Hydrocarbon-based electrode ionomer for proton exchange membrane fuel cells

The electrode ionomer is a key factor that significantly affects the catalyst layer morphology and fuel cell performance. Herein, sulfonated poly(arylene ether sulfone)-based electrode ionomers with polymers of various molecular weights and alcohol/water mixtures were prepared, and those comprising the alcohol/water mixture showed a higher performance than the ones prepared using higher boiling solvents, such as dimethylacetamide; this is owing to the formation of the uniformly dispersed ionomer catalyst layer. The relation between ionomer molecular weight for the same polymer structure and the sulfonation degree was investigated. Because the chain length of polymer varies with molecular weight and chain entanglement degree, its molecular weight affects the electrode morphology. As the ionomer covered the catalyst, the agglomerates formed were of different morphologies according to their molecular weight, which could be deduced indirectly through dynamic light scattering and scanning electron microscopy. Additionally, the fuel cell performance was confirmed in the current-voltage curve.     

Investigation on sulphonated zinc oxide nanorod incorporated sulphonated poly (1,4-phenylene ether ether sulfone) nanocomposite membranes for improved performance of microbial fuel cell

Hydrothermally prepared zinc oxide nanorods are sulphonated (S–ZnO NR) and incorporated into 15% Sulphonated Poly (1,4-Phenylene Ether Ether Sulfone) (SPEES) to improve the hydrophilicity, water uptake and ion transfer capacity. Water uptake and ion transfer capacity increased to 34.6 ± 0.6% and 2.0 ± 0.05 meq g^?1 from 29.8 ± 0.3% and 1.4 ± 0.04 meq g^?1 by adding 7.5 wt% S–ZnO NR to SPEES. Morphological studies show the prepared S–ZnO NR is well dispersed in the polymer matrix. SPEES +7.5 wt% S–ZnO NR membrane exhibits optimum performance after three-weeks of continual operation in a fabricated microbial fuel cell (MFC) to produce a maximum power density of 142 ± 1.2 mW m^?2 with a reduced biofilm compared to plain SPEES (59 ± 0.8 mW m^?2), unsulphonated filler incorporated SPEES (SPEES + 7.5 wt% ZnO, 68 ± 1.1 mW m^?2) and Nafion (130 ± 1.5 mW m^?2) thereby suggesting its suitability as a sustainable and improved cation exchange membrane (CEM) for MFCs.     

阳离子型高温酸化缓蚀剂的合成及其性能评价

针对Mannich碱型缓蚀剂存在的溶解性不好和缓蚀率不高等问题,以甲醛、环己酮和苯胺为原料,合成了一种Mannich碱型缓蚀剂CH-9,将其阳离子化后,再与丙炔醇复配,得到了阳离子型高温酸化缓蚀剂CH-10。由室内性能评价可知,CH-10在盐酸中有良好的溶解分散性;与酸液中其他添加剂如粘土稳定剂和铁离子稳定剂的配伍性良好,不会对酸化地层造成堵塞;在90℃和常压下,在20%HCl溶液中加入浓度为1%的CH-10,其对N80钢片的腐蚀速率为4.765g/(m2·h);在120℃时,浓度为2%的CH-10对N80钢片的腐蚀速率为14.30g/(m2·h),均达到了SY/T5405-1996标准中的一级标准。     

二氧化碳加氢直接合成二甲醚催化剂的研究——沉淀次序对复合催化剂结构和性能的影响

以草酸乙醇溶液为沉淀剂,采用不同的沉淀次序(并流、反加和正加)制备了CuO-ZnO-Al2O3/HZSM-5复合型催化剂,对CO2加氢直接合成二甲醚反应的催化活性顺序为:并流法催化剂>反加法催化剂>正加法催化剂。3种复合催化剂的还原温度由低到高的顺序为:并流法催化剂<反加法催化剂<正加法催化剂。在沉淀过程中,反加法和正加法均形成类胶体沉淀,相应催化剂的比表面积也较大。IR研究发现,催化剂在1101cm-1处表现Cu/Zn/Al氧化物与HZSM-5分子筛之间相互作用的IR吸收峰强度与其催化活性间存在对应关系。XRD结果表明,并流法得到的催化剂前驱体中有铜锌同形取代现象,有利于催化剂活性的发挥。     

氢型丝光沸石催化剂催化α-蒎烯合成α-松油醇

在相转移助剂苄基三乙基氯化铵(BTEAC)存在下,以氢型丝光沸石(HM)为催化剂,原料α-蒎烯经开环、重排及水合反应一步法合成了α-松油醇。研究了各种因素对α-蒎烯转化率及α-松油醇收率的影响,采用5因素4水平L16(45)进行了正交实验,得出最佳的工艺条件:反应温度80℃,w(BTEAC)=15%,m(HM)∶m(α-蒎烯)=0.6,反应时间40h,m(乙酸乙酯)∶m(α-蒎烯)=0.9。在此条件下,α-蒎烯转化率为75.2%,α-松油醇收率为42.0%。用气相色谱-质谱联用仪对反应产物进行分析,共鉴定出14种化合物,主要成分为α-松油醇、α-蒎烯、柠檬烯、桉叶油素、异松油烯、龙脑等。实验得到的α-松油醇具有光学活性,旋光值[α]=+61°,同时香气纯正,可用于制作香料。     

N-苄基丙烯酰胺的合成

以丙烯腈和苯甲醇为原料，浓硫酸作催化剂，合成了N-苄基丙烯酰胺（N-BAA）。考察了反应温度、反应时间和催化剂用量等因素对产物收率的影响，得出了最佳反应条件：n（丙烯腈）：n（苯甲醇）：n（浓硫酸）=3：1：1．2，反应时间3h，反应温度60℃。在最佳条件下，N-BAA的收率可达92％。每100g粗产物用10％氢氧化钠溶液提纯，精制产物纯度可达99．80％，熔点为64～65℃。通过红外光谱对产物结构进行了表征。     

分子筛绿色化合成技术的开发

对现有分子筛合成废液中氨氮及还原性物质的来源进行分析，确定降低排放废水中氨氮浓度及COD的方案。对现有ZRP-5分子筛制备流程进行优化，增加母液及赶胺水回用工序；建立母液浓缩装置，将钛硅分子筛及Β分子筛的合成母液及重排母液应用于ZSM-5分子筛的合成，实现废液的梯级利用。上述措施既解决了因分子筛生产废液的排放造成的环境污染，亦因废物资源化降低了ZSM-5分子筛的生产成本。     

SIMULATION STUDIES OF THE REMOVAL OF WATER FROM ETHANOL BY A CATALYTIC DISTILLATION PROCESS

A new approach based on catalytic distillation (CD) technology was proposed to remove water from ethanol. Isobutylene was introduced to react with water in the CD column. The commercial software simulation tool Aspen Plus was used to investigate the effects of key design factors such as operating pressure and temperature, reactant ratios, reflux and distillate to feed ratios, number of separation and reaction stages, and feed and reaction zone location. It was found that the CD technology offers potential advantages of reduced energy consumption and reduced capital cost over traditional approaches for the removal of water from ethanol.     

Fluorescence and IR characterization of epoxy cured with aliphatic amines

Cure reactions of the stoichiometric mixtures of diglycidyl ether of bisphenol A (DGEBA) and two very low molecular weight aliphatic polyether diamines (PED) were studied by using fluorescence and mid- and near-IR spectroscopic techniques. As the cure proceeded, the primary amine groups in PED are converted to the secondary and the tertiary amines. Near-IR spectral analysis was used to calculate the concentration of the three amine groups as a function of cure time. The decrease in the fluorescence intensity of DGEBA at about 307 nm was observed due to more effective quenching of the tertiary amine groups in PED, in comparison to the primary and the secondary amine groups. A large decrease in fluorescence intensity at 75 and 95 °C cure was observed. The amount of all the amine species was estimated from NIR spectra to shed light on the cure kinetics of PPO (polypropylene oxide) in comparison with PEO (polyethylene oxide) epoxy, as well as to explain their fluorescence behavior.The fluorescence intensity changes were correlated to the extent of epoxy reaction obtained by mid- and near-IR spectroscopy.