岩石物理横波速度曲线计算技术

横波速度是地震勘探中的重要参数。针对实际生产中缺乏横波速度测井曲线资料，利用经验公式计算精确度不高的问题，通过对横波速度计算理论模型的研究分析，选择Blot-Gassman模型法，利用岩石矿物成分、流体成分、孔隙度及密度等测井曲线进行横波速度测井曲线的计算，并对横波速度计算技术和流程进行研究。在实际工区进行了横波速度曲线计算，计算结果与实测横波吻合程度较高，误差小于10％，该技术在储层和流体识别预测的应用中取得了较好效果。     

SJ—YⅡ—5型高爆速高威力水胶炸药的研制

文章简要分析了我国目前在中硬岩石爆破中工业炸药的使用情况，介绍了山西兴安化学材料厂新研制的一种适用于硬岩爆破的高爆速、高威力水胶炸药新品种，对其性能、爆破效果、经济实用性和安全性等进行了阐述。     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

一种改进的交错脉冲解速度模糊方法

研究了脉冲多普勒气象雷达中用于解速度模糊的交错脉冲方法，理论分析了时域脉冲对处理中速度估计公式的局限性，同时对该公式进行了修正。仿真结果表明，改进的交错脉冲方法具有更好的解速度模糊性能，而且易于实时处理。     

Constant thrust programming for a multistage rocket flown in vacuum with a given initial/final thrust-to-weight ratio in an arbitrary stage

The burn time and burnout velocity of a multistage rocket flown vertically in vacuum with constant thrust tangential to the flight path and a prescribed initial/final thrust-to-weight ratio in an arbitrary stage have been determined. The present paper also deals with optimal staging under given conditions of flight.     

建立速度模型的层析成像方法研究

针对目前叠前深度偏移速度模型建立中，全局反演的层析成像方法存在稳定性和走时拾取困难，以及局部反演的偏移速度分析大多存在假设条件过于苛刻等问题，通过分析，提出了利用地震同相辅的多种信息进行层析反演，并在反演中加入富有地质含义的倾角信息以增加反演过程的稳定性和收敛速度，利用类似于叠加速度谱的斜率速度谱来拾取地震同相轴的斜率，抛开了层位反演要求拾取同一同相轴这一实际应用难度很大的条件，使拾取方便，算法稳定。通过理论试算，证明了本方法的有效性。     

首钢外购焦炭质量恶化后的高炉生产实践

针对焦炭质量劣化的状况，高炉操作以活跃炉缸为主，从上下部调剂入手，采取疏导煤气、控制合理的实际风速和鼓风动能、缓解焦炭在高温区的粉化等措施，有效地改善了高炉的顺行状况，并逐步恢复高炉指标。     

Terminal velocity of non-spherical particles falling through a Carreau model liquid

A procedure has been proposed for the estimation of the terminal falling velocity of non-spherical particles moving in a Carreau model fluid in the transition flow region. The procedure is based on a modification of the relationship formerly developed for the fall of spherical particles including the particle dynamic shape factor. The suitability of the proposed procedure has been confirmed by good agreement between experimental and calculated terminal falling velocity data. In the experiments, the terminal falling velocity of short cylinders and rectangular prisms in polymer solutions of different measure of shear thinning and elasticity has been measured.     

Drag coefficient of flow around a sphere: Matching asymptotically the wide trend

An empirical relationship of drag coefficient of flow around a sphere is developed for the entire range of Particle Reynolds numbers reported in the literature from Stokes regime to the condition when turbulent boundary layer prevails. The relationship is obtained using an approach to match asymptotically the wide trend of drag coefficient. The matching approach, which relies on dividing the wide trend into smaller segments that can be combined into an overall relationship, employs regression techniques and thus warrants the best-fit accuracy results. The relationship is calibrated with experimental data available in the literature covering the entire range for Reynolds numbers up to ~ 10⁶. For Reynolds values greater than 10⁶, the relationship renders a drag coefficient of 0.2. The performance of the relationship is tested and compared with other suitable models found in the literature. This relationship is also transformed into an explicit expression for settling velocity calculations.