基于DSP的智能电源控制单元设计与实现

本文利用TI公司TMS320F28335芯片高效的浮点运算能力,结合片上丰富的外设,设计并实现了一种具有高可靠性的智能电源控制单元。该控制单元周期性地对各片上外设进行自检维护,完成多路负载通道控制、电压、电流的实时监控,并对故障进行指示、处理和上报,同时提供人机交互界面更新状态信息。经过验证,该控制单元工作稳定,具备良好的工程应用价值。     

面向工程应用的单片机课程教学改革与实践

在分析传统单片机教学存在问题的基础上,提出面向工程应用,聚焦企业需要,构建能力递进、面向应用的内容体系,搭建资源共享、实践创新、师生互动的自主学习平台,组建培养兴趣,突出技能的“双师型”教学团队,实践表明,在传授知识的同时,能有效提升学习兴趣,优化人才素质结构。     

Influences of chip serration on micro-topography of machined surface in high-speed cutting

Saw-tooth chip changes from macroscopically continuous ribbon to separated segments with the increase of cutting speed. The aim of this study is to find the correlations between chip morphology and machined surface micro-topography at different chip serration stages encountered in high speed cutting. High strength alloy steel AerMet100 was employed in orthogonal cutting experiments to obtain chips at different serration stages and corresponding machined surfaces. The chips and machined surfaces obtained were then examined with optical microscope (OM), scanning electron microscope (SEM), and white light interferometer (WLI). The result shows that chip serration causes micro-waves on machined surface, which increases machined surface roughness. However, wave amplitudes (surface roughness) at different serration stages are different. The principal factor influencing wave amplitude is the thickness of the sawed segment (tooth) of saw-tooth chip. With cutting parameters in this study, surface roughness contributed by chip serration ranges from 0.39 μm to 1.85 μm. This may bring on serious problems in the case of trying to replace grinding with high-speed cutting in rough machining. Some suggestions have been proposed to control the chip serration-caused surface roughness in high-speed cutting based on the results of the current study.     

Artificial bee colony based algorithm for maximum power point tracking (MPPT) for PV systems operating under partial shaded conditions

Artificial bee colony (ABC) algorithm has several characteristics that make it more attractive than other bio-inspired methods. Particularly, it is simple, it uses fewer control parameters and its convergence is independent of the initial conditions. In this paper, a novel artificial bee colony based maximum power point tracking algorithm (MPPT) is proposed. The developed algorithm, does not allow only overcoming the common drawback of the conventional MPPT methods, but it gives a simple and a robust MPPT scheme. A co-simulation methodology, combining Matlab/Simulink™ and Cadence/Pspice™, is used to verify the effectiveness of the proposed method and compare its performance, under dynamic weather conditions, with that of the Particle Swarm Optimization (PSO) based MPPT algorithm. Moreover, a laboratory setup has been realized and used to experimentally validate the proposed ABC-based MPPT algorithm. Simulation and experimental results have shown the satisfactory performance of the proposed approach.     

基于DSP的多元数据同步采集与存储系统的设计与实现

从硬件和软件两个角度出发,介绍基于DSP的多元数据同步采集与存储系统的组成、工作模式以及功能的测试。系统主要由上位机和数字采集与存储单元组成,其中数字采集与存储单元的硬件部分包括电源模块,值班电路模块,数据采集模块,数据存储模块,时钟同步模块。系统采用DSP作为中央处理芯片,利用经过同步后的秒脉冲作为触发信号,实现同步数据采集。以CF卡作为存储介质,实现数据自容式存储。软件部分实现自检、同步、数据采集存储功能。经过测试,系统工作稳定,功能正常,同步精度在100ns以内。     

实时操作系统DSP/BIOS在DSP开发中的应用

本文介绍了RTOS(实时操作系统)DSP／BIOS在DSP的开发设计中的应用。在简述了DSP的一般模型后，论述了RTOS在DSP／BIOS外设管理，实时性能分析以及程序流程控制中的应用。     

图形点阵式液晶显示器MSP-G320240在高速处理器DSP中的应用

介绍了内置SD1335控制器的图形液晶显示器MSP-G320240的工作原理及应用方法，给出了MSP-G320240液晶显示器同DSP的简单接口电路，同时给出了相应的液晶显示器的初始化和清显示区的具体程序。     

2.5GHz低相位噪声CMOS LC VCO的设计

用0 .35μm、一层多晶、四层金属、3.3V的标准全数字CMOS工艺设计了一个全集成的2 .5 GHz L C VCO,电路采用全差分互补负跨导结构以降低电路功耗和减少器件1/ f噪声的影响.为了减少高频噪声的影响,采用了在片L C滤波技术.可变电容采用增强型MOS可变电容,取得了2 3%的频率调节范围.采用单个16边形的对称片上螺旋电感,并在电感下加接地屏蔽层,从而减少芯片面积,优化Q值.取得了在离中心频率1MHz处- 118d Bc/ Hz的相位噪声性能.电源电压为3.3V时的功耗为4 m A.     

串行16位DAC转换芯片在流量手操器中的应用

本文介绍串行16位D／A转换芯片MAX541及其与AT89C52单片机的接口电路、相应的转换子程序，并给出其在过程流量手操器中的应用。     

DSP--数字化时代的基因芯片

DSP是当今发展最为迅速的和最有发展前景的技术之一。与普通CPU和MCU相比 ,DSP在数字信号处理方面有着无可比拟的优势 ,特别适合网络、通信、控制等需要进行大量数字信号处理的应用场合。今天DSP已经成为通信、计算机、网络、工业控制以及家用电器等电子产品中不可或缺的基础器件 ,DSP在通信、计算机、网络、工业控制以及消费类电子产品等领域有着非常广泛的应用 ,本文阐述了DSP的特点、应用和市场以及DSP技术的发展前景。