Calcium deficient hydroxyapatite by precipitation: Continuous process by vortex reactor and semi-batch synthesis

Precipitation of calcium deficient hydroxyapatite nanoparticles in an environmentally benign manner by using only dilute solutions of calcium hydroxide and phosphoric acid without pH adjustment and addition of other chemicals, and water, being the only by-product was investigated by using continuous flow Vortex Reactor (VR) and Semi-Batch Reactor (SBR). The effect of hydrodynamics by changing the Reynolds number of the jets providing residence times of 8.4 ms to 4.37 s for VR, and by changing the stirrer speed between 100 rpm (Re = 2656) and 1000 rpm (Re = 26560) for SBR, on the particle size, particle size distribution, and morphology of the particles was investigated for both systems. It has been shown that it is possible to produce pure phase hydroxyapatite nanoparticles in the desired morphology by changing production system, without resorting to additives. While VR produced rod-like particles with the crystallite size around 4 nm, SBR produced spherical particles with the crystallite size of around 5 nm.     

A facile co-solvent strategy for preparation of graphene nanoplatelet powder: An industrially viable innovative approach

We report an industrially viable promising approach to produce micrometer-sized multilayer graphene nanoplatelet powder (MGNP) in a scalable quantity via microwave-assisted exfoliation of graphite (MEG) and fragmented into MGNP through liquid-phase exfoliation in the co-solvent mixture by kitchen mixer (KM). KM allows rapid delaminating MEG into MGNP by shear force dominated exfoliation. Majority of MGNPs are with a diameter of few micrometers and thickness is in nanometers. MGNP are crystalline with very limited defects was confirmed by Raman measurements and transmission electron microscopy. This process transforms, more than 86% of graphite flakes into MGNP. This advanced approach opens a new pathway to produce MGNP in bulk quantity as it is feasible, rapid, and cost-effective.     

柔性联轴节在减小转子系统扭转冲击运动中的作用

通过对大型振动磨机运动特性的研究分析,把其旋转系统简化为由两个柔性联轴节连接的三转子系统。建立了柔性连接的三转子系统在冲击转矩作用下的运动方程,对方程求解得到了柔性连接转子系统的扭转冲击响应。通过对冲击响应随柔性联轴节扭转刚度和阻尼变化规律的讨论分析,发现减小柔性联轴节的扭转刚度和增大柔性联轴节的阻尼,可以减小转子系统的扭转冲击响应。     

Non-equilibrium particle motion in the vicinity of a single blade

The motion of sand particles close to a single moving blade was investigated using Positron Emission Particle Tracking (PEPT) during the period in which the free bed surface profile was evolving to an equilibrium shape. The area affected by the blade was divided into active and inactive regions and these were analysed separately. The characteristic heart-shape of the active region in the plan view was determined. An approximately 10-particle-diameter wide velocity transition zone is found between the two regions. While the tracer particle is in the inactive region moving away from the blade, the time dependence of the axial displacement is well described by a logarithmic relationship. The probability of particle movement towards the centre of the blade was quantified using a “central tendency” index. The calculated central tendency shows maxima at each side of the blade. The separation of the two maxima, which indicates the width of the active region, increases with fill level but is independent of rotational speed.     

具有初始弯曲转子振动峰值的控制方法

本文从理论上研究了控制初始弯曲引起的转子振动幅值的一种新方法。通过在与转轴初始弯曲方向成较大夹角的方向添加不平衡质量的方法 ,使转子新的不平衡方向与初始弯曲方向夹角接近 180° ,则可以减小转子在临界转速附近的振幅。无论新的不平衡参数大于或小于初始弯曲参数 ,只要新的不平衡参数不至于太大 ,则临界转速附近的振幅响应肯定会得到改善。特别是当新的不平衡参数近似等于初始弯曲参数时 ,无论转速高低 ,振幅都会大幅下降。当重力参数、外阻尼系数和内阻尼系数改变后仍有同样结论。本文援引文献 [2 ]中的实例对这种方法进行了验证 ,并给出了解决类似故障的步骤。本文的方法可用于处理生产实际中转轴初弯引起的振动问题     

PTA压力离心机转子的改造

介绍了PTA压力离心机的主要性能参数、工作原理、分离效果的影响因素。为了增大沉渣在过渡区及脱水区滞留的时问，同时为达到在过渡区及脱水区对沉渣加入纯净水进行再冲洗的目的，对螺旋送料转子、挡液环、进料管进行了改造。改造后，沉渣在脱水区的停留时间由0．44a增至0．72s，2．5～3t／h的冲洗水对脱水区的沉渣进行冲洗效果较好。产品中的杂质质量分数较改造前减少15％，产品优等品率提高到99％。     

油气润滑系统在四切分轧制技术上的应用

本文介绍了油气润滑技术的工作原理及特点，阐述了该系统在四切分轧制技术上的应用与延伸。     

端电压比较法直接寻找无刷直流电动机换相点及其斩波调速

提供了一种利用端电压比较结合软件算法直接寻找直流无刷无位置传感器电动机换相点的方案，解决了直流无刷无位置传感器电动机控制的关键问题－转子位置检测，并以单片机PIC16C72为核心构成先进的数字控制系统，实现了软件斩波调速。     

利用钨极氩弧焊技术修复1#汽轮机转子的实践

本文主要介绍了我厂利用钨极氩弧焊将1#发电机组汽轮机转子修复的工艺过程.     

起重机吊钩拖动绕线电动机他励双高调速系统

本文提出励磁电流可自动控制的他励式双高调速系统设计方案。系统在提升特别是在下放重物时，具有较硬的机械性；在负载１０－１００％的变化范围内，可实现最大偏差Δｎｍａｘ／ｎｍｉｎ１００％≤１０％，调速范围Ｄ≥１０；在满载运行条件下，可节约电能８０％以上。