Fabrication of Cu/graphite film/Cu sandwich composites with ultrahigh thermal conductivity for thermal management applications

Effective thermal management of electronic integrated devices with high powder density has become a serious issue, which requires materials with high thermal conductivity (TC). In order to solve the problem of weak bonding between graphite and Cu, a novel Cu/graphite film/Cu sandwich composite (Cu/GF/Cu composite) with ultrahigh TC was fabricated by electro-deposition. The micro-riveting structure was introduced to enhance the bonding strength between graphite film and deposited Cu layers by preparing a rectangular array of micro-holes on the graphite film before electro-deposition. TC and mechanical properties of the composites with different graphite volume fractions and current densities were investigated. The results showed that the TC enhancement generated by the micro-riveting structure for Cu/GF/Cu composites at low graphite content was more effective than that at high graphite content, and the strong texture orientation of deposited Cu resulted in high TC. Under the optimizing preparing condition, the highest in-plane TC reached 824.3 W·m⁻¹·K⁻¹, while the ultimate tensile strength of this composite was about four times higher than that of the graphite film.     

Annealing temperature dependent structural and optical properties of electrodeposited CdSe thin films

Cadmium selenide films were synthesized using simple electrodeposition method on indium tin oxide coated glass substrates. The synthesized films were post annealed at 200 °C, 300 °C and 400 °C. X-ray diffraction of the films showed the hexagonal structure with crystallite size <3 nm for as deposited films and 3–25 nm for annealed films. The surface morphology of films using field emission scanning electron microscopy showed granular surface. The high resolution transmission electron microscopy of a crystallite of the film revealed lattice fringes which measured lattice spacing of 3.13 Å corresponding to (002) plane, indicating the lattice contraction effect, due to small size of CdSe nanocrystallite. The calculation of optical band gap using UV–visible absorption spectrum showed strong red-shift with increase in crystallite size, indicating to the charge confinement in CdSe nanocrystallite.     

Performance of surface ionic conduction single chamber fuel cell prepared by the sol gel method

The performance of surface ionic conduction single chamber fuel cell (SIC‐SCFC) prepared by the sol gel method was studied on electric characteristics due to the differences of the operating temperature and humidity, the electrode distance and electrolyte film depth, and multiple cells with the series and parallel connections. The SIC–SCFC was arranged the both anode of Pt and cathode of Au on the boehmite electrolyte. The open circuit voltage (OCV) of single cell achieved a maximum of 530mV in the dry gas mixtures of O₂/H₂=50% in room temperature operation, and but it became decrease as over 60%. The OCV was maintained the constant value between operating temperatures of 30°C to 80°C, and but it was decreased sharply at over 90°C because a humidity on the cell became lower as increasing operating temperature. Then, the cell property was improved to 120°C by adding to the humidity of 70% using a humidifier. The electrode distance and the electrolyte film depth of SIC‐SCFC found to be contributed to the reductions of the cell resistance and the surface roughness on the electrode, respectively. Moreover, the power property of SIC‐SCFC was significantly improved by cell stacks comprised of the series or parallel connection of a cell.     

Formation of ST12 phase Ge nanoparticles in ZnO thin films

In this work, we focus on the Ge nanoparticles (Ge-np) embedded ZnO multilayered thin films. Effects of reactive and nonreactive growth of ZnO layers on the rapid thermal annealing (RTA) induced formation of Ge-np have been specifically investigated. The samples were deposited by sequential r.f. and d.c. sputtering of ZnO and Ge thin film layers, respectively on Si substrates. As-prepared thin film samples have been exposed to an ex-situ RTA at 600 °C for 60 s under forming gas atmosphere. Structural characterizations have been performed by X-ray Diffraction (XRD), Raman scattering, Secondary Ion Mass Spectroscopy (SIMS), and Scanning Electron Microscopy (SEM) techniques. It has been realized that reactive or nonreactive growth of ZnO layers significantly influences the morphology of the ZnO: Ge samples, most prominently the crystal structure of Ge-np. XRD and Raman analysis have revealed that while reactive growth results in a mixture of diamond cubic (DC) and simple tetragonal (ST12) Ge-np, nonreactive growth leads to the formation of only DC Ge-np upon RTA process. Formation of ST12 Ge-np has been discussed based on structural differences due to reactive and nonreactive growth of ZnO embedding layer.     

一种新型注入剖面组合测井仪及其应用

为了提高注入剖面测井的准确性，研制了一种新型注入剖面组合测井仪。该仪器由流量处理单元、伽马处理单元、井温处理单元、磁性定位处理单元、调制式传输、电源电路六部分组成。一次下井可同时测取流量、伽马、井温、磁性定位四组参数。具有测取资料精度高、单芯电缆传输、流量可单点测量也可连续测量以厦现场监测和维修方便等特点。     

含硫化氢气井钻井过程中的腐蚀因素与防护研究

在含硫气井的钻井过程中对于HRC大于22的钻具钢材除了腐蚀疲劳之外，在pH值小于9的环境中会发生硫化物应力腐蚀破裂，这种破坏比腐蚀疲劳更突然、更快，使钻杆大量损坏。含硫气井在钻井过程中，由于湿硫化氢的出现，常常会出现油管、套管、钻井设备、钻井仪器以及对支持保护管柱的水泥环柱等腐蚀和损坏问题，为此，阐述了湿硫化氢的腐蚀特点、机理，归纳总结了影响腐蚀的因素，综述了如何在这些方面防止其腐蚀，使损失减小，为指导油管、套管防腐工程实践提供了依据。建议在钻井过程中采用碱性钻井液，其pH值可到9或更高(至pH值12)，以减缓或防止钻井过程中电化学从硫化物应力腐蚀破裂；含硫气井用的钻杆应该间歇使用。钻杆停用堆置时间可使其放氢，使钻杆恢复韧性，防止硫化物应力腐蚀断裂。     

Effect of select parameters on the properties of edible film from water-soluble fish proteins in surimi wash-water

Edible film from water-soluble fish proteins were developed by casting film solution on leveled trays and effects of pH (9.5, 10.0 and 10.5), heating temperature (60, 70 and 80 °C), and heating time (10, 20 and 30 min) of the film solution on various film properties were determined using Response Surface Methodology (RSM). The impact of pH and heating temperature of film solution was more significant, overall, on the film's properties than heating time. Contour plots of tensile strength and elongation at break was highest at pH of 10.0 at 70 °C (2.75-3.02 MPa) but low in elongation at break (6.35-9.16%), while water vapor permeability and oxygen permeability were at their lowest (58.55-65.96 g mm/m² d kPa and 351.33-624.18 cm³ μm/m² d kPa). There was a direct correlation between the films’ and proteins’ solubility on one hand, and heating temperature of film solution on the other, which reversed with change in pH of film solution. Film color was darker and more yellowish with increase in the pH of film solution.     

膨胀套管的弹塑性理论分析

分析认为，膨胀套管在膨胀过程中先进入弹性阶段，然后进入弹塑性阶段，最后进入塑性流动阶段。采用弹塑性分析方法，对膨胀套管膨胀过程中套管内壁的受力与变形进行了研究，模拟了其成形的过程，并建立了解析解，为膨胀套管膨胀操作过程中确定关键操作参数提供了理论支持。根据推导出的力学模型，计算出了外径107．9mm、钢级为J55的膨胀套管膨胀到直径139．7mm时膨胀芯头拉头处的轴向力为195．94kN。     

Influence of Polyalkylmethacrylate VII on Boundary Film Formation,Friction,Wear and Efficiency of Lubricants

1 Influence of PAMAon Boundary Fil mFormation and Friction1.1 Experi mental methodsUltra-thin optical interferometry has been used tostudy thinlubricating fil ms for more than a decade and theexperi mental details of this technique have been reportedpreviously[1].The principle of the test setup is shown inFigure1.A polished steel ball is loaded and rolled againstthe flat surface of a glass disc that is coated with a thinsemi-reflecting chromiumlayer and a silica spacer of about500nmthickne…     

Nonstationary Simulation Model of Absorber with Falling Film of Suspension

A nonstationary model of SO₂ absorption from a gas phase to a countercurrent falling film of absorbing slurry was developed. Laminar, wavy and turbulent film structures were considered based on published information. Resistances to the mass transfer on the gas and the liquid sides of the interphase were considered, together with chemical reactions in the liquid phase. Relevant chemical equilibria in the liquid phase were modeled. Original experimental data on the neutralization reagent dissolution rate presented as a polydispersed two‐phase system of solids and on the rate of dissolved sulfite oxidation were used. The model was verified with experimental data from a laboratory‐scale falling‐film absorber using a single vertical tube under various geometrical and operating conditions, and a very good agreement was found with the experiment. Parametric sensitivity analysis showed the critical parts of the model.