无油润滑压缩机活塞环和支承环设计

通过对填充聚四氟乙烯材料活塞环及带卸荷槽结构支承环的研究 ,确定了活塞及活塞环结构 ,建立了带卸荷槽支承环的力学分析模型 ,并将其结果用于结构尺寸的确定。在压缩机工艺指标不变的情况下 ,用该方法设计的活塞环和支承环性能优良。     

薄板坯连铸工艺液芯压下的有限元分析

简要介绍世界几种主要薄板坯连铸工艺。着重叙述应用大型通用商业软件MSC.MARC。模拟液芯压下时铸坯的变形，确定最佳压下方案的有限元分析，液芯压下应该在结晶器出口处及二冷区扇形段开始部分进行，这样能减小铸坯的应变。     

无掩模激光干涉光刻技术研究

介绍了一种不用掩模的光刻技术———激光干涉光刻技术的基本原理,给出了干涉光刻技术的主要特点及一些可能的应用,并对实验系统和初步实验结果进行了分析。研究表明,激光干涉光刻具有大视场和分辨率高和视场宽等优点。     

挤压力对晶体生长速度及枝晶间距的影响

研究了挤压铸造时挤压力对宏观晶体生长速度的影响，给出了晶体生长速度表达式。结果表明：挤压力对合金宏观晶体生长速度的影响除与合金成分有关外，在某些挤压条件下，当形核率的增加幅度超过长大速度时，则挤压力可使宏观晶粒细化；反之，会使宏观晶粒变粗。随着挤压力的提高，合金凝固速度加快，一次枝晶间距和二次枝晶间距都随之减小，从而细化了树枝晶。     

Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.     

连铸喷嘴特性测试与分析

通过测试连铸二冷喷嘴性能，对比同型号喷嘴使用前后两种状态下特性参数，分析了喷嘴参数变化的原因。提出了对使用中的喷嘴特性进行检测与校核的建议，以确保喷嘴特性满足铸坯二冷工艺条件，保证铸坯质量。     

提高超小型铝电解电容器生产一次合格率

恰当选择原材料、确保铆接工序质量、重视工作电解液的配比、严控各工序成品率是提高超小型铝电解电容器投入产出一次合格率的关键。以１０Ｖ－４７μＦ（４ｍｍ×７ｍｍ）产品为例，投入产出一次合格率达９４％以上。     

无粘结预应力蛋形消化池的施工技术

石家庄市桥东污水处理厂有6座11500m3无粘结预应力混凝土蛋形消化池,本文介绍其非预应力钢筋、模板体系、混凝土和预应力工程等结构施工成套技术。     

Failure of a Cast Aluminum Engine Head in a High Performance Application

The investigation described in this article examined a cast aluminum head used in a high performance (drag racing) application. These engine heads had been failing within a few seconds of startup. A sample head was examined to determine the cause. Visual inspection found two cracks on the exhaust side of the head. One crack initiated at the bottom of a spark plug well. The head was then sectioned for metallographic examination and fracture analysis. Metallographic examination revealed a large number of shrinkage pores throughout the casting. The fracture surface intersected many of these shrinkage pores. A significantly sized pore was located near the bottom of the suspect spark plug well near a stress-concentrating feature. This pore acted as the crack-initiating defect, which caused the engine head to fail.     

开放的ladder型无反转激光系统的稳定性分析

利用开放的ladder型无反转激光系统的密度矩阵运动方程组的定态解和激光场运动方程分析了系统的稳定性。结果表明：如果增益大于激光腔损耗，则零解是不稳定的；如果增益小于激光腔损耗，则零解是稳定的；如果增益大于激光腔损耗，则非零解是稳定的。