引进意大利连续纺丝机车间空调节能设计

介绍了某化纤厂引进意大利十二台粘胶连续纺丝机车间与以往的纺丝车间相比,空调设计中的节能途径,体现了既满足工艺要求,又降低生产成本的设计目的。     

薄板坯连铸工艺液芯压下的有限元分析

简要介绍世界几种主要薄板坯连铸工艺。着重叙述应用大型通用商业软件MSC.MARC。模拟液芯压下时铸坯的变形，确定最佳压下方案的有限元分析，液芯压下应该在结晶器出口处及二冷区扇形段开始部分进行，这样能减小铸坯的应变。     

挤压力对晶体生长速度及枝晶间距的影响

研究了挤压铸造时挤压力对宏观晶体生长速度的影响，给出了晶体生长速度表达式。结果表明：挤压力对合金宏观晶体生长速度的影响除与合金成分有关外，在某些挤压条件下，当形核率的增加幅度超过长大速度时，则挤压力可使宏观晶粒细化；反之，会使宏观晶粒变粗。随着挤压力的提高，合金凝固速度加快，一次枝晶间距和二次枝晶间距都随之减小，从而细化了树枝晶。     

马家河水电站的设计

马家河水电站通过在马家河和毛家河上游分别建底栏栅坝和低拱坝 ,经各自的引水系统将水引至两河口汇合流入前池发电。本文介绍了电站的开发方案 ,厂区、引水工程和取水枢纽的布置和设计     

连铸喷嘴特性测试与分析

通过测试连铸二冷喷嘴性能，对比同型号喷嘴使用前后两种状态下特性参数，分析了喷嘴参数变化的原因。提出了对使用中的喷嘴特性进行检测与校核的建议，以确保喷嘴特性满足铸坯二冷工艺条件，保证铸坯质量。     

Sandia National Laboratories Validation Workshop: Structural dynamics application

This article specifies a virtual structural dynamic subsystem and some systems, as well as mathematical models that approximately simulate them. The purpose is to define a setting for model validations conceived by participants in the Sandia National Laboratories Validation Workshop. Some broad guidelines for the model validations are set, as well as a regulatory requirement to be satisfied by the target system. Participants are directed to present techniques for subsystem model validation, to analytically predict whether or not the regulatory requirement will be met, and to estimate the likelihood of accuracy of the prediction.     

工业厂房48M抽柱工程施工工艺

以莱钢万力H型钢有限公司抽柱换梁工程为例，介绍行车梁拼装、柱加固拆除及托粱吊装前后的测量观测。     

Failure of a Cast Aluminum Engine Head in a High Performance Application

The investigation described in this article examined a cast aluminum head used in a high performance (drag racing) application. These engine heads had been failing within a few seconds of startup. A sample head was examined to determine the cause. Visual inspection found two cracks on the exhaust side of the head. One crack initiated at the bottom of a spark plug well. The head was then sectioned for metallographic examination and fracture analysis. Metallographic examination revealed a large number of shrinkage pores throughout the casting. The fracture surface intersected many of these shrinkage pores. A significantly sized pore was located near the bottom of the suspect spark plug well near a stress-concentrating feature. This pore acted as the crack-initiating defect, which caused the engine head to fail.     

单层工业厂房可靠性的模糊综合评判

主要研究了单层工业厂房可靠性模糊综合评判法的基本理论与实施方法．通过一工程实例，表明用这种定量方法来处理厂房可靠性评判中的大量不确定信息是科学、合理而又实用的．     

低压铸造流动与传热耦合计算的研究

根据低压铸造充型流动的特点 ,利用计算机数值模拟技术 ,对低压铸造充型阶段的流动怀传热过程进行了耦合计算 ,从而保证了模拟结果的准确性和可靠性。在此基础上开发出了模拟软件 ,并对实际低压铸件进行了模拟分析 ,结果与实际生产情况吻合很好