Validation of performance of real-time kinematic PPP. A possible tool for deformation monitoring

Structural failures (bridge or building collapses) and geohazards (landslides, ground subsidence or earthquakes) are worldwide problems that often lead to significant economic and loss of life. Monitoring the deformation of both natural phenomena and man-made structures is a major key to assessing structural dynamic responses. Actually, this monitoring process is under real-time demand for developing warning and alert systems.One of the most used techniques for real-time deformation monitoring is the Global Navigation Satellite System (GNSS) real-time procedure, where the relative positioning approach, using a well-known reference station, has been applied.This study was conducted to evaluate the actual quality of the real-time kinematic Precise Point Positioning (PPP) GNSS solution for deformation monitoring, where it can be concluded that a promise tool is under development and should be taken into account on actual and near future real-time deformation monitoring studies and applications.     

中厚板轧制边部不均匀变形机理的探讨

通过分析宽中厚板轧制过程中的边部不均匀变形，探讨了其影响因素及大宽度板“切边纵裂”的产生原因，提出了解决问题的具体办法。     

Gleeble 3800热模拟试验机在宝钢的典型应用与功能开发

热模拟试验可研究成分与各工艺参数对组织和性能的影响，用于指导产品设计和实际生产工艺的制定，还有助于建立数学模型。文章介绍了Gleeble 3800热／力模拟试验机在宝钢实际应用中的几个典型试验，包括高温热塑性试验、多道次变形试验、冷轧薄板相转变点试验和HAZ焊接热影响区热模拟试验等。这些试验可用来解决连铸、轧钢和冷轧产品热处理生产中存在的一些问题。     

THE FRACTURE MECHANISM OF 475°C EMBRITTLEMENT IN A DUPLEX STAINLESS STEEL

The mechanism of “475°C embrittlement” of a duplex stainless steel was investigated using finite element modelling of the stress distribution at brittle fracture initiation. Brittle fracture initiated at a critical shear stress, which increased with ferrite hardness. The fracture stress was affected by the duplex microstructure. Fracture was nucleated by deformation twins, which were identified using electron back-scatter diffraction. The ductile-to-brittle fracture transition was sensitive to age-hardening and could be described simply by the effect of age-hardening and test temperature on the yield stress.     

Growth and characterization of hot-wall epitaxial CdTe on (111) HgCdTe and CdZnTe substrates

Thin CdTe films were deposited by hot-wall epitaxy (HWE) on (111) HgCdTe and CdZnTe substrates at temperatures from about 140 to 335°C. X-ray rocking curves were used to show that crystal quality of the CdTe (111)B films improved as substrate temperature increased from 140 to about 250°C. Rocking curve values for full width at half maximum (FWHM) decreased from 2–4 degrees at 140–150°C to less than 100 arc-s at 250°C, and a FWHM of 59 arc-s was the lowest value observed near 250°C. The FWHM of the HWE CdTe was found to be insensitive to growth rate below about 400Å/min, but increased to four degrees at 1250Å/min. X-ray diffraction confirmed that films grown on the B-face at higher temperatures were epitaxial, but contained a significant volume fraction, 35% to 50%, of rotational in-plane twins. Electron microscopy confirmed a coarse twin density, and photoluminescence spectra showed an absence of excitonic emission in the HWE films. Simultaneous growth on two (111) HgCdTe substrates with different surface polarities between 230°C and 335°C showed that deposition rate on the A-face decreased relative to that on the B-face as temperature increased. Films grown on the B-face exhibited better surface morphologies than those grown on the A-face.     

Slip and Twinning in Polycrystalline Alumina (α-Al2O3) Deformed under Hydrostatic Pressure between 600° and 1000°C

The microstructure of polycrystalline alumina deformed under hydrostatic pressure and at low temperature is investigated by transmission electron microscopy. Deformation occurs mainly by prism plane slip and rhombohedral twinning. Introduction of hydrogen leads to a significant decrease in the yield stress. In large grain size alumina deformed with hydrogen, accommodation of twinning involves dislocation reactions in the twin boundary and in the grains rather than by cracking. Prism plane dislocations decompose into basal dislocations by cross slip probably due to a decrease of Peierls stress for basal slip in the presence of hydrogen.     

Equivalent Strains in Severe Plastic Deformation

The concept of equivalent plastic strain is discussed. Definitions may be based on kinematic arguments (like change of geometry) or on equivalence of plastic work. Complications arise when strain is accumulated in increments with variable strain path.     

圆锥形零件冲压变形与成形载荷的分析

由于悬空侧壁部分的变形状态是圆锥形零件成形的关键，而径向拉应力是实现悬空部分成形的必要条件，同时也是该部分冲压成形成败的关键为此，经力学分析得出了侧壁部分径向拉应力的解析式和造成圆锥形零件破裂的最大径向拉应力的计算式。同时分析了圆锥形零件的成形载荷。     

Sicherer und wirtschaftlicher Betrieb von Kraftwerken – Ergebnis der Forschung im Bereich Werkstoffe,Auslegung und Instandhaltung

Safe and Economic Operation of Power Plants – Research Results in the Field of Materials, Design and Maintenance Components of power plants which undergo high temperatures are subjected to complex loading situations. The requirements on the used materials result from the special operation conditions of the plants and have to be adjusted to the steadily growing requirements on higher efficiency of the complete power plant as well as to those of safe and economic operation. The expenses for control and downtimes are directly connected with economic efficiency and availability. However, in case of new procedures or components it is not possible to revert to the existing know‐how. Different failure mechanisms than known before can occur. The same goes for the load situation. Therefore the knowledge base has to be extended to in‐advance or even parallely running scientific examinations that life assessment and maintenance strategies can be applied which guarantee the operational reliability and the efficiency of the plant. The main emphasis of these F&E works has to be put on condition monitoring based on actual operational data, the standard materials’ and component’s behaviour (deformation, damage and failure behaviour) in connection with design of components and the related material laws. In the framework of applied AVIF projects, following problems are handled:. – qualification of materials by determinating parameters related to practise. – optimal design of components by making available material laws and numerical tools. – economic manufacturing of components by qualifying processing methods such as welding. – The results can be transferred to concepts for safe and economic operation of power plants, especially for newly introduced materials for which there is no operational experience available.