Continuous precipitation of calcium sulfate dihydrate from waste sulfuric acid and lime

Precipitation of calcium sulfate dihydrate, gypsum, from (i) a pure sulfuric acid/lime suspension and (ii) a waste sulfuric acid/lime suspension in a continuous pilot plant in the temperature range from 40 °C to 80 °C was studied. It was observed that in the case of waste sulfuric acid with a high content of Mg²⁺ and Fe²⁺ ions, several hours after the beginning of the precipitation, partial dissolution of the product and modification of the crystals from needle‐ and plate‐like to agglomerated structures occurred. It is suggested that the secondary changes occur due to the increased concentration of Mg²⁺ and Fe²⁺ ions in the reactor. Below 60 °C, and above 70 °C plate‐like and needle‐like single crystals respectively were formed. The mean size (d₅₀) of the crystals was found to increase with increasing temperature and decrease with the initial concentration of lime. Gypsum produced between 70 °C and 80 °C is suitable for further processing for construction plaster. In a precipitation process with pure sulfuric acid only single perfect needle‐like crystals occurred. Copyright © 2005 Society of Chemical Industry     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

A new method for the determination of wax precipitation from non-diluted crude oils by fractional precipitation

Wax precipitation is one of the most important flow assurance problems. Unfortunately, experimental data are very scarce to confirm existing models for prediction of such precipitation problem. This work reports a new experimental method. Multistage fractional wax precipitation was carried out by decreasing the temperature of crude oil. No solvent dilution was used, so the effect of solvent on temperature wax precipitation was avoided. The reproducibility of the method was tested with comparable results. The precipitation curve and the wax appearance temperature were obtained for two crude oils with different chemical nature using the reported method.     

On the microhardness testing of electrically stressed poly(phenylene oxide): Polystyrene blends

Microhardness measurements have been performed on untreated (virgin) and electrically stressed, solvent‐cast laboratory‐prepared samples of pure poly(phenylene oxide) (PPO), pure polystyrene (PS), and PPO : PS polyblends with different weight proportions. Results of such measurement on untreated polyblend sample show that microhardness (H_v) increases with increase in the content of PS up to 10 wt %, which attributed to the existence of homogeneous phase morphology. However, this feature is not observable in samples containing higher content of PS. Electrical stress is found to modify considerably the mechanical property of polymer. The effect of electric field on the microhardness of such samples (PPO : PS :: 90 : 10) has been characterized by the existence of a peak. Trapping of charge carriers in electrically stressed samples imparts hardening to the polyblend up to an applied step field of 190 kV/cm. However, the excessive charging beyond this step field value destroys this characteristic. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

三(明)钢烧结厂电除尘灰的气力输送

三钢烧结厂130m^2烧结机电除尘输灰首次采用了气力输送系统。该系统由气源、输送、管路、灰库及控制五部分组成，本文介绍了系统的工作原理及运行调试情况。系统投产后，运行平稳，达到了设计要求。     

JDZ-1型固态存储雨量器降水量误差成因分析

对JDZ-1型固态存储雨量器与虹吸自记雨量计平行观测资料进行了系统分析,分析了两者存在误差的影响因素。对JDZ-1型固态存储雨量器在北方地区使用过程中存在的问题提出了解决方法,以保证和提高JDZ-1型固态存储雨量器资料质量。     

ENSO事件对松花江流域夏季降水的影响

对1951—2000年的ENSO事件对松花江流域夏季(6—8月)降水的影响进行了分析,结果显示:赤道中东太平洋海温异常与松花江流域夏季降水有很好的相关性,特别是ENSO事件出现后,El Nino事件影响年通常对应于松花江流域夏季降水偏多,La Nina事件影响年松花江流域夏季降水则较常年偏少,且二者通过了置信度α=0.05的显著性检验.这种相关性可用于进行松花江流域夏季降水的预测.     

Numerical Simulation of Internal Oxidation of Steels during Annealing Treatments

This paper presents a new model for simultaneous diffusion and precipitation of chemical elements in metallic matrices, a scheme for its numerical solution, and several applications to problems of internal oxidation. The model basically stands as an extension of the classical Wagner model for internal oxidation of steels, but is more much general in that it allows for an arbitrary number of diffusing chemical elements, an arbitrary number of precipitate phases with arbitrary compositions, dependence of diffusion coefficients and solubility products upon (time-dependent) temperature, etc., thus allowing for a much broader range of applications. As a counterpart, it is generally impossible to solve the complex, non-linear equations of the model analytically, but this can be done numerically. The simple but efficient numerical scheme proposed is based on explicit 1D finite differences. Experience has shown that this scheme, in spite of its rusticity and the restrictions it imposes on the time-step, is more efficient than more elaborate strategies based on the finite-element method. The applications presented are concerned with internal oxidation of steels during annealing processes. The model and associated numerical scheme allow for evaluation of the amounts of the various oxide precipitates in the external layer of the sheet. This opens the way, through numerical parametric studies of the influence of the process parameters and the chemical composition, to the improvement of existing treatments and the development of new steel grades.     

Oxidation behavior of 2.25Cr-1Mo steel with prior tempering at different temperatures

The oxidation behavior of a normalized 2.25Cr-1Mo steel tempered previously for 10 hr at different temperatures between 873 and 1023 K has been studied up to a maximum duration of 1000 hr in air at 773–973 K. The oxidation resistance of the steel was found to decrease significantly with the temperature of tempering. Tempering of this steel is reported to cause microstructural changes involving precipitation of Cr as carbides and a decrease in the effective (free) Cr contents, that could influence the oxidation resistance of the Cr-containing alloys. Relative compositions across the thickness of the oxide scales, as analyzed by SEM/EDX and SIMS, suggest that a less Cr-rich (and less protective) and thicker scale on the steel formed because previous tempering caused extensive depletion of free Cr.     

AGING BEHAVIOUR OF PARTICULATE REINFORCED ALUMINUM ALLOY MATRIX COMPOSITES

The process of aging precipitation in SiC_p/6061 and Al_2O_3/6061 composites were investigated. Hardness testing, differential scanning calorimetry(DSC) and transmission electron microscopy were employed. Results showed that the precipitation phase form directly along dislocation lines in the composites because the particles produce high densities of dislocations which makes vacancy densities in the composites decrease, and the main precipitation phase at peak hardness was β′ phase.