Plasma-assisted CO2 reforming of methane over Ni-based catalysts: Promoting role of Ag and Sn secondary metals

Carbon dioxide (CO₂) and methane (CH₄) are the primary greenhouse gases (GHGs) that drive global climate change. CO₂ reforming of CH₄ or dry reforming of CH₄ (DRM) is used for the simultaneous conversion of CO₂ and CH₄ into syngas and higher hydrocarbons. In this study, DRM was investigated using Ag–Ni/Al₂O₃ packing and Sn–Ni/Al₂O₃ packing in a parallel plate dielectric barrier discharge (DBD) reactor. The performance of the DBD reactor was significantly enhanced when applying Ag–Ni/Al₂O₃ and Sn–Ni/Al₂O₃ due to the relatively high electrical conductivity of Ag and Sn as well as their anti-coke performances. Using Ag–Ni/Al₂O₃ consisting of 1.5 wt% Ag and 5 wt% Ni/Al₂O₃ as the catalyst in the DBD reactor, 19% CH₄ conversion, 21% CO₂ conversion, 60% H₂ selectivity, 81% CO selectivity, energy efficiency of 7.9% and 0.74% (by mole) coke formation were achieved. In addition, using Sn–Ni/Al₂O₃, consisting of 0.5 wt% Sn and 5 wt% Ni/Al₂O₃, 15% CH₄ conversion, 19% CO₂ conversion, 64% H₂ selectivity, 70% CO selectivity, energy efficiency of 6.0%, and 2.1% (by mole) coke formation were achieved. Sn enhanced the reactant conversions and energy efficiency, and resulted in a reduction in coke formation; these results are comparable to that achieved when using the noble metal Ag. The decrease in the formation of coke could be correlated to the increase in the CO selectivity of the catalyst. Good dispersion of the secondary metals on Ni was found to be an important factor for the observed increases in the catalyst surface area and catalytic activities. Furthermore, the stability of the catalytic reactions was investigated for 1800 min over the 0.5 wt% Ag-5 wt% Ni/Al₂O₃ and 0.5 wt% Sn-5 wt% Ni/Al₂O₃ catalysts. The results showed an increase in the reactant conversions with an increase in the reaction time.     

A review of the existing performance verification infrastructure for micro-CMMs

The performance verification of micro-CMMs is now of intense interest because of their capability to perform length measurements in three dimensions to high accuracy with low uncertainties. Currently, verification of micro-CMMs is completed in the spirit of existing specification standards, because strict adherence to these standards is often difficult. This review aims to present and discuss verification techniques available for micro-CMMs: specification standards, existing calibrated test lengths and traceability routes that can be associated with micro-CMMs. Three specification standards used in the testing of CMMs will be considered. In addition, a wide range of calibrated test lengths are reported, and any advantages and disadvantages associated with their use are discussed. It is concluded that micro-CMMs cannot yet be verified in accordance with existing specification standards. Suggestions are made for future standardisation work required to rectify these issues.     

Multi-discharge EDM coring of single crystal SiC ingot by electrostatic induction feeding method

A new technique of EDM coring of single crystal silicon carbide (SiC) ingot was proposed in this paper. Currently single crystal SiC devices are still of high cost due to the high cost of bulk crystal SiC material and the difficulty in the fabrication process of SiC. In the manufacturing process of SiC ingot/wafer, localized cracks or defects occasionally occur due to thermal or mechanical causes resulted from fabrication processes which may waste the whole piece of material. To save the part of ingot without defects and maximize the material utilization, the authors proposed EDM coring method to cut out a no defect ingot from a larger diameter ingot which has localized defects. A special experimental setup was developed for EDM coring of SiC ingot in this study and its feasibility and machining performance were investigated. Meanwhile, in order to improve the machining rate, a novel multi-discharge EDM coring method by electrostatic induction feeding was established, which can realize multiple discharges in single pulse duration. Experimental results make it clear that EDM coring of SiC ingot can be carried out stably using the developed experimental setup. Taking advantage of the newly developed multi-discharge EDM method, both the machining speed and surface integrity can be improved.     

结冰风洞校准标准研究

本文按结冰风洞制冷方式、试验对象、用途性质和试验段尺寸归纳总结了结冰风洞的类型,指出校准标准主要针对的结冰风洞类型;阐述结冰风洞空气动力流场校准可以依据的3个国内外标准;介绍SAE结冰风洞校准标准中云雾场校准的主要内容;分析研究相关标准的特点和存在的不足;提出未来我国制定结冰风洞校准标准的建议。     

一次性使用医用手套标准解读

一次性医用手套是能够防止人们交叉感染的常用防护用品。随着新冠肺炎疫情在全球范围的迅速蔓延,疫情防控一线以及广大普通民众对一次性医用手套的需求与日俱增,其标准也受到广泛关注。本文对中国国家标准涉及一次性使用医用手套的4项产品标准进行了解读,并分析它们与国外同种产品标准间的对应关系以及重点指标的差异。     

东兴铝业嘉峪关分公司铝灰渣循环利用研究

铝灰渣是铝熔铸过程中产生的废弃物。本文主要介绍了酒钢东兴铝业嘉峪关分公司铝灰渣的产生量、排放、利用情况、化学成分及表面特征,并简要介绍了铝灰渣、铝灰的循环利用途径。     

Enhance cycling performance of LiMn2O4 cathode by Sr2+ and Cr3+ doping

Spinel LiSr_0·1Cr_0·1Mn_1·8O₄ was synthesised by high temperature solid state method in order to enhance the electrochemical performance. The LiSr_0·1Cr_0·1Mn_1·8O₄ (LSCMO) materials were characterised by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical tests. The XRD and SEM studies confirm that LSCMO had spinel crystal structure with a space group of Fd3m, and the particle of LSCMO shows irregular shape. The cyclic voltammetry data illustrated that the heavy current charge–discharge performance of LMO was improved by Sr²⁺ and Cr³⁺ doping. The galvanostatic charge–discharge of LSCMO cathode materials was measured at 1, 5, 10 and 20 C. The results indicated that LSCMO improved the capacity retention.     

澳大利亚“基于能力本位的评估”模式及对我国高职教育 质量评估的启 示

澳大利亚职业教育在全球享有较高的声誉,这与其坚持严格的"基于能力本位的评估"(competency based assessment, CBA)密不可分。介绍了澳大利亚CBA的内涵特征,并详细描述"准备评估、开发评估工具、开展评估、对评估结果进行评估"的CBA运作过程,关注评估工具的开发和后续常规系统性检查及完善,以期对我国的高等职业教育质量评估起到启示和借鉴作用。     

仪器仪表产品脉冲耐压试验要求和保护器件的选择

仪器仪表产品的脉冲耐压试验是产品型式试验、例行试验中的基本内容。通过对GB4793.1标准的整理,归纳了仪器仪表产品的脉冲耐压试验要求。通过对试验方法和设备特性的梳理,总结了特性参数,并介绍了应对脉冲耐压试验可采取的保护器件的类别及选用方法。