Structural modifications and fibre processing of hydroxy-functionalised mesogenic polyazomethines

A number of semiflexible homopolyazomethines and copolyazomethines based on hydroxy-functionalised mesogenic cores have been synthesised and characterised. The reported polymers include structural modifications such as an alteration of the coaxiality, shortening of the flexible spacers or copolymerisation to attain materials with reduced melting temperatures and suitable processability. These structural alterations have been introduced by condensing different ,ω-bis-[(4-formyl-3-hydroxyphenyl)oxy]alkanes with 2-methyl-1,4-phenylenediamine and/or 4-methyl-1,3-phenylenediamine. Fibres have been melt extruded from those nematic polyazomethines with the most favourable thermal properties. As-spun and tension-annealed fibres have been investigated by thermal analysis (TGA and DSC), X-ray diffraction and SEM microscopy in an attempt to infer a relationship between microstructure and tensile properties. From the results presented here, copolymerisation incorporating flexible spacers of different lengths seems to be the best strategy to balance ease of processing and tensile properties. Some of the fibres have improved mechanical properties compared with those previously reported for this class of semiflexible polyazomethine. A nematic polyazomethine with a decamethylenic spacer has also been modified with low percentages of several metal ions [Fe(III), Zn(II), V(IV) and Ni(II)] in order to establish a comparison with previously reported Cu(II)-modified fibres.     

Effects of solvent and temperature on the coupling agent/epoxy resin interface

Increased wetting of the coupling agent/epoxy resin interface was observed when γ-glycidoxypropyltrimethoxysilane, polyfunctional aminosilane and γ-aminopropyltriethoxysilane were applied respectively from methyllethylketone, dimethylformamide and water on woven glass cloths which had been cleaned at 300°C. However, when factory-applied coupling agents were burnt off the woven cloths and fresh coupling agents re-applied, it was found that the nature of the factory-applied coupling agent influenced subsequent wetting. Thinner glass fibres showed a greater improvement in wetting rate than thicker fibres in those solvents identified to be good for improved wettability, irrespective of the heat-cleaning temperature.     

Biodegradable hollow microfibres to produce bioactive scaffolds

Biodegradable hollow microfibres containing particles loaded with specific active agents can be potentially employed to produce a special kind of substrate for tissue engineering, able to function as a scaffold and at the same time to act as a drug‐releasing system. Biodegradable hollow microfibres based on poly(lactic acid) were produced by a dry–wet spinning procedure. Drug‐loaded microparticles were prepared by a simple oil‐in‐water emulsion and entrapped inside the fibres. The morphology of both fibres and particles was investigated by scanning electron microscopy. The mechanical and thermal properties of the fibres were investigated by tensile tests and differential scanning calorimetry. In vitro tests were performed to evaluate the release of the drug from the fibres loaded with the particles Copyright © 2004 Society of Chemical Industry     

Effect of Bonder at Skin/Core Interface on the Mechanical Performances of Sandwich Structures Used in Marine Industry

The present work is aimed to extend the knowledge of mechanical properties of sandwich structures used for marine applications focusing on the possibility to increase the performances of such structures by adding a bonder at the skin/core interface. Therefore, three sandwich structures that are utilised in different structural components of a yacht were realised by manual lay-up. The mechanical characterisation was performed by flatwise compressive, edgewise compressive and three point flexural tests. The tests execution has allowed both to determine the mechanical performances and to understand the fracture mechanisms that take place when the bonder is added in the stacking sequence of the samples.     

Behaviour of ±45° glass/epoxy filament wound composite tubes under quasi-static equal biaxial tension–compression loading: experimental results

The primary aim of this paper is to present results describing in detail the behaviour of ±45° E-glass/MY750 (GRP) tubes, of various wall thicknesses, subjected to equal biaxial tension–compression loading, generated under combined internal pressure and axial compression. The role played by the non-linear lamina shear has also been assessed by comparing various shear stress–strain curves for embedded laminae (extracted from tests on ±45° tubes subjected to circumferential: axial stress ratios SR=1:0, 1:−1 and 2.3:−1) with that of an ‘isolated’ lamina (measured from torsion of 90° tubes). Extracted shear failure strains, for embedded laminae, were more than four fold larger than those measured at ultimate failure for an ‘isolated’ lamina. Soft characteristics were observed in the embedded lamina and these were believed to be due to interaction between early matrix damage initiation (and propagation) and shear. Factors affecting the behaviour of the tubes, such as bulging, scissoring, thermal stresses and stress variation through the thickness are discussed.     

Creep of aromatic polyamide fibres

Creep of Kevlar 29, Kevlar 49 and PRD 49-III fibres was investigated. The fibres exhibited transient creep and the strain-time relationship was represented by a logarithmic time law. The creep strain recovered with time when the load was removed. Upon reloading to the same creep stress the strain-time relationship was again logarithmic but the creep rate was reduced. Modulus measurements were made during the creep test and these showed that the modulus increased with time. This result indicated a crystallite rotation mechanism which could account for the experimentally observed creep strain. Creep in PRD 49-III fibres exhibited a small temperature dependence over the temperature range 20°C to 150°C. The apparent creep activation energy was consistent with the range of values reported for hydrogen bonding. This suggests one possible creep mechanism in which the combined action of stress and thermal activation causes rearrangement of intercrystalline bonds in the crystallite boundaries resulting in boundary creep. Boundary creep allows crystallite rotation which produces the macroscopic creep strain. Boundary creep is discussed in terms of the fibre morphology and a model of delayed elasticity.     

Sol-gel processing: A versatile concept for special glasses and ceramics

The various parameters related to sol-gel processing are discussed with special reference to those which usually attract less attention but depending on the final product in mind, can play important roles. The versatility of the sol-gel technique in materials preparation is demonstrated by discussing the various products developed at the author’s laboratory by using this processing method.     

Biosorption of Phenol onto Posidonia oceanica (L.) Seagrass in Batch System: Equilibrium and Kinetic Modelling

In this research, the biosorption of phenol using the fibres of a Mediterranean seagrass Posidonia oceanica (L.) was studied. Batch experimental procedures were made to investigate the ability of this novel marine biomass to remove phenol from aqueous phase. The influences of pH and contact time at different initial concentrations were evaluated. The results showed that biosorption capacity was enhanced using solution pH equal to 5.2. The modelling results showed that pseudo‐second‐order and Redlich‐Peterson models were found to be the most suitable to satisfactory describe the kinetic and equilibrium adsorption data, respectively.     

Asbestos replacement aspects: Modification of the fibre-matrix interphase in lonomer based composites

Asbestos fibres, of the chrysotile variety, and chopped carbon fibres were pretreated by an in-situ polycondensation technique eventually resulting in a polyamide coating on the fibre surface. Ionomer based composites containing either carbon or asbestos fibres in random in plane fibre orientation were prepared, and the influence of this coating process on the tensile properties was investigated. It was found that for the asbestos-filled composites the presence of the nylon 6,6 interlayer improves the tensile performance, especially at moderate polyamide depositions. This is not the case with the pretreated carbon-filled composites for which carbon fibres with higher polyamide contents are preferred. Combinations of the treated asbestos fibres with carbon and/or aramid fibres may be used to reduce the asbestos content in asbestos-only based engineering plastics.     

复合材料压缩破坏模式的缺陷敏感性

本文基于弹塑性分叉理论研究单向纤维增强复合材料的压缩破坏模式和压缩强度对缺陷的敏感性问题。对于常见复合材料,所得结论是:无缺陷或者小缺陷情况的破坏模式为倾斜破坏带;大缺陷情况的破坏模式为水平破坏带;形成水平破坏带的压力值小于形成倾斜破坏带的压力。