Synthesis and performance evaluation of a new drag reducer based on acrylamide/12-allyloxydodecyl acid sodium

Hydraulic fracturing with slickwater is a field-proven stimulation technology used in tight reservoirs. Because of the high pumping rate associated with slickwater fracturing, drag reduction (DR) is critical in minimizing pressure drop and the success of oilfield operations. In this paper, a new type of drag reducer (SPR) was synthesized with acrylamide and 12-allyloxydodecyl acid sodium, and its drag reduction performance was evaluated. The results showed that the new drag reducer features low molecular weight, fast-dissolving rate and low interfacial tension. The algorithm of estimating the drag reduction rate of non-Newtonian fluid SPR was proposed and validated. Empirical or semianalytical models for estimating the friction ratio (σ) or friction factor (λ or f) were used to simulate the turbulence behavior of the SPR drag reducer under different Reynolds numbers (Re). The modified Virk's correlation could accurately model the turbulent behavior of the SPR drag reducer. A unified calculation formula was established in this study for different pipe diameters.     

Amine-containing olefin copolymer with CO2-switchable oil absorption and desorption

Global decrease in crude oil resources and frequent crude oil leaks cause the energy crisis and ecological pollution. The absorption and release of leaked crude oil through absorption materials are a necessary process for environmental protection and recycling. In this article, a CO₂-responsive olefin copolymer was obtained by copolymerization of styrene and an amine-containing olefin monomer. The structure of resultant copolymer was characterized by FTIR; thermal properties and CO₂-responsive morphology changes were determined by DSC/TGA and SEM, respectively. Copolymers had certain absorption capacity for toluene with absorption rate up to 180.0%. The absorbed toluene could be released upon CO₂ stimulation with desorption rate up to 84.6%. The CO₂-responsive copolymer could be regenerated through a simple heating process and showed stable absorption–desorption performance even after being recycled for 4 times. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47439.     

High‐performance thermosets with tailored properties derived from methacrylated eugenol and epoxy‐based vinyl ester

A renewable chemical, eugenol, is methacrylated to produce methacrylated eugenol (ME) employing the Steglich esterification reaction without any solvent. The resulting ME is used as a low‐viscosity co‐monomer to replace styrene in a commercial epoxy‐based vinyl ester resin (VE). The volatility and viscosity of ME and styrene are compared. The effect of ME loading and temperature on the viscosity of the VE–ME resin is investigated. Moreover, the thermomechanical properties, curing extent and thermal stability of the fully cured VE–ME thermosets are systematically examined. The results indicate that ME is a monomer with low volatility and low viscosity, and therefore the incorporation of ME monomer in VE resins allows significant reduction of viscosity. Moreover, the viscosity of the VE–ME resin can be tailored by adjusting the ME loadings and processing temperature to meet commercial liquid molding technology requirements. The glass transition temperatures of VE–ME thermosets range from 139 to 199 °C. In addition, more than 95% of the monomer is incorporated and fixed in the crosslinked network structure of VE–ME thermosets. Overall, the developed ME monomer exhibits promising potential for replacing styrene as an effective low‐viscosity co‐monomer. The VE–ME resins show great advantages for use in polymer matrices for high‐performance fiber‐reinforced composites. This work is of great significance to the vinyl ester industry by providing detailed experimental support. © 2018 Society of Chemical Industry     

Preparation and polymerization of isopimaric acid derivatives

Isopimaric acid is a typical rosin compound and can account for 30% of the total mass of slash pine rosin. The molecular structure of isopimaric acid derivatives features an unsaturated double bond at the C13 position, opening up the possibility of their industrial polymerization. In this study, isopimaric acid (95.4%), methyl isopimarate (99.5%), and allyl isopimarate (95.1%) were prepared as highly pure monomers. New experimental results are presented and mechanisms based on the investigation of free-radical polymerization under UV irradiation are proposed. New rosin monomers for potential value-added utilization of woody biomass are also identified. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47817.     

丙烯酸/α-甲基丙烯酸/丙烯酰胺共聚物智能水凝胶的合成及评价

由丙烯酸（AA）、α-甲基丙烯酸（MAA）和丙烯酰胺（AM）合成了具有很好DH敏感性和一定温度敏感性的智能水凝胶，考察了合成温度、丙烯酰胺、交联剂和引发剂用量对制备的水凝胶溶胀性能的影响。结果表明，在60℃下，单体从和MAA用量分别为100mmol和75mmol时，单体AM、交联剂和引发剂用量分别为反应物总质量的32．8％、0．2％和0．4％时，制备的水凝胶溶胀性能最好。考察了介质的离子浓度、pH值和温度对水凝胶溶胀比的影响，结果表明，离子浓度越大，水凝胶的溶胀比越小；水凝胶具有一定的DH可逆性。     

N-苄基丙烯酰胺的合成

以丙烯腈和苯甲醇为原料，浓硫酸作催化剂，合成了N-苄基丙烯酰胺（N-BAA）。考察了反应温度、反应时间和催化剂用量等因素对产物收率的影响，得出了最佳反应条件：n（丙烯腈）：n（苯甲醇）：n（浓硫酸）=3：1：1．2，反应时间3h，反应温度60℃。在最佳条件下，N-BAA的收率可达92％。每100g粗产物用10％氢氧化钠溶液提纯，精制产物纯度可达99．80％，熔点为64～65℃。通过红外光谱对产物结构进行了表征。     

Preparation of glucose oxidase immobilized in different carriers using radiation polymerization

Glucose oxidase (EC 1.1.3.4) was immobilized on different polymeric materials using different immobilization techniques (entrapping by γ‐irradiation, and covalent binding using epichlorohydrin). Studies were carried out to increase the thermal stability of glucose oxidase (GOD) for different applications. The activity and stability of the resulting biopolymers have been compared with those of free GOD. The effect of different polyvinyl alcohol/polyacrylamide (PVA/PAAm) compositions of the copolymer carrier on the enzymatic activity of the immobilized GOD was studied. The maximum enzymatic activity was obtained with the composition ratio of PVA/PAAm of 60:40. The behaviour of the free and immobilized enzyme was analysed as a function of pH. A broadening in the pH profile (5.5–8) was observed for immobilized preparations. The activity and stability of the resulting biopolymers produced by immobilization of GOD onto different carriers have been compared, in both aqueous and organic media, with those of the free GOD. The enzyme's tolerance toward both heat and organic solvent was enhanced by immobilization onto polymers. The addition of different concentrations of organic solvents (10–50%, v/v) to the enzyme at higher temperature (60 °C) was found to stabilize the enzyme molecule. The strongest stabilizing effect on the enzymatic activity was achieved at a concentration of 10%. Copyright © 2005 Society of Chemical Industry     

N-羟甲基丙烯酰胺的合成

对N－羟甲基丙烯酰胺（NAM）的合成工艺做了进一步的研究。结果表明：在丙烯酰胺：甲醛＝1∶1．05（mol比），碱性催化剂存在下，70℃反应3h。转化率可达99％。产品质量稳定，反应液可不经分离直接用作交联剂，降低了生产成本。并提出用固含量法测定溶液中的NAM含量，简易可靠。     

不饱和单体熔融接枝PP体系中引发剂的选择

本文选择了过氧化异丙苯、过氧化苯甲酰、二叔丁基过氧化物三种引发剂进行实验。比较了三种引发剂的基本性能。讨论了引发剂种类及用量对接枝反应的影响，并研究了三种引发剂对ＰＰ降解及对接枝物外观颜色的影响。     

Water-soluble copolymers: 22. Copolymers of acrylamide with 2-acrylamido-2-methylpropanedimethylammonium chloride: Aqueous solution properties of a polycation

The viscometric, turbidimetric and potentiometric properties of copolymers of acrylamide (AM) with 2-acrylamido-2-methylpropanedimethylammonium chloride (AMPDAC) were studied in aqueous solutions. The AMPDAC polymers exhibit poor salt tolerance and large, negative viscosity/temperature coefficients. Furthermore, the polymers were found to be sensitive to changes in pH. The AMPDAC polymers undergo phase separation in the presence of dianions as a function of temperature and AMPDAC composition.