Development and validation of a micro-fin tubes evaporator model using R134a and R1234yf as working fluids

This paper presents a model of shell and tube evaporator with micro-fin tubes using R1234yf and R134a. The model developed for this evaporator uses the ε-NTU method to predict the evaporating pressure, the refrigerant outlet enthalpy and the outlet temperature of the secondary fluid. The model accuracy is evaluated using different two-phase flow boiling correlations for micro-fin tubes and comparing predicted and experimental data. The experimental tests were carried out for a wide range of operating conditions using R134a and R1234yf as working fluids. The predicted parameter with maximum deviations, between the predicted and experimental data, is the evaporating pressure. The correlation of Akhavan– Behabadi et al. was used to predict flow boiling heat transfer, with an error on cooling capacity prediction below 5%. Simulations, carried out with this validated model, show that the overall heat transfer coefficient of R1234yf has a maximum decrease of 10% compared with R134a.     

Contributions of higher order terms to nonlinear waves in fluid-filled elastic tubes: strongly dispersive case

In the present work, employing the nonlinear equations of an incompressible, isotropic and elastic thin tube and the approximate equations of an incompressible inviscid fluid, and then utilizing the modified reductive perturbation technique presented by us [15] the amplitude modulation of weakly nonlinear waves is examined. It is shown that the first order term in the perturbation expansion is governed by a nonlinear Schrödinger equation and the second order term is governed by the linearized Schrödinger equation with a nonhomogeneous term. In the longwave limit a travelling wave type of solution to these equations are also given.     

纱管跳管及应对措施

通过在长期使用纱管中发现的纱管跳管的成因，提出了防止跳管的有效措施。     

定向棱镜腔平顶高斯激光束特性的研究

在XeCl准分子激光器中,采用定向棱镜作为端反射镜与平面输出镜构成激光器谐振腔,获得了近场能量分布均匀、远场能量分布高度集中的相干平顶高斯激光束输出,并具有腔镜高抗失调能力,改善了激光束质量。     

Behaviors of concrete-filled steel tubular members subjected to combined loading

The present study is an investigation on the behaviors of concrete-filled thin-walled steel tubular members subjected to combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. ABAQUS software is used in this paper for the finite element analysis (FEA). A comparison of results calculated using this modeling shows generally good agreement with test results. The FEA modeling is then used to investigate the influence of important parameters that determine the ultimate strength of the composite members under combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. The parametric studies provide information for the development of formulae for calculating the ultimate strength of the composite members subjected to combined loading.     

Neural network systems to reproduce crash behavior of structural components

The use of neural networks as global approximation tool in crashworthiness problems is here investigated. Neural networks are not only asked to return some meaningful indices of the structural behavior but also to reproduce load-time curves during crash phenomena. To contain the number of examples required for the training process, parallel subsystems of small neural networks are designed. Design points for the training process are obtained by explicit finite element analyses performed by PAMCRASH. The settlement of the points in the design domain is defined using a maximum distance concept. The procedure is applied to different typical absorption structures made of aluminum alloy: riveted tubes, honeycomb structures, longitudinal keel beam and intersection elements of helicopter subfloors.     

New rotary valves for pulse-tube refrigerators

In most used rotary valves in GM-type pulse-tube refrigerators the rotor makes heavy mechanical contact with the stator, so the valve is liable to wear, and large torques are needed. In this paper we will describe two types of valves, which have balanced forces on the rotor. In the first valve the rotor and the stator make no mechanical contact. The second type is a contact valve, like the classical valves, but the forces on the rotor are balanced in a different way. Therefore, these valves are less liable to wear, and the torques needed to rotate the valves are small.     

An improved method for magnetic identification and localization of cracks in conductors

A SQUID magnetometer can be used to measure the magnetic field produced by flaws in a two-dimensional, conducting plate carrying a current. Identification of the flaw-induced magnetic field is difficult because of the large magnetic field associated with the edges of the plate and the current in the leads that connect the plate to the power supply. We have developed a technique by which the wire and edge fields can be cancelled prior to mapping the magnetic field. In this technique, a similar unflawed conducting sheet is placed adjacent to the flawed plate, with a connection between the sheet and the plate at one edge, and with the opposite edges of the sheet and of the plate connected to the two conductors of a coaxial cable. Thus, an applied current will flow along one conductor of the cable, across the cancelling sheet, cross into the flawed plate, return along the plate, and then return to the power supply along the other conductor of the coaxial cable. As a result of this geometry, there is no magnetic field from the lead-in wires because they are coaxial, and the magnetic field due to the edges of the plate is cancelled by the opposing magnetic field of the edges in the adjacent sheet. The extent of cancellation is determined primarily by the separation between the plate and the cancelling sheet, by the thickness of the plate, and by macroscopic inhomogeneities in their electrical conductivities.     

轴向进给比对薄壁管滚珠旋压影响的有限元分析

通过有限元数值模拟方法得出滚珠旋压中薄壁管在不同凹模旋转速度条件下轴向进给比的变化规律及工件的成形规律,并对模拟结果的等效应变分布做了分析,并与实验结果进行比较,给出薄壁管滚珠旋压时进给比的选取范围.结果表明,进给比对滚珠旋压中薄壁管直径的胀缩和工件的质量有着显著的影响.另外,从计算的模具所受的三向载荷变化情况分析了模具的使用寿命.     

An Area Optimization Method for Digital Filter Design

In this paper, we propose an efficient design method for area optimization in a digital filter. The conventional methods to reduce the number of adders in a filter have the problem of a long critical path delay caused by the deep logic depth of the filter due to adder sharing. Furthermore, there is such a disadvantage that they use the transposed direct form (TDF) filter which needs more registers than those of the direct form (DF) filter. In this paper, we present a hybrid structure of a TDF and DF based on the flattened coefficients method so that it can reduce the number of flip‐flops and full‐adders without additional critical path delay. We also propose a resource sharing method and sharing‐pattern searching algorithm to reduce the number of adders without deepening the logic depth. Simulation results show that the proposed structure can save the number of adders and registers by 22 and 26%, respectively, compared to the best one used in the past.