Synthesis and performance evaluation of a new drag reducer based on acrylamide/12-allyloxydodecyl acid sodium

Hydraulic fracturing with slickwater is a field-proven stimulation technology used in tight reservoirs. Because of the high pumping rate associated with slickwater fracturing, drag reduction (DR) is critical in minimizing pressure drop and the success of oilfield operations. In this paper, a new type of drag reducer (SPR) was synthesized with acrylamide and 12-allyloxydodecyl acid sodium, and its drag reduction performance was evaluated. The results showed that the new drag reducer features low molecular weight, fast-dissolving rate and low interfacial tension. The algorithm of estimating the drag reduction rate of non-Newtonian fluid SPR was proposed and validated. Empirical or semianalytical models for estimating the friction ratio (σ) or friction factor (λ or f) were used to simulate the turbulence behavior of the SPR drag reducer under different Reynolds numbers (Re). The modified Virk's correlation could accurately model the turbulent behavior of the SPR drag reducer. A unified calculation formula was established in this study for different pipe diameters.     

Diffusional behavior of multi-arm star polymers by H pulsed field gradient spin-echo NMR method

The diffusional behavior of multi-arm star-shaped p(tBMA) was investigated in a concentration range from dilute to semidilute region with ¹H pulsed field gradient spin-echo NMR (PFGSE-NMR). An 142-arm star-shaped p(tBMA) showed two diffusional mode, which reflected the coexistence of liquid ordering phase and liquid phase near the ordering transition. On the other hand, for star-shaped p(tBMA) with 55 arms showed a single diffusional relaxation in all concentration ranges during observation time. In the semidilute region, the relationship between the diffusion coefficient against the polymer concentration was affected strongly not only the arm number but also liquid ordering structure.     

新型刮刀钻头的设计及现场试验研究

在理论分析的基础上，综合PDC钻头和刮刀钻头的优点，设计了一种新型的刮刀钻头，并进行了现场试验。现场试验结果表明，该钻头运转平稳，采用低钻压、高转速，钻进速度快，井眼规则通畅，有较明显的防斜作用，该种钻头的推广应用对提高钻井工程的整体效益具有十分重要的意义。     

一种新型的转炉炉底车

本文介绍了一种作业效率高、省时省力新型的转炉炉底车，其特点是转盘转动灵活，炉底车上项盘径向任意方向均能平稳倾斜一定角度，以保证炉底圆周所受项力均匀可靠，满足炉底安装要求。     

On the boundary-layer control through momentum injection: Studies with applications

The concept of moving surface boundary-layer control, as applied to a Joukowsky airfoil, is investigated through a planned experimental programme complemented by numerical studies. The moving surface was provided by rotating cylinders located at the leading edge and/or trailing edge as well as top surface of the airfoil. Results suggest that the concept is quite promising, leading to a substantial increase in lift and a delay in stall. Depending on the performance desired, appropriate combinations of cylinder geometry, location and speed can be selected to obtain favourable results over a wide range of angle of attack. Next, effectiveness of the concept in reducing drag of bluff bodies such as a two-dimensional flat plate at large angles of attack, rectangular prisms and three-dimensional models of trucks is assessed through an extensive wind tunnel test-programme. Results show that injection of momentum through moving surfaces, achieved here by introduction of bearing-mounted, motordriven, hollow cylinders, can significantly delay separation of the boundary-layer and reduce the pressure drag. The momentum injection procedure also proved effective in arresting wind-induced vortex resonance and galloping type of instabilities. A flow visualization study, conducted in a closed-circuit water tunnel using slit lighting and polyvinyl choride tracer particles, adds to the wind-tunnel and numerical investigations. It shows, rather dramatically, the effectiveness of the moving surface boundary-layer control (MSBC). The Sabita Chaudhury Memorial Lecture The models were fabricated in the Mechanical Engineering Workshop. The assistance of M/s E Abell, P Hurren and D Camp in the design and construction of the models is gratefully acknowledged. The investigation was supported by the Natural Sciences and Engineering Research Council of Canada, Grant No. A-2181.     

球头碗球面加工组合机床设计

根据球面形成原理,利用铣刀和工件的两个圆运动,合成球头碗的不完整内球面。采用组合机床,结构简单,调整、维护方便,主轴弹性卡头便于工件装卸。对零件尺寸、形状和位置误差进行了分析。通过对铣刀和主轴电机的变频调速,找出最佳切削参数,实现了内球面的高效率高精度加工。     

多排数翅片管空冷器风阻特性的数值模拟

本文对多排数翅片管空冷器空气侧的风阻特性进行了数值模拟.利用商用软件Fluent进行数值计算,结合经验公式和已有的实验数据,分析了不同入口风速下,阻力的变化规律以及流动阻力和温度变化对模拟计算的影响.     

油溶性减阻功能聚合物的研制

介绍了以混合α-烯烃为原料,制备了具有减阻功能的共聚物。讨论了催化剂浓度、聚合温度、预聚合时间、原料单体中杂质含量对共聚物特性粘度和转化率的影响。试验表明,在较低的催化剂浓度和预聚合温度下,能得到较高分子量的聚合物。气相色谱法和DSC法测定其组成和单体混合物的组成基本一致,表明共聚物是一种无规的梳状结构聚合物。该聚合物达到较高特性粘度时,能获得较好的减阻率。     

不锈钢网架(壳)技术及其应用

本文总结了多年来不锈钢网架的研究成果 ,并介绍了部分不锈钢网架的工程应用     

Intermolecular interactions and formation of the hydration sphere in phosphonic acid model systems as an approach to the description of vinyl phosphonic acid based polymers

Molecular model systems based on propyl phosphonic acid (ppa) were studied by means of density functional theory calculations in order to describe the acid-acid interaction and the formation of the hydration sphere. The formation of ppa dimers is reported and the energetic difference between two dimer structures is presented. The hydration sphere of ppa was represented by model systems ppa(H₂O)_n, for which the system with n=4 formed the first hydration sphere (h¹), while n=7 can be considered a good approximation to the complete inner hydration sphere around the phosphonic acid group. The study of the ppa-H⁺ (H₂O)_n model systems showed an interesting structural behavior comparatively to the ppa(H₂O)_n systems. The protonated acids exhibited equivalent phosphorous-oxygen bonds and a general molecular structure is proposed to represent these protonated species.