磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

沉管隧道水下最终接头施工技术初探

简述了沉管隧道水下最终接头施工技术的应用现状，结合具体隧道工程实例，从外模工程、混凝土结构两方面介绍了最终接头施工技术，表明了该技术具有运用价值。     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

A goal-striving life event and the onset of hypomanic and depressive episodes and symptoms: Perspective from the Behavioral Approach System (BAS) dysregulation theory.

On the basis of the behavioral approach system (BAS) dysregulation theory of bipolar disorder, this study examined the relation between occurrence of a BAS activation-relevant life event--goal striving--and onset of hypomanic and depressive episodes and symptoms. In particular, the authors examined the relation between preparing for and completing final exams (a goal-striving event) and onset of bipolar spectrum episodes and symptoms in college students with bipolar II disorder or cyclothymia (i.e., "soft" bipolar spectrum conditions). One hundred fifty-nine individuals with either a bipolar spectrum disorder (n=68) or no major affective psychopathology (controls; n=91) were further classified on the basis of whether they were college students (i.e., completed final exams). Consistent with the BAS dysregulation theory, preparing for and completing final exams was associated with an increase in hypomanic but not depressive episodes and symptoms in individuals with a soft bipolar spectrum diagnosis. Furthermore, self-reported BAS sensitivity moderated the presence of certain hypomanic symptoms during final exams. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

成形磨削中砂轮修整精度的研究

成形磨削一般采用金刚石笔来修整所需要的砂轮形状，金刚石笔在安装中的位置误差将影响被加工工件的精度，本文对此误差的大小进行了分析。     

实行工程预决算审计 严格控制投资成本

针对目前企业固定资产投资中存在的投资超概算问题 ,论述了实行工程预决算审计的必要性 ,结合江西铜业股份有限公司的实践阐明了如何实行工程预决算审计 ,以达到提高投资效益的目的。     

在线磨辊辊面粗糙度的实验研究

影响轧辊表面粗糙度的因素很多，为此对影响辊面粗糙度的因素进行了系统分析和实验研究，得出了轧辊和砂轮的速度、砂轮粒度、砂轮直径及磨削液等主要因素对轧辊表面粗糙度影响的一般规律。利用回归分析的方法建立了轧辊表面粗糙度的数学模型，并将计算值与实测值进行了比较，发现两者基本一致。此项研究为适时控制冷轧带钢在线磨辊辊面粗糙度提供了计算模型。     

1 000 t/d湿磨干烧生产线工艺特点和调试

湿法生产线的技术更新改造有异地新建新型干法生产线和原地改成湿磨干法生产线二种。浙江虎山集团(?)3.0 m×88.68 m湿法线的改造,经方案比较和生产原料的状况,采用了湿磨干烧方案。其中,料浆脱水采用了真空吸滤法,浇成系统采用了南京院专有技术。改造投产后,获得了优质、高产、低耗和安全生产的技改效果。     

钢管打捆包装机的设计

为了提高包装质量，取代原人工打捆，设计开发了钢管打捆包装机，该包装机采用碾拉工艺，通过综合分析拉紧与绞纽组合动作的传动，实现了钢管的打捆包装机械化，使钢管包装质量达到了ISO9000标准要求，同时降低了劳动强度。