镍金(ENIG)作为线路板最终表面处理得到了越来越广泛的应用,同时可怕的“黑盘”现象也随之更广泛地“流行”起来,直接导致贴装后元器件焊接点不规则接触不良。为了贯彻执行最好的流程控制和采取有效的预防措施,了解这种焊接失败的产生机理是非常重要的,及早的观测到可能发生“黑盘”现象的迹象变得同样关键。本文介绍了一种简单的预先探测ENIG镍层“黑盘”现象的测试方法-镍层耐硝酸腐蚀性测试,这种测试可以用于作为一种常规的测试方法监测一般化学沉镍溶液在有效使用寿命范围内新鲜沉积的镍层的质量。利用Weibull概率统计分析在不同的金属置换周期(MTO)下镍层的可靠性能表现。结合试验结果得出了一个镍层耐硝酸腐蚀性的判定标准。     

碳黑对苯乙烯自由基聚合反应影响的研究

研究了碳黑对苯乙烯单体聚合物反应的影响，结果表明，用过氧化苯甲酰作引发剂，普通碳黑子对苯乙烯的聚合有强烈的阻聚作用，而用偶氮二异丁腈引发聚合物时，普通碳黑的阻聚性很小，当时碳黑进行接枝处理后，接枝碳黑对苯乙烯自由基聚合的影响程度与接枝方法有关，其中过氧化苯甲酰 自由基枝枝碳黑的聚性变化较大。     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

NaY晶化母液制备硅铝胶的技术探讨

在导向剂法合成Y型分子筛的工艺下，晶化母液中SiO₂的含量为50～55g/l,Na₂O含量为20～25g/l，相当于模数为1.65～2.58的稀水玻璃，将晶化母液分离处理后，在晶化母液中加入一定量的硫酸铝溶液使硅沉淀,经过滤和水洗后即可制备出合格的硅铝胶，以便进行重新利用。