Study on the difference of dispersion behavior between hydrogen and methane in utility tunnel

Compared to liquid/gas hydrogen tank, the pipeline is an economical way for hydrogen transportation. With the quick development of utility tunnel in China, hydrogen pipeline enters the gas compartment can be expected soon. However, all the safety requirements of the gas compartment in the current standards are designed for natural gas, and the applicability for hydrogen is unknown. Therefore, a series of studies were started to investigate the safety of hydrogen in utility tunnel. In this work, a real utility tunnel locates at Shanghai was selected as the physical object. A 3D numerical model was built and successfully validated by a scaled tunnel test. The model has the maximum deviation of +9.5%. After that, a comparatively study of the dispersion behavior of CH₄ and H₂ was conducted. The assumed scenario was a 20 mm small-hole leaks with gauge pressure of 1.0 MPa in the middle of the tunnel. Numerical results shown that, H₂ has a larger dispersion velocity and higher concentration, and is more dangerous compared to CH₄. The current emergency ventilation strategy of air change rate of 12 times/h is not effective enough to dilute the H₂ flammable cloud. The alarm time of the testing points shown strong linear law. There was a sharp variation in the range of 20%–100% LFL (Lower Flammable Limit), so the alarm strategy in the tunnel standards is too ideal for both CH₄ and H₂. The numerical results in the present study could provide a guidance for the design and safety management of the hydrogen tunnel.     

基准平面垂直断面法在爆破漏斗试验中的应用

系统阐述了基准平面垂直断面法在爆破漏斗试验中测量爆破漏斗体积的基本原理,并将隧道激光断面仪应用于金厂河矿1 750 m水平15^#采场底部切割巷道爆破漏斗试验爆破漏斗体积测量中。通过与传统体重法等计算法所得漏斗体积分析比较,结果表明基于隧道激光断面仪与3D Mine软件分析的基准平面垂直断面法实用性强、操作方便、结果直观可靠,达到试验预期目的。     

Industry 4.0: a supply chain innovation perspective

The Fourth Industrial Revolution – also known as Industry 4.0 (i4.0) – comprises the digitalisation of the industrial sector. This paper uses the theoretical lens of supply chain innovation (SCI) to investigate the implications of i4.0 on supply chain management. For these purposes, the method of structured content analysis is applied to more than 200 use cases of i4.0-enabled SCI introduced by both established and startup companies. i4.0-enabled SCI manifests along three dimensions: process, technology, and business architecture. The key findings of this study can be summarised as follows: first, i4.0-enabled SCI extends the initial focus on productivity improvements in SC processes towards scalability and flexibility. Second, extant i4.0 solutions rely mostly on analytics and smart things while omitting smart people technology and the human-centric approach associated with the i4.0 paradigm. Third, established companies adopt i4.0 merely to sustain their existing business architectures while startup companies radically change their operating models, relying heavily on data analytics and the platform economy. Consequently, established companies pursue a problem-driven, engineering-based approach to SCI while startup companies follow an ‘asset-light’, business-driven approach. Lastly, there are two distinct approaches to digitalising operational SC processes: platform-based crowdsourcing of standard processes and on-demand provision of customised services.     

结冰风洞校准标准研究

本文按结冰风洞制冷方式、试验对象、用途性质和试验段尺寸归纳总结了结冰风洞的类型,指出校准标准主要针对的结冰风洞类型;阐述结冰风洞空气动力流场校准可以依据的3个国内外标准;介绍SAE结冰风洞校准标准中云雾场校准的主要内容;分析研究相关标准的特点和存在的不足;提出未来我国制定结冰风洞校准标准的建议。     

公路隧道喷射混凝土套拱加固结构力学特性

为研究喷射混凝土套拱加固前后二次衬砌与混凝土套拱的受力状况,依托陕西汉中至留坝段八里关隧道,运用有限元软件建立隧道混凝土结构套拱加固分析模型,并通过现场监测获取二次衬砌与套拱间的接触压力、套拱格栅拱架钢筋应力、套拱混凝土应力,将数值模拟结果与现场测试结果相结合,得出套拱结构的一般受力变化规律。结果表明:套拱加固前衬砌结构的最不利荷载位置位于施工缝附近的拱顶、拱肩与拱脚处; 由于衬砌局部变形与温度应力的影响,套拱混凝土应力变化呈现反复“上升-下降-上升”最后趋于稳定的特点; 套拱的作用是控制二次衬砌的进一步变形,套拱施作后所承受荷载较小,套拱反作用力远小于围岩作用于衬砌的应力,在应力计算中不应将衬砌与套拱作为整体计算; 套拱结构数值模拟所得的结果与现场测试套拱结构内力(轴力、弯矩)的大小及分布相似度高,但在衬砌裂损严重部位,数值模拟所得结果误差较大,应以现场测试结果为准。     

Studying local liquid velocity in liquid–solid packed bed using the newly developed X-ray DIR technique

Combination of X-ray Digital Industrial Radiography (DIR) and Particle Tracking Velocimetry (PTV) techniques for local liquid velocity measurement (V_LL) has been newly developed and successfully applied for trickle bed reactor (TBR). The technique was validated against newly developed fiber optical probe technique. This work attempts to highlight the applicability of this newly developed technique on a liquid–solid packed bed reactor. In this work, liquid was represented by water and solids were represented by EPS beads. The EPS beads were chosen because of its low density property. Three superficial liquid velocities (V_SL) were applied to the system. The experiment was replicated four times. The digital industrial radiography (DIR) consists of a complementary metal oxide semiconductor (CMOS) digital detector and X-ray source. Results of this work suggest that the technique has been successfully applied and comparable with previous work that has been done in the literature. It also suggests that there will be a maximum measurable interstitial liquid velocity when it travel inside the packed bed. The measured V_LL can have a maximum range that is between 4 and 4.7 times that of its V_SL. For V_SL=0.42±±2%, the V_LL-Max is in between 1.7 cm/s and 1.9 cm/s, V_SL=0.84±±2%, the V_LL-Max is in between 3.6 cm/s and 4.0 cm/s, and for V_SL=1.11±±2%, the V_LL-Max is in between 4.3 cm/s and 4.8 cm/s.     

多运营商高铁隧道移动网络覆盖方案

高铁移动网络覆盖是国内三大通信运营商的一个重点,而高铁隧道内移动网络覆盖更是运营商的一大难点痛点。文章根据我国中部省份某高铁线路覆盖规划实例,采用“设备+POI+泄漏电缆”模式,即三家运营商信号源设备通过同一POI(point of interface,多系统接入平台)接入,信号输出到泄漏电缆进行隧道覆盖,隧道口场坪站安装宽频切换天线对隧道外进行延伸覆盖,通过链路预算合理布置各运营商主设备信号源,从而实现隧道到室外的无缝覆盖。最后,根据已有成熟网络覆盖解决方案,对未来5G高铁隧道移动网络覆盖方案进行了探讨。     

结合优化支持向量机与K-means++的工控系统入侵检测方法

针对工业控制系统传统单一检测算法模型对不同攻击类型检测率和检测速度不佳的问题，提出一种优化支持向量机和K-means++算法结合的入侵检测模型。首先利用主成分分析法（PCA）对原始数据集进行预处理，消除其相关性；其次在粒子群优化（PSO）算法的基础上加入自适应变异过程避免在训练的过程中陷入局部最优解；然后利用自适应变异粒子群优化（AMPSO）算法优化支持向量机的核函数和惩罚参数；最后利用密度中心法改进K-means算法与优化后的支持向量机组合成入侵检测模型，从而实现工业控制系统的异常检测。实验结果表明，所提方法在检测速度和对各类攻击的检测率上得到明显提升。     

The World robot summit disaster robotics category – achievements of the 2018 preliminary competition

The World Robot Summit is a robot Olympics and aims to be held in a different country every four years from 2020. The concept of the Plant Disaster Prevention challenge is daily inspections, checks, and emergency response in industrial plants, and in this competition, robots must carry out these types of missions in a mock-up plant. The concept of the Tunnel Disaster Response and Recovery challenge is emergency response to tunnel disasters, and is a simulation competition whereby teams compete to show their ability to deal with disasters, by collecting information and removing debris. The Standard Disaster Robotics challenge assesses, in the form of a contest, the standard performance levels of a robot that are necessary for disaster prevention and emergency response. The World Robot Summit Preliminary Competition was held at Tokyo Big Sight in October 2018, and 36 teams participated in the Disaster Robotics Category. UGVs and UAVs contended the merits of new technology for solving complex problems, using core technologies such as mobility, sensing, recognition, performing operations, human interface, autonomous intelligence etc., as well as system integration and implementation of strategies for completing missions, gaining high-level results.     

Malic acid production from renewables: a review

Malic acid derived from fossil resources is currently applied in the food and beverage industries with a medium global production capacity. However, in the transition from a fossil-based to a bio-based economy, biotechnologically produced l -malic acid may become an important platform chemical with many new applications, especially in the field of biopolymers. In this review, currently used petrochemical production routes to dl -malic acid are outlined and insights into possible bio-based alternatives for microbial l -malic acid production are provided. Besides ecological reasons, the possibility to produce enantiopure l -malic acid by microbial fermentation is the biggest advantage over chemical synthesis. State-of-the-art and open challenges concerning production host engineering, substrate choice and downstream processing are addressed. With regard to production hosts, a literature overview is given covering the leading natural production strains of Aspergillus, Ustilago and Aureobasidium, as well as Escherichia coli as the most important engineered recombinant host. The utilization of renewable substrates as an alternative to glucose is emphasized in particular as a key aspect for a competitive bio-based production. Out of the alternative substrates discussed in this review, the industrial side-streams crude glycerol and molasses seem to be most promising for large-scale l -malic acid production. © 2019 The Authors. Journal of Chemical Technology & Biotechnology published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.