Time reversibility of the discrete element method

An algorithm is presented for discrete element method simulations of energy-conserving systems of frictionless, spherical particles in a reversed-time frame. This algorithm is verified, within the limits of round-off error, through implementation in the LAMMPS code. Mechanisms for energy dissipation such as interparticle friction, damping, rotational resistance, particle crushing, or bond breakage cannot be incorporated into this algorithm without causing time irreversibility. This theoretical development is applied to critical-state soil mechanics as an exemplar. It is shown that the convergence of soil samples, which differ only in terms of their initial void ratio, to the same critical state requires the presence of shear forces and frictional dissipation within the soil system.     

尿素装置液位仪表失真分析及处理

介绍了尿素装置中3起液位仪表失真案例,分析了故障现象和设备工况,确定失真原因,采取了相应的处理措施,解决了仪表故障。     

A miniature triaxial apparatus for investigating the micromechanics of granular soils with in situ X-ray micro-tomography scanning

The development of a miniature triaxial apparatus is presented. In conjunction with an X-ray micro-tomography (termed as X-ray μCT hereafter) facility and advanced image processing techniques, this apparatus can be used for in situ investigation of the micro-scale mechanical behavior of granular soils under shear. The apparatus allows for triaxial testing of a miniature dry sample with a size of \mathrm{8}\hspace{0.17em}\mathrm{mm}\times \mathrm{16}\hspace{0.17em}\mathrm{mm} (diameter \times height). In situ triaxial testing of a 0.4–0.8 mm Leighton Buzzard sand (LBS) under a constant confining pressure of 500 kPa is presented. The evolutions of local porosities (i.e., the porosities of regions associated with individual particles), particle kinematics (i.e., particle translation and particle rotation) of the sample during the shear are quantitatively studied using image processing and analysis techniques. Meanwhile, a novel method is presented to quantify the volumetric strain distribution of the sample based on the results of local porosities and particle tracking. It is found that the sample, with nearly homogenous initial local porosities, starts to exhibit obvious inhomogeneity of local porosities and localization of particle kinematics and volumetric strain around the peak of deviatoric stress. In the post-peak shear stage, large local porosities and volumetric dilation mainly occur in a localized band. The developed triaxial apparatus, in its combined use of X-ray μCT imaging techniques, is a powerful tool to investigate the micro-scale mechanical behavior of granular soils.     

24万t/a尿素装置技术改造总结

针对新化化肥有限公司尿素装置存在的问题进行了技术改造,从尿素合成塔、中压分解吸收、低压分解吸收、闪蒸等方面分析了产生问题的原因,提出了改进措施和实施方案。对改造前后工艺指标、产品质量和经济效益进行了对比和分析。改造结果表明.生产能力提高25％,5个月可收回全部投资。     

无机阻燃剂高聚合度聚磷酸铵的研制

以五氧化二磷、磷酸铵盐、尿素为原料、氨气为保护气,制备了高聚合度聚磷酸铵无机阻燃剂。考察了五氧化二磷、磷酸铵盐、尿素的用量和反应温度对聚磷酸铵平均聚合度的影响。采用端基滴定法测定了聚磷酸铵的聚合度,并用X射线衍射(XRD)法表征了聚磷酸铵的晶体结构,同时测定了聚磷酸铵的粒度和溶解度。实验结果表明,制备聚磷酸铵的最佳反应条件为:n(磷酸氢二铵)∶n(五氧化二磷)∶n(尿素)=1∶1∶0.3,反应温度280~300℃,反应时间40m in,热处理温度250~280℃,热处理时间110m in。在此条件下制备的聚磷酸铵的平均聚合度大于600,平均粒径直径小于50μm,在水中的溶解度小于0.4g;XRD表征结果表明,所合成的物质为Ⅱ型聚磷酸铵。     

水溶液全循环法尿素装置中压分解"三种工艺"的比较

以生产数据结合理论计算的方法系统地比较、分析了水溶液全循环法尿素装置中中压分解“三种工艺”的热能利用、甲铵分解率、总氨蒸出率、水平衡量、一分加热器生产能力等方面的情况，提出应用和配置预分离-预蒸馏工艺的方法，评论该工艺在水溶液全循环法中的地位和作用。     

大颗粒尿素造粒工艺简介

介绍了大颗粒尿素造粒工艺，着重介绍了荷兰NSM公司的流化床造粒技术和法国K－T公司的流化床转鼓造粒（FDG）技术。     

尿素醇解合成碳酸酯类化合物技术进展

综述了用尿素醇解合成碳酸酯类化合物的技术进展 ,重点介绍尿素醇解合成碳酸二甲酯研究现状以及与其它工艺路线的比较 ,另外也介绍了尿素醇解合成长碳链脂肪族和芳香族类碳酸酯的研究进展。     

Granular gases in mechanical engineering: on the origin of heterogeneous ultrasonic shot peening

The behavior of an ultrasonic shot peening process is observed and analyzed by using a model of inelastic hard spheres in a gravitational field that are fluidized by a vibrating bottom wall (sonotrode) in a cylindrical chamber. A marked heterogeneous distribution of impacts appears when the collision between the shot and the side wall becomes inelastic with constant dissipation. This effect is one order of magnitude larger than the simple heterogeneity arising from boundary collision on the cylinder. Variable restitution coefficients bring the simulation closer to the general observation and allow the investigation of peening regimes with changing shot density. We compute within this model other physical quantities (impact velocities, impact angle, temperature and density profile) that are influenced by the number N of spheres.