Corrosion behavior of under‐, peak‐, and over‐aged 6063 alloy: A comparative study

The mechanical property of age‐hardenable Al‐alloys is governed by the state of ageing, which determines the microstructure and consequently, their corrosion behavior which is a vital aspect for a number of applications. This article presents a comparative assessment of corrosion behavior of under‐, peak‐ and over‐aged Al‐Mg‐Si alloy. Corrosion characteristics have been determined via immersion tests in 0.1 M ortho‐phosphoric acid solution and intergranular corrosion (IGC) tests. Corroded surfaces are examined by field emission scanning electron micrographs‐energy dispersive spectroscopy and 3D optical profilometer. The obtained results reveal that the corrosion rate at a specific immersion time as well as the depth of IGC increases in the order for under‐, peak‐, and over‐aged states. Irrespective of the state of ageing, corrosion loss increases linearly but the rate of corrosion decreases rapidly with increasing immersion time. The dominant mode of corrosion in under‐aged alloy is identified as localized pitting, while peak‐aged is highly susceptible to IGC in contrast extensive pitting corrosion is observed for over‐aged alloy. The observed differences in corrosion behavior are explained considering characteristics of precipitates. Formation of β (Mg₂Si) in case of over‐aged alloy and presence of inclusions like AlFeMnSi particles are found to accelerate pitting corrosion.     

Study on metamerism degree evaluation based on wavelength sensitive cone weighting algorithm

Metamerism phenomenon can be used in illuminant detection to ensure the accuracy of light source. A method based on Long‐, Middle‐, Short‐ wavelength cones(LMS) weighting algorithm to evaluate metamerism degree is proposed. The chromatic relationship between the degree of metamerism mismatch and the light source is studied. Herein, the consistency between the metameric indices (MIs) and CIE1976 L*a*b* color difference ranking is analyzed by SRCC, KRCC, PLCC and RMSE. A statistically sampling method to obtain practical LMS cone fundamentals to evaluate metamerism degree is employed. The analysis results obtained show that the method based on LMS weighting algorithm has good evaluation ability and stability in simulation experiments and statistically sampling experiments, which are in line with visual characteristics of human. Proposed method meets the requirements of selecting metameric pairs used in light source detection. The analysis results have certain guiding significance.     

锅炉对流管爆裂原因分析

采用化学分析、金相检验及力学性能测定等方法，对锅炉对流管爆裂原因进行了分析。结果表明，长期超温运行而引起的蠕变是导致爆裂的主要原因。     

IPv6过渡机制讨论

本文在简要地介绍Ngtrans工作组提出的大多数过渡机制的基础上，尝试对它们进行区分、分类，并对每一种过渡机制的优缺点进行分析。另外．还对这些机制的布置以及一部分支持这些机制的产品平台进行讨论。     

多测井曲线的综合处理合成

测井曲线是地质分层的基础，但在利用单一测井曲线解决复杂地质问题时也存在多解性和局限性。为克服多解性，人们采用多种测井曲线进行地质分层，提高了分层的精度。本文在此基础上提出把多条曲线分别赋予不同的加权因子，然后进行归一化处理，形成一条标准综合参数测井曲线。此综合参数曲线突出了所选的多条测井曲线的公共信息，减少或削弱了单一测井曲线中的偶然误差，提高了综合后测井资料的可信度。该方法可应用于地质分层、岩性分析、含油气预测等诸多领域。应用时要注意，并非所选择的测井曲线种类越多越好，而是要选择那些最能反映地层单元特征信息的测井曲线。     

基于神经网络基础上的两种系统安全综合评价方法

从工业企业生产发展的特点出发,在界定安全评价概念的基础上，从系统论的角度简要介绍了运用三层BP神经网络技术进行安全综合评价的方法和安全模糊综合评价方法。通过对这两种较为流行的安全评价方法进行分析，指出了传统评价方法的不合理性，辨证说明了这两种评价方法的优越性。     

VRDS装置常压分馏塔系统的问题分析

胜利炼油厂重油加氢 (VRDS)装置的常压分馏塔为填料塔 ,2 0 0 1年检修开工后该系统出现异常 ,经过查找分析 ,确定轻烃 /产品减压渣油换热器和柴油汽提塔重沸器内漏是装置异常的主要原因     

加油站油品用体积交接存在的问题及建议

叙述了目前加油站在实行按任意温度下的体积交接，由于未考虑油品体积随温度、压力、密度的变化，出现了零售损耗很大的问题。建议加油站在现阶段采用“准标准体积”交接；在由体积转换为质量计算加油站损溢时，使用油库当月发出的平均密度；当财会核销损溢时，不使用盘存的体积和固定密度进行计算的方法，而使用实际盘点的质量数，以真实反映加油站的当期损溢。     

油气集输管道最佳敷设方式的分析

根据大庆油田油气集输工艺设计的实践，分析了几种实用的油气集输管道敷设方式的优缺点。在对不同敷设方式的管道热耗做了较详细计算的基础上，进行了比较，提出了确定油气集输管道的最佳敷设方式：站外管道基本上采用埋地敷设；站内管道则应依据站址处的常年最高地下水位资料来确定，即在保证管道不长期受地下水浸泡的前提下，站内室外管道以埋地敷设为主，室内管道以架空与理地同时敷设为最佳；地下水位高的站内，以架空敷设最佳。