Corrosion behavior of T24, T92, VM12, and AISI 304 steels exposed to KCl–NaCl–K2SO4–Na2SO4 salt mixtures

The corrosion mechanisms of T24, T92, VM12, and AISI 304 steels are studied under the influence of NaCl–KCl, NaCl–Na₂SO₄, and KCl–K₂SO₄ salt mixtures in a dry air atmosphere at 650°C for 15 days. NaCl–KCl was the most aggressive deposit and AISI 304 stainless steel exhibited the highest corrosion resistance. There was no relation between the Cr content of the ferritic steels and their corrosion resistance in NaCl–KCl. In contrast, the resistance of high-Cr steels was better when exposed to NaCl–Na₂SO₄ and KCl–K₂SO₄. The high-Cr and the low-Cr steels were more susceptible to NaCl–Na₂SO₄ and to KCl–K₂SO₄, respectively.     

Corrosion of hot-dip-galvanised steel and zinc alloy-coated steel in ammonia and ammonium chloride

There are many potential causes of corrosion in animal buildings. Animals exhale large quantities of moisture into the air creating high relative humidity in the building if the moisture is not properly vented. High humidity increases the potential for condensation. In addition, ammonia may be found in large quantities in animal buildings. Ammonia is released from manure and urine. In addition, ammonium chloride is used as a nitrogen source in fertilisers. In this study, the atmospheric corrosion of hot-dip-galvanised steel and zinc alloy-coated steel such as zinc–aluminium and zinc–aluminium–magnesium has been studied in atmospheres containing different levels of ammonia. Investigations have also been conducted at different levels of ammonium chloride. The results are discussed in view of the mechanisms of corrosion of zinc and zinc alloy-coated steel in ammonia and ammonium chloride-containing environments.     

氢型丝光沸石催化剂催化α-蒎烯合成α-松油醇

在相转移助剂苄基三乙基氯化铵(BTEAC)存在下,以氢型丝光沸石(HM)为催化剂,原料α-蒎烯经开环、重排及水合反应一步法合成了α-松油醇。研究了各种因素对α-蒎烯转化率及α-松油醇收率的影响,采用5因素4水平L16(45)进行了正交实验,得出最佳的工艺条件:反应温度80℃,w(BTEAC)=15%,m(HM)∶m(α-蒎烯)=0.6,反应时间40h,m(乙酸乙酯)∶m(α-蒎烯)=0.9。在此条件下,α-蒎烯转化率为75.2%,α-松油醇收率为42.0%。用气相色谱-质谱联用仪对反应产物进行分析,共鉴定出14种化合物,主要成分为α-松油醇、α-蒎烯、柠檬烯、桉叶油素、异松油烯、龙脑等。实验得到的α-松油醇具有光学活性,旋光值[α]=+61°,同时香气纯正,可用于制作香料。     

ADN氧化剂的合成及其在推进剂中的应用

综述了ADN的合成、性质及其在推进剂中的应用，认为球形ADN具有能量高、感度低、特征信号低，对环境无污染等优点，将其作为氧化剂在高能低特征信号推进剂中有着广阔的应用前景。     

无机阻燃剂高聚合度聚磷酸铵的研制

以五氧化二磷、磷酸铵盐、尿素为原料、氨气为保护气,制备了高聚合度聚磷酸铵无机阻燃剂。考察了五氧化二磷、磷酸铵盐、尿素的用量和反应温度对聚磷酸铵平均聚合度的影响。采用端基滴定法测定了聚磷酸铵的聚合度,并用X射线衍射(XRD)法表征了聚磷酸铵的晶体结构,同时测定了聚磷酸铵的粒度和溶解度。实验结果表明,制备聚磷酸铵的最佳反应条件为:n(磷酸氢二铵)∶n(五氧化二磷)∶n(尿素)=1∶1∶0.3,反应温度280~300℃,反应时间40m in,热处理温度250~280℃,热处理时间110m in。在此条件下制备的聚磷酸铵的平均聚合度大于600,平均粒径直径小于50μm,在水中的溶解度小于0.4g;XRD表征结果表明,所合成的物质为Ⅱ型聚磷酸铵。     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

十二酰胺丙基二甲基羟乙基氯化铵与十二烷基硫酸钠水溶液的表面吸附和胶束形成

利用十二酰胺丙基二甲胺和氯乙醇反应 ,合成了十二酰胺丙基二甲基羟乙基氯化铵 (DDHA)阳离子表面活性剂 ,将其与十二烷基硫酸钠 (SDS)以不同摩尔比进行混合 ,测定了混合系统的表面张力 ,计算了单一系统和混合系统的饱和吸附量、分子最小截面积 ,表面层和胶束中 DDHA的摩尔分率及分子间相互作用参数 ,目视观察了混合系统的浑浊情况。结果表明 :在降低γcmc和 cmc方面 ,DDHA SDS混合系统有协同效应 ,表面层和胶束的组成与二组分配比有关 ,但是非对称的 ,等物质的量混合物中 ,DDHA在胶束和表面层中具有较大的摩尔分数。DDHA与 SDS在实验测定的各混合系统中都不出现混浊     

Improvement of the deflocculating power of polyacrylates in ceramic slips by small additions of quaternary ammonium salts

In this work, we examine the effect of small additions of cationic quaternary ammonium salts (QAS) of different molecular weight on the rheology of an industrial ceramic suspension deflocculated with sodium polyacrylate and sodium metasilicate. The observed shear thinning behaviors obey the typical power law of fluid rheology. In order to characterize the rheological behavior of these slurries, three new parameters are introduced: a low shear rate consistency index and two transient viscosities, distant from the equilibrium, after increasing and decreasing the shear rates. These parameters vary with polyacrylate molecular weight and on additions of small quantities of QAS, which we found to be useful for decreasing the slurry viscosity.     

延迟破胶及强制裂缝闭合技术的研究及应用

采用延迟破胶技术,在压裂施工过程中加入不同浓度的胶囊破胶剂,利用它的延缓释放特性,使植物胶压裂液耐温、耐剪切稳定性增强,并且可以在不造成压裂液的流变性、滤失性和携砂性等过早丧失的前提下高浓度使用胶囊破胶剂。该技术与常规破胶技术相比,延缓释放率达50%,能更有效地清除液体残渣,减少压裂液对储层的伤害。同时由于有延缓破胶的特性,放喷采用相应的措施,可以降低支撑剂沉降速度,形成较好的沉砂剖面,提供高的裂缝导流能力,并且可以降低滤饼和压裂液残渣的伤害。     

Synthesis, Characterization and Crystal Structure of Quaternary Complex of Gadolinium （Ⅲ）

Ａｎｕｍｂｅｒｏｆｌａｎｔｈａｎｉｄｅｔｅｒｎａｒｙｃｏｍｐｌｅｘｅｓｃｏｎ ｔａｉｎｉｎｇｈｅｔｅｒｏｃｙｃｌｉｃａｍｉｎｅｓｈａｖｅｂｅｅｎｒｅｐｏｒｔｅｄｓｉｎｃｅ1960 [1] .Ｉｎｒｅｃｅｎｔｙｅａｒｓｍｕｃｈａｔｔｅｎｔｉｏｎｈａｓｂｅｅｎｐａｉｄｔｏｑｕａｔｅｒｎａｒｙｃｏｍｐｌｅｘｅｓｏｆｌａｎｔｈａｎｉｄｅｓｂｅｃａｕｓｅｏｆｉｎ ｔｅｒｅｓｔｉｎｇｓｔｒｕｃｔｕｒｅ ,ｃｏｏｒｄｉｎａｔｉｏｎｍｏｄｅ ,ｃｏｍｐｅｔｉｔｉｏｎｒｅ ａｃｔｉｏｎａｎｄｐｒｏｐｅｒｔｙ[2～ 9] .ＥＳＲｃａｎｅ…