An investigation into the effect of various chemical and physical treatments of a South African phosphogypsum to render it suitable as a set retarder for cement

The work describes various physical and chemical treatments to eliminate the deleterious effects of impurities in phosphogypsum on the delayed setting time and impaired strength development behaviour of cement to which it was added as a set regulator. The physical treatments included washing, milling, and ultrasonic treatment of the material, while the chemical treatments dealt with acidic and basic additions to the phosphogypsum during the washing stage. It was found that chemical treatment with a milk of lime solution, which is often recommended in literature, was ineffective in reducing set retardation. Treatment with ammonium hydroxide or sulphuric acid was more effective in this regard. Intergrinding phosphogypsum with slaked lime improved its effectiveness in reducing set retardation, but the use of unslaked lime was less effective and also resulted in marked reductions in compressive strengths. A combined treatment of wet milling phosphogypsum with a lime slurry in a ball mall was derived from these experiments and is recommended for full-scale plant applications.     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

NaY晶化母液制备硅铝胶的技术探讨

在导向剂法合成Y型分子筛的工艺下，晶化母液中SiO₂的含量为50～55g/l,Na₂O含量为20～25g/l，相当于模数为1.65～2.58的稀水玻璃，将晶化母液分离处理后，在晶化母液中加入一定量的硫酸铝溶液使硅沉淀,经过滤和水洗后即可制备出合格的硅铝胶，以便进行重新利用。     

新世纪我国压铸业与国际接轨的思考

针对中国压铸行业的现状和存在的问题 ,以及当前的机遇和面临的挑战 ,论述了中国压铸工业进入 2 1世纪所面临的新形势及应采取的对策     

浅谈冲压模具的维修要领及常见故障的排除

介绍冲压模具修理和检查各环节的主要工作内容及维修要领 ,列举了常见故障的排除方法 ,通过总结实际生产中的修模经验 ,对缩短修模周期 ,降低成本 ,延长模具寿命有一定的参考价值。。     

PTC热敏电阻的现状与发展趋势(续一)

基于对1995年以来,国内外PTC热敏电阻的研究,介绍了PTC热敏电阻用原料(BaCO3、TiO2、BaTiO3、SrCO3、PbO、Pb3O4、SrTiO3、PbTiO3、Y2O3、Nb2O5、CaCO3、SiO2等);材料(BaTiO3系、V2O3系及高分子);生产技术(瓷粉制造、烧成、芯片制造、质量评定、理化分析、片式PTC生产);重点产品(消磁、马达启动、限流及加热等用)以及基础研究(相变应力模型、表面势垒模型)等方面的现状及今后的发展趋势。     

超大型材生产经验

对几种超大型材挤压生产的工艺技术、工模具设计、挤压参数控制等过程进行了分析，通过例子总结了挤压生产超大型材的经验及关键技术。     

邻苯二甲酸酯鼓泡生物降解

该课题测试了邻苯二甲酸酯类化合物的鼓泡生物降解行为。结果表明，邻苯二甲酸酯的降解速率常数（kb)与其烷基链长度之间存在良好的相关性，kb=0.0009x^2-0.019x 0.1123，相关系数r=0.9906；浓度超过500mg/L时，邻苯二甲酸二乙酯可抑制自身的生物降解；中间产物邻苯二甲酸浓度超过50mg/L时，也对邻苯二甲酸二乙酯的生物降解有明显的抑制作用。     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.