连轧管“竹节”问题的研究

本文就各工艺参数对“竹节”的影响进行了较系统的试验。在此基础上，对连轧管“竹节”问题进行了分析，得出了“竹节”形态的基本特征；后“竹节”与轧制压力的关系；影响后“竹节”的主要工艺因素等一系列有意义的结果。对前、后“竹节”形态明显不同的原因进行了初步探讨。提出了“竹节”在线控制模型的初步设想。     

Thermal design method of bayonet-tube evaporators and condensers

The paper describes an effectiveness-NTU design method of bayonet-tube evaporators and condensers. Including the effect of the wall superheat on the shell-side film coefficient, and using an energy balance on the tube, differential equations for the steady-state fluid temperatures are formulated. Because of the nonlinear nature of the governing equations, the fourth-order Runge-Kutta method is employed to the solution of the finite difference equations. The results are iterated with the combination of integration techniques. An upper bound to the numerical error being ±5% the fluid temperature distribution as well as the exchanger effectiveness are determined, and presented as a function of the Hurd number, the number of heat transfer units and the flow arrangement. For flow entering through the inner tube, the temperature distribution displays the occurrence of a minimum at a point other than the tube-tip of the exchanger. In an extension of the analysis, an effort is made to illustrate the deviation of the results obtained by uniform film coefficient from the present study, and the differences are outlined.     

In situ polymerization and characterization of polyester‐based polyurethane/nano‐silica composites

Polyester‐based polyurethane/nano‐silica composites were obtained via in situ polymerization and investigated by Fourier‐transform infrared spectroscopy (FTIR), or FTIR coupled with attenuated total reflectance (FTIR‐ATR), Transmission electron microscopy (TEM), atomic force microscopy (AFM), an Instron testing machine, dynamic mechanical analysis (DMA) and ultraviolet‐visible spectrophotometry (UV‐vis). FTIR analysis showed that in situ polymerization provoked some chemical reactions between polyester molecules and nano‐silica particles. FTIR‐ATR, TEM and AFM analyses showed that both surface and interface contained nano‐silica particles. Instron testing and DMA data showed that introducing nano‐silica particles into polyurethane enhanced the hardness, glass temperature and adhesion strength of polyurethane to the substrate, but also increased the resin viscosity. UV‐vis spectrophotometry showed that nano‐silica obtained by the fumed method did not shield UV radiation in polyurethane films. Copyright © 2003 Society of Chemical Industry     

Effects of Working Fluid,Tubeside Enhancement and Bundle Depth on the Optimized Fin Geometry of a Horizontal Condenser Tube

A theoretical study has been made to optimize the fin geometry of a horizontal finned tube which is to be usedfor condensers that handle the vapor load of a liquid phase change cooling module.Systematic numerical calcu-lations of the vapor to coolant heat transfer have been performed for parametric values of fin height,fin spacing,vertical bundle depth and tubeside heat transfer coefficient.Three dielectric fluids (R-113,FC-72,and FC-87)at atmospheric pressure were selected as the working fluids.For a single tube with optimized fin geometry,theaverage heat flux increased in the order of FC-87,R-113 and FC-72.Both the optimum fin height and optimumfin spacing increased with increasing vertical bundle depth.     

Periodic surface modeling for computer aided nano design

Current solid and surface modeling methods based on Euclidean geometry in traditional computer aided design are not efficient in constructing a large number of atoms and particles. In this paper, we propose a periodic surface model for computer aided nano design such that geometry of atoms and molecules can be constructed parametrically. At the molecular scale, periodicity of the model allows thousands of particles to be built efficiently. At the meso scale, inherent porosity of the model represents natural morphology of polymer and macromolecule. Surface and volume operations are defined to support crystal and molecular model creation with loci and foci periodic surfaces. The ultimate goal is to enable computer assisted material and system design at atomic, molecular, and meso scales.     

管内覆丝网强化对流换热及阻力特性的实验研究

通过实验对管内覆丝网管进行了强迫对流换热和阻力特性研究。结果表明：管内覆丝网使换热明显增强，阻力也相应增长。菱形丝网对角线距离与平行边距离之比对换热效果有决定作用，丝网厚度对换热的影响比较小，而丝网网格的大小对换热几乎没有影响，在相同的泵功率和几何条件下，换热系数最大增加２１％。     

高梯度加速管的束流传输

对不同能量、不同质量数、不同初始条件的入射束和有无空间电荷效应的离子束流在高梯度加速管中的传输进行了计算，并讨论了一些影响加速管聚焦作用的主要因素，计算结果与实际情况相符。     

I．O．T．旧梦成真

该文较详细地介绍了Ｉ．Ｏ．Ｔ管的发展历程，其特点及工作方式。