Analysis of suitability of TPP ash-slag waste as materials for hydrogen fuel storage

The current trends in energy were described, the main of which is the use of alternative energy sources, especially hydrogen. The most common methods of hydrogen accumulation were proposed: accumulation of compressed gaseous hydrogen in high-pressure tanks; accumulation of liquid hydrogen in cryogenic tanks; storing hydrogen in a chemically bound state; accumulation of gaseous hydrogen in carriers with a high specific surface area. Based on the combination of advantages and disadvantages, the most promising methods of accumulation were selected: storage of liquid hydrogen and storage of hydrogen in carriers with a high specific surface area. The main requirement for materials for hydrogen storage by these methods was revealed – a high specific surface area. Prospects for the development of waste-free low-emission technologies due to the recycling of secondary raw materials and the development of low-temperature technologies for the synthesis of functional and structural materials were substantiated. The applicability of large-scale ash and slag waste from coal-fired thermal power plants as a raw material for obtaining materials by low-temperature technologies was shown. The traditional ways of using ash and slag waste as a raw material, active additive and filler in the production of cements were described. Modern technologies for the production of innovative materials with a unique set of properties were presented, namely carbon nanotubes, silica aerogel and geopolymer materials. The prospect of using geopolymer matrices as a precursor for the synthesis of a number of materials was described; the most promising type of materials was selected – geopolymer foams, which are mainly used as sorbents for purifying liquids and gases or accumulating target products, as well as heat-insulating materials. The possibility of obtaining products of any shape and size on the basis of geopolymer matrices without high-temperature processing was shown. The special efficiency of the development of the technology of porous granules and powders obtained from a geopolymer precursor using various methods was substantiated. The obtained granules can be used in the following hydrogen storage technologies: direct accumulation of hydrogen in porous granules; creation of insulating layers for liquid hydrogen storage units.     

碳脱氧在钢包顶渣改质中的应用

 为了进一步降低夹杂物缺陷并提高产品质量,基于碳脱氧进行了钢包顶渣改质的研究。冷轧产品的生产工艺为铁水预处理→转炉→RH精炼→连铸,为减少钢中夹杂物质量分数,需要进行钢包顶渣改质,同时降低钢包顶渣TFe质量分数。采用粒碳部分替代铝渣球的方法进行基于碳脱氧工艺的钢包顶渣改质,试验结果表明,顶渣改质效果良好,在顶渣TFe质量分数、中间包钢水游离氧明显降低的同时铸坯中Al₂O₃夹杂物得到优化;“30 kg粒渣+铝渣球”工艺降低生产成本5.16元/t(钢)。     

济阳坳陷下古生界潜山油气藏特征及成藏模式

济阳坳陷下古生界潜山具有多样性、复杂性的特点，潜山差异性的形成演化、油气成藏主控因素和控藏模式不明确，严重制约了该区潜山油气勘探。在潜山分类的基础上，综合利用系统恢复、分类对比和典型解剖等方法，揭示了济阳坳陷下古生界不同类型潜山的形成演化过程和油气成藏主控因素差异性，分类建立了油气成藏模式。研究表明，济阳坳陷下古生界主要发育高位新盖侵蚀残丘潜山、中位古盖拉张断块潜山、中位新古盖拉张剪切断块潜山、中位中古盖挤压拉张断块潜山和低位古盖拉张滑脱断块潜山5种潜山类型。不同类型潜山的形成演化和油气成藏各具特色，其中，高位新盖侵蚀残丘潜山的发育受隆升、侵蚀作用控制，油气成藏主要受控于油源和盖层条件，表现为"单向供烃、砂体-不整合岩溶体联合输导、残丘控藏"的成藏模式；中位古盖拉张断块潜山的发育受掀斜、断裂作用控制，油气成藏主要受控于储集条件，表现为"单向供烃、顺向断层输导、反向断层控藏"的成藏模式；中位新古盖拉张剪切断块潜山的发育受反转、翘倾和走滑切割作用控制，油气成藏主要受控于输导条件，表现为"多源供烃、断溶体立体输导、断裂控藏"的成藏模式；中位中古盖挤压拉张断块潜山的形成受强烈挤压、拉张滑脱作用控制，油气成藏主要受控于储集条件，表现为"多源供烃、断缝体输导、断褶控藏"的成藏模式；低位古盖拉张滑脱断块潜山的形成受强烈拉张滑脱作用控制，油气成藏主要受控于输导条件，表现为"顶部供烃、断缝体输导、断裂控藏"的成藏模式。     

Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.     

大庆长垣以东地区深层天然气输导特征及成藏

大庆长垣以东地区深层天然气输导通道主要由断裂、不整合面和砂体构成。该区砂体横向分布不稳定，物性差，不是天然气侧向长距离运移的输导通道，但可以起到衔接输导作用。输导通道时该区天然气成藏与分布起到了重要控制作用，主要表现在断裂将天然气输导致上覆不同储集层中聚集成藏。不整合面和砂体将天然气输导到四周古隆起上聚集成藏。沿断裂输导的天然气形成以断层为主的构造气藏。沿不整合面和砂体输导的天然气形成以地层及岩性为主的气藏。沿断裂输导运移聚集的天然气在剖面上呈串多层分布，沿不整合面和砂体输导运移聚集的天然气在平面上呈环状分布。     

同沉积压扭断层在柴达木盆地西部南区油气成藏中的意义

柴达木盆地西部南区逆断层断面产状呈上陡下缓的铲式特征,生长系数变化在1.3~2.5之间,断距纵向上向浅层逐渐变小和横向上向一个方向逐渐增大,总体表现为典型的同沉积压扭断层。指出该断层演化主要经历了同生冲断期、褶皱发育期、平静期及二次活动期4个阶段,长期活动的NWW向主干断层除控制构造带的展布格局外,还控制着烃源岩、储集层、盖层及其组合的空间发育,同时还有效地沟通着源岩与圈闭并成为有效输导体系的一部分,近N S向展布的次级断层决定着局部构造的发育特点,与NWW向断层联合控制着油气的局部富集。     

2.5GHz低相位噪声CMOS LC VCO的设计

用0 .35μm、一层多晶、四层金属、3.3V的标准全数字CMOS工艺设计了一个全集成的2 .5 GHz L C VCO,电路采用全差分互补负跨导结构以降低电路功耗和减少器件1/ f噪声的影响.为了减少高频噪声的影响,采用了在片L C滤波技术.可变电容采用增强型MOS可变电容,取得了2 3%的频率调节范围.采用单个16边形的对称片上螺旋电感,并在电感下加接地屏蔽层,从而减少芯片面积,优化Q值.取得了在离中心频率1MHz处- 118d Bc/ Hz的相位噪声性能.电源电压为3.3V时的功耗为4 m A.     

反转构造的反转程度及其与油气聚集的关系

结合典型反转构造地震剖面，分析了断层型和褶皱型两类反转构造的反转程度，上下皆正断层型和向形褶皱型反转构造的反转程度轻微；上逆下正断层型和透镜形褶皱型反转构造的反转程度中等；上下皆逆断层型和背形褶皱型反转构造的反转程度强烈。分析了反转构造的反转程度与油气聚集的关系，处于轻微反转程度的上下皆正断层型反转和向形褶皱型反转，以及处于强烈反转程度的上下皆逆断层型反转和背形褶皱型反转不利于油气聚集；处于中等反转程度的上逆下正断层型反转和透镜形褶皱型反转类型有利于油气聚集成藏。     

一种估算单桩经济直径的方法

在滩海油田开发过程中,经常需要设立立管桩,在环境荷载的作用下,立管桩顶部会发生位移,较大的位移对立管及栈桥的安全很不利,因此需要合理确定单桩的直径。埕岛油田在确定单桩直径时引入了经济直径的概念,文章对经济直径的原理进行了分析,给出了桩顶位移和桩径经济指数计算公式,并举例进行了计算,得出了桩径与桩顶位移及桩径经济指数的关系曲线, 进而求得经济桩径的取值范围。文章还对该方法的优缺点进行了分析。