高温旋风除尘器的设计

在PTA(精对苯二甲酸)的生产过程中,工艺废气经尾气膨胀透平机降压后进入RTO蓄热式焚烧炉将有毒有害的有机物焚烧分解后排入大气,为了达到粉尘的排放标准(小于120mg/m~3),在焚烧炉之后加上这台高温烟气除尘器,废气经除尘后达到了排放标准,而且最大程度地减少了热量损失,实践证明此项改造是成功的。文章探讨如何进行高温烟气除尘器的设计,并介绍了高温多管陶瓷旋风烟气除尘器的结构。     

A scheme to randomly generate surface dust points for the 3D complex variable boundary element method (CVBEM)

A scheme to randomly generate dust points on the surface of a three-dimensional (3D) object is proposed. This scheme will potentially eliminate the bias of a density of points which are approximately equally spaced on the surface, as well as eliminate possible weighting requirements for areas of higher density. This method has the potential to reduce computational effort, as fewer points might be required to define the surface area. The global trial function vector can be assigned to these dust points and then entered into the complex variable boundary element method (CVBEM) commercial code. This scheme can be applied to each piece of a system that is comprised of a connected multiple geometry. A noticeable benefit of this approach is that the same problem can be studied several times, using a new random distribution of surface points each time. The smallest error can then be determined and that run selected. The Mathematica code used to generate the scheme is attached as an appendix.     

Motion compensated film restoration

Motion picture films are susceptible to local degradations such as dust spots. Other deteriorations are global such as intensity and spatial jitter. It is obvious that motion needs to be compensated for before the detection/correction of such local and dynamic defects. Therefore, we propose a hierarchical motion estimation method ideally suited for high resolution film sequences. This recursive block-based motion estimator relies on an adaptive search strategy and Radon projections to improve processing speed. The localization of dust particles then becomes straightforward. Thus, it is achieved by simple inter-frame differences between the current image and motion compensated successive and preceding frames. However, the detection of spatial and intensity jitter requires a specific process taking advantage of the high temporal correlation in the image sequence. In this paper, we present our motion compensation-based algorithms for removing dust spots, spatial and intensity jitter in degraded motion pictures. Experimental results are presented showing the usefulness of our motion estimator for film restoration at reasonable computational costs. Received: 9 July 2000 / Accepted: 13 January 2002 Correspondence to:S. Boukir     

降低闪速炉烟灰发生率的探讨

本文详细地阐述了闪速炉冶炼过程烟灰发生的原因以及不利影响 ,并积极地寻求降低烟灰发生率的有效措施 ,具有实际操作意义。     

测尘仪原理与应用

本文介绍了测尘仪器的基本原理,着重阐述了透射法和散射法的基本原理和实际应用.     

Handling of fine-particles by time-averaged particle driving method in plasmas

We developed a noble technique for the fine-particle handling in plasmas. In this method a pair of point electrodes are introduced in the plasma, to which positive pulses are applied alternatively. When the pulse repetition period is shorter than the particle response time, the particles feel only time-averaged force because of their large mass. Spatial profile of the equivalent potential of the time-averaged force varies from a circle to an ellipse with an increase in the local discharge at the electrodes. The particles are eventually transported toward a middle point between two point-electrodes, being almost independent of their initial positions. This method is quite effective for converging fine particles in the plasma.     

水泥生产除尘效果模糊综合评价研究

文中阐述了基于层次分析的水泥生产除尘效果模糊综合评价方法。利用层次分析将复杂的决策系统分解成若干个简单的决策系统，将模糊数学应用于判别水泥生产除尘效果的优劣，使得难以量化的质量评价问题转化成定量的结果。     

大浓度范围内PV型旋风分离器粒级效率的计算方法

探讨了旋风分离器入口含尘浓度对其分离性能及粒级效率的影响机理。对旋风分离器内部气固两相运动进行了相似分析,得到了包括入口含尘浓度在内的一系列影响分离性能的相似准数。通过相似试验及试验数据的多元回归分析,建立了各相似准数与粒级效率的关系,得出了能精确估计大浓度范围内PV型旋风分离器粒级效率的计算公式。     

A comparative study of dust control practices in Chinese and Australian longwall coal mines

Mine dust is one of the main hazards in underground longwall mines worldwide.In order to solve the mine dust problem,a significant number of studies have been carried out regarding longwall mine dust control,both in China and Australia.This paper presents a comparative study of dust control practices in Chinese and Australian longwall mines,with particular references to statutory limits,dust monitoring methods and dust management practices,followed by a brief discussion on the research status of longwall mine dust control in both countries.The study shows that water infusion,face ventilation controls,water sprays,and deep and wet cutting in longwall shearer operations are commonly practiced in almost all underground longwall mines and that both Chinese and Australian longwall mine dust control practices have their own advantages and disadvantages.It is concluded that there is a need for further development and innovative design of more effective dust mitigation products or systems despite the development of various dust control technologies.Based on the examinations and discussions,the authors have made some recommendations for further research and development in dust control in longwall mines.It is hoped that this comparative study will provide beneficial guidance for scholars and engineers who are engaging in longwall mine dust control research and practice.     

A new design of foaming agent mixing device for a pneumatic foaming system used for mine dust suppression

To overcome the drawbacks of the conventional foam technology used for dust suppression,including large pressure loss,high water pressure and low driving pressure,a new pneumatic foaming system is introduced.Then an original design of foaming agent mixing device is proposed,and its performance is investigated and evaluated under different pressure compensations.Experimental results show that the maximum absorption amount increases by 2.9-6.7 times at a pressure compensation of 0.04-0.2 MPa compared with no pressure compensation.The pressure loss and pressure fluctuation both reduce significantly with increasing pressure compensation.The critical outlet pressure increases by30.4-240%.Field application indicates that the proposed mixing device ensures the reliable addition of foaming agent used for foam dust suppression.The effect of foam on dust suppression is remarkable,and the economic cost of foam is low.Therefore,there is reason to believe that the new mixing device will greatly promote foam technology to be widely used for suppressing dust in underground coal mines.