Gasification of polyethylene using steam plasma generated by microwave discharge

Gasification of polyethylene (PE) pellet was studied using atmospheric argon-steam plasma generated by microwave discharge and the feasibility of the process was examined. The experimental results showed that additional steam to argon plasma promoted the weight decrease of PE and enhanced the production of H₂, CO, CO₂ and CH₄. The results confirmed that the treatment of plastics with the steam plasma was effective to obtain synthesis gas.     

Analysis of characteristic odors from human male axillae

A number of studies concerning the analysis of axillary odors have assumed that the characteristic odor produced in the axillae is due to volatile steroids and isovaleric acid. Organoleptic evaluation of Chromatographic eluants from axillary extracts was employed to isolate the region in the chromatogram where the characteristic odor eluted. The odor of the dissolved eluant was eliminated when it was treated with base, suggesting that acids make up the characteristic axillary odor. Subsequent extraction of the pH-adjusted axillary extract in conjunction with organoleptic evaluation of the Chromatographic eluant, preparative gas chromatography, and analysis by GC-MS as well as GC-FTIR showed the presence of a number of C₆ to C₁₁ straight-chain, branched, and unsaturated acids as important contributors to the axillary odor. The major odor component is (E)-3-methyl-2-hexenoic acid. Three homologous series of minor components are also important odor contributors; these consist of the terminally unsaturated acids, the 2-methyl-C₆ to -C₁₀ acids and the 4-ethyl-C₅ to -C₁₁ acids. These types of acids have not been reported previously as components of the human axillary secretions and have not been proposed previously as part of the principal odor components in this area.     

Wear resistance of plasma coatings for a constant work of friction

We analyze the wear resistance of plasma coatings for a constant work of friction. The dependences of the wear resistance of the coatings are obtained for a broad range of loading conditions. It is shown that the minimum sensitivity to loading conditions is exhibited by the molybdenum coatings. It is also established that the wear resistance of the coatings decreases as the amplitude of displacements increases and the cyclic frequency of the tests decreases due to the intensification of fatigue processes on the surfaces. The comparative characteristics of coatings are presented. __________ Translated from Problemy Prochnosti, No. 5, pp. 94–100, September–October, 2007.     

Should we be surprised at expert system success ?

Abstract. Expert systems proliferate. They are now a usable and used tool in a variety of organizations. However, little research has been undertaken on the quantification of success or failure of expert system projects. By and large the only test carried out for expert system validation is one of comparison of the conclusions of the system with those of an expert or team of experts. While questioning the validity, this paper accepts that this method is being used and analyses whether or not the results obtained from this type of test should be a surprise. That is, what sort of results should be expected and to what extent do the reported ones live up to these expectations? Earlier research from the field of human information processing casts doubts on the success claims made for current expert systems. The implications of this research are then analysed in order to explore the possible redeeming features of expert systems which are not taken into account in such comparisons. The use of linear models as comparators for expert systems may prove beneficial.     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

人类聚居环境学对于居住区规划设计的启示

以人类聚居环境学的研究方法从若干方面对目前的居住区规划设计进行了一定的探讨,分析规划设计及建设方面目前存在的主要问题,提出以人类聚居环境学为指导的居住区规划设计理念。     

Surface characterization of PET nonwoven fabric treated by He/O2 atmospheric pressure plasma

The surface of polyethyleneterephthalate (PET) nonwoven fabric was modified by He/O₂ atmospheric pressure plasma treatment, varying plasma exposure time. The plasma treated PET surfaces have been analyzed to investigate the chemical nature and morphology of surface by X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM), respectively. The change of wettability was measured depending on plasma exposure time. XPS results indicated the presence of oxygen‐based functional groups on the PET nonwoven fabric surface after plasma treatment and oxygen content increased as exposure time increased. The mean roughness increased after 30 s exposure and further increase in exposure to 60 s led to decrease of the roughness and then again increase. The root mean square roughness followed the similar trend to mean roughness. The average difference in height, Rz, increased after plasma exposure for 30 s, while it slightly decreased after 60 s exposure. Despite of redeposition, the Rz of 90 s exposed sample increased more than two times compared with those of 30 and 60 s exposed. Wettability increased progressively up to 10 times after 90 s exposure compared with the untreated. It is attributed to the increases of hydrophilicity and surface roughness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Plasma properties of laser-ablated St target in air

Ｐｌａｓｍａｐｒｏｐｅｒｔｉｅｓｏｆｌａｓｅｒ－ａｂｌａｔｅｄＳｔｔａｒｇｅｔｉｎａｉｒＷａｎｇＸｉａｎｇ－Ｔａｉ（王象泰）；ＭａｎＢａｏ－Ｙｕａｎ（满宝元）；ＷａｎｇＧｏｎｇ－Ｔａｎｇ（王公堂）；ＦａｎＸｉ－Ｊｕｎ（樊锡君）；ＷａｎｇＪｕｎ（王军）...