Thermal and thermoelastic properties of fast extrusion furnace (FEF) carbon black loaded SBR vulcanizates

The effect of FEF carbon black as filler on the thermal capacity c, diffusivity a, and thermal conductivity λ, of styrene butadiene rubber (SBR) composites in the temperature range 300–420 K was studied. The filler strongly increases the thermal diffusivity, whilst strongly decreasing the thermal capacity and the thermal conductivity (except at high FEF content ≥80 phr). The influence of the filler on the thermoelastic behaviour of the same composites was also investigated. It was found that the thermoelastic temperature change (ΔT) increased with carbon black concentration as well as the entropy change per unit extension.     

Pressure Response through Valve for Continuous Oil-Water Separation Based on a Flexible Superhydrophobic/Superoleophilic Thermoplastic Vulcanizate Film

Highly efficient oil-water separation shows urgent demand in industrial applications, especially in oil-spill accidents and organic solvent separation. Herein, a novel method is proposed for continuous oil-water separation by a pressure response through valve, which is loaded in a flexible convolute superhydrophobic/superoleophilic film based on low-density polyethylene (LDPE)/ethylene-propylene-diene terpolymer (EPDM) thermoplastic vulcanizate (TPV). The superhydrophobic/superoleophilic LDPE/EPDM TPV film (with contact angles of oil and water are 0° and 161.9°± 2.2°) is prepared only via a molding process where sandpaper is used as the template. The superhydrophobic/superoleophilic property of the TPV film shows robust performance in the activity endurance test. More importantly, the flexible LDPE/EPDM TPV film can be easily rolled up and loaded in through valve, which is the pressure response channel in oil-water separation. The typical separation pressure of oil and water is 3.01 and 6.17 kPa, which means the oil can be completely separated from the oil-water mixture under proper pressure in the pressure response through valve.     

填料对反-1,4-聚异戊二烯性能的影响

研究了填料对反－1，4－聚异戊二烯（TPI）硫化胶和混炼胶的物理机械性能和结晶性能的影响。结果表明，在TPI中加入填料后，其硫化胶的300％定伸应力随填料用量的增加而增加，拉伸强度则在填料用量为20份时达到最大值；加入填料同时能降低TPI混炼胶的结晶度，填料用量增加，TPI混炼胶的结晶下降；且填料增强效果越好，结晶度下降越大。     

Natural rubber–ethylene‐propylene‐diene rubber covulcanization: Effect of reinforcing fillers

Filled covulcanizates of elastomer blend comprising natural rubber (NR) and ethylene‐propylene‐diene rubber (EPDM) of commercial importance were successfully prepared by using a multifunctional rubber additive; namely, bis(diisopropyl)thiophosphoryl disulfide (DIPDIS). A Two‐stage vulcanization technique further improved the physicochemical properties of the blend vulcanizates by restricting, through the formation of polar rubber bound intermediates, the migration of curative and filler from lower to highly unsaturated rubber. Scanning electron microscopy studies indicate homogeneity and coherency in the morphology of the two‐stage vulcanizates. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1001–1010, 2002; DOI 10.1002/app.10361     

甲基丙烯酸锌在NBR／木质素中的应用

研究了α－甲基丙烯酸锌（ＭＡＡ－Ｚｎ）对ＮＢＲ／木质素（１００／１００，质量比）硫化胶性能的影响。结果表明，加入１．５～５．０份ＭＡＡ－Ｚｎ，可提高硫化胺的１００％的定伸应力，硬度和抗压缩永久变形能力，但对其他力学性能影响甚微，经分析可知，ＭＡＡ－Ｚｎ还可以降低硫化反应活化能，提高硫化胶的交联密度和耐热老化性能。     

Recycling of ethylene propylene diene monomer (EPDM) waste. III. Processability of EPDM rubber compound containing ground EPDM vulcanizates

The rheological behavior of ethylene propylene diene monomer (EPDM) compounds containing ground EPDM waste (W‐EPDM) of known composition was studied by using a Monsanto processability tester in a temperature range of 90–110°C and a shear rate range of 306.7–1533.24 s^?1. It is found that the shear viscosity decreases slightly with increasing W‐EPDM loading because of wall slip that results from the migration of lubricants from the W‐EPDM. The addition of W‐EPDM to raw EPDM results in a decreased die swell at all temperatures and shear rates. SEM photomicrographs of the EPDM extrudate surface show improved surface smoothness and reduced extrudate distortion when EPDM is blended with W‐EPDM. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 2204–2215, 2003     

评价影响丁苯橡胶硫化胶性能的因素

为理解和正确执行丁苯橡胶（ＳＢＲ）１５００系列硫化胶性能评价的国家标准及为修订标准做必要准备，在现有实验室条件下，做了４个方面的工作：一是混炼温度对硫化胶性能的影响。试验表明：混炼温度在５０℃±５℃对硫化速度无明显影响，但随着混炼温度的升高，硫化２５ｍｉｎ的３００％定伸应力有升高趋势；二是硫化室温对硫化胶性能的影响。试验表明，室温对硫化胶影响不明显，但恢复时间Ｔ＿Ｒ的长短会直接影响硫化胶的物性，尤其对硫化２５ｍｉｎ的３００％定伸应力的影响是敏锐的，应引起足够重视；三是硫化时间对硫化胶性能的影响。试验推断Ｔ＿Ｂ的长短对硫化２５ｍｉｎ的３００％定伸应力的影响是举足轻重的，硫化时间（３５±２）ｍｉｎ对硫化胶性能影响不大；四是硫化温度对硫化胶性能的影响。试验指出，在１４５℃±１℃下，硫化２５ｍｉｎ的３００℃定伸应力相差３．３ＭＰａ，在１４５℃±０．５℃下，相差１．７ＭＰａ，由于差异会直接影响产品等级的判定，因此，国际标准规定硫化温度控制在１４５℃±０．５℃是十分必要的。     

炭黑与橡胶模量及磨耗的相关性研究

依据炭黑可以影响硫化橡胶模量和磨耗的事实，通过制备几种不同炭黑含量的硫化橡胶。对高结构、高耐磨的N339炭黑填充的硫化橡胶模量及各种条件下的磨耗进行测定，分析炭黑用量与模量、磨耗相互之间的关系．     

三元乙丙橡胶/聚丙烯热塑性硫化胶细观力学数值模拟分析Ⅱ.三元乙丙橡胶结构对细观力学性能的影响

通过建立三元乙丙橡胶(EPDM)/聚丙烯(PP)热塑性硫化胶(TPV)的细观尺寸多颗粒随机分布的RVE模型,研究了分散相EPDM粒子形状及大小、间距对TPV应力和弹性模量的影响。结果表明,在分散相EPDM体积分数不变的条件下,EPDM粒子形状越接近圆形,TPV的应力值越低,EPDM粒径的减小可提高TPV的弹性模量;EPDM粒子间距增大,TPV的应力值下降,TPV中EPDM体积分数越高,其应力值受EPDM粒子间距的影响越显著。