Growth,mechanical properties,and tribological performance of TiAlN/NbN and NbN/TiAlN bilayer coatings

Three different coatings, namely TiAlN, TiAlN (external)/NbN (internal) and NbN (external)/TiAlN (internal), were deposited on cemented carbides by arc ion plating. The comparative investigation conducted in this study elucidates the effect of the NbN layer and coating systems on the growth, mechanical properties, and tribological performance of the coatings. The results showed that the surface of the TiAlN and TiAlN/NbN coatings was smoother when TiAlN served as the external layer. The NbN/TiAlN coating, wherein NbN formed the external layer, had a much rougher but more symmetrical surface. With the introduction of the NbN layer, the increased micro stress induced a lower adhesion strength in the TiAlN/NbN and NbN/TiAlN coatings. The TiAlN/NbN and NbN/TiAlN coatings exhibited higher hardness and hardness/effective elastic modulus (H/E*). During the friction test, when the temperature was elevated to 700 °C, the tribological performance of the monolayer TiAlN coating was the lowest because of the TiO₂-induced breakage of the dense tribo-oxide film. The NbN layer participated in the formation of a NbO_x film at elevated temperatures, which was responsible for the high tribological performance of the two bilayer coatings. When the NbN layer was on the outermost layer and in direct contact with the elevated temperature atmosphere, the NbN/TiAlN coating generated a tribo-oxide film with high integrity, and its coefficient of friction decreased by 27% of that at room temperature. Therefore, the NbN/TiAlN coating exhibited the highest wear resistance at 700 °C.     

Crystallization of progesterone polymorphs using polymer-induced heteronucleation (PIHn) method

Progesterone is a natural hormone steroid used in humans for several treatments and in livestock for artificial insemination, which exhibits two polymorphic forms at ambient conditions: form 1 and form 2. Form 2 is metastable and more soluble than form 1; however, it is not suitable to use as powder raw material because it transforms into form 1 by the effects of grinding. A polymorphic screening of progesterone based on polymer-induced heteronucleation method was performed as an alternative to prepare the metastable form. Polyvinyl alcohol, hydroxypropyl methylcellulose (HPMC), dextran, gelatin, polyisoprene (PI) and acrylonitrile-butadiene (NBR) copolymer were used. Crystals were prepared from 0.5, 10 and 40?mg/mL solutions in acetone at room temperature by solvent evaporation. The samples were characterized by X-ray powder diffraction, differential scanning calorimetry (DSC), scanning electron microcopy and attenuated total reflectance infrared Fourier transform spectroscopy. Form 1 was nucleated from 40?mg/mL solutions on the six polymers and from 10?mg/mL solutions on PI and NBR. The mixture of form 1 and form 2 was obtained from 10?mg/mL solution on HPMC, dextran and gelatin and from 0.5?mg/mL solution crystallizations. Therefore, the polymeric devices, which crystallized the metastable and more soluble polymorph (2) of progesterone, would be a promissory alternative for the pharmaceutical applications.     

腐殖酸对烤烟根系生长和生理活性的影响

对腐殖酸和基肥混施进行了烤烟盆栽试验。结果表明 ,腐殖酸能有效刺激根系的生理活性 ,提高根系抗坏血酸氧化酶、多酚氧化酶等呼吸酶的活性 ,增强根系的活力 ,并能有效促进烤烟根系生长 ,根干重、体积和长度均有提高。     

Nondestructive evaluation of the characteristics of degraded materials using backward radiated ultrasound

The frequency dependency of Rayleigh surface wave is investigated indirectly by measuring the angular dependency of the backward radiation of the incident ultrasonic wave in two kinds of degraded specimens by scuffing or corrosion. Then, the frequency dependency is compared with the residual stress distribution or the corrosion-fatigue characteristics for the scuffed or corroded specimens, respectively. The width of the backward radiation profile increases with the increase of the variation in residual stress distribution for the scuffed specimens. In the corroded specimens, the profile width decreases with the increase of the effective aging layer thickness and is inversely proportional to the exponent, m, in the Paris’ law that can predict the crack size increase due to fatigue. The result observed in this study demonstrates high potential of backward radiated ultrasound as a tool for nondestructive evaluation of subsurface gradient of material degradation generated by scuffing or corrosion.     

挤压力对晶体生长速度及枝晶间距的影响

研究了挤压铸造时挤压力对宏观晶体生长速度的影响，给出了晶体生长速度表达式。结果表明：挤压力对合金宏观晶体生长速度的影响除与合金成分有关外，在某些挤压条件下，当形核率的增加幅度超过长大速度时，则挤压力可使宏观晶粒细化；反之，会使宏观晶粒变粗。随着挤压力的提高，合金凝固速度加快，一次枝晶间距和二次枝晶间距都随之减小，从而细化了树枝晶。     

Determination of shear strength values according to EN 408

This paper presents the results of 382 shear tests carried out according to EN 408. The test pieces consisted of spruce (Picea abies) and varied in density and ring width orientation (radial, tangential and at an angle of 45° to the steel plates). In addition pieces containing pith and knots were tested. The paper discusses problems observed when using this test configuration and shows that the test results do not support the characteristic shear strength values as given in EN 338. Moreover, the test results do not support the relationship between characteristic shear strength and characteristic bending strength as given in EN 384.

---

Résumé Cet article présente les résultats de 382 essais de cisaillement menés conformément à EN 408. Les éprouvettes d’essai sont en épicéa (Picea abies) et présentent une variabilité en termes de masse volumique et d’orientation des cernes d’accroissement (radiale, tangentielle, à un angle de 45° par rapport aux plaques métalliques). Des éprouvettes supplémentaires contenant du cœur et des nœuds ont également été testées. L’article évoque les problèmes qui ont été mis en évidence lors de l’utilisation de ce dispositif expérimental et montre que les résultats expérimentaux ne sont pas en accord avec les valeurs caractéristiques de résistance au cisaillement données dans EN 338. De plus, ces résultats ne confirment pas la relation entre résistance caractéristique au cisaillement et résistance caractéristique à la flexion telle que stipulée dans EN 384.

     

半导体衬底片的应力损伤及其行为

本文根据实际测量结果,一叙述了半导体衬底制片质量对外延生长的影响。特别是,讨论了在 GaAs、InP 衬底中,产生于切片、研磨和抛光加工过程中的机械损伤的影响。     

Growth of Fe on Si (100) at room temperature and formation of iron silicide

Low-energy electron diffraction (LEED), Auger electron spectroscopy and X-ray photoelectron spectroscopy (XPS) investigations of both the growth of an iron film on silicon (100) at room temperature and the subsequent formation of iron silicide are the subjects of this paper. An in-situ cleaned silicon (100) wafer without carbon or oxygen contamination exhibiting the known 2 × 1 reconstruction in the LEED pattern served as the substrate. Iron was deposited on this reconstructed surface at 300 K. The comparison of theoretical calculations based on three growth mechanisms with XPS data obtained with take-off angles of 0° and 50° clearly demonstrates a layer-by-layer growth of the iron film on silicon (100). At 300 K no formation of iron silicide was observed, although an interaction between iron and silicon could be detected at the interface. The formation of iron silicide was observed at annealing temperatures of 630–730 K. Quantitative XPS analysis yields the presence of FeSi₂, when the thickness is large enough. Neither the iron film on silicon nor the silicide shows any LEED pattern.     

激光辐照对不同饵料微藻生长的影响

利用Nd:YAG激光(波长1.06μm,功率5W,照射时间0.5-3min)和Ar 激光(波长:488nm,功率70mw,照射时间5-20min)分别照射角毛藻和叉鞭金藻,辐照后进行细胞增殖和生长速率的测定。实验结果表明:照射剂量为1min的Nd:YAG激光及剂量为5min的Ar 激光对叉鞭金藻有较明显的促长效果,这两种激光处理组的细胞增殖量在辐照后的两天内较对照组分别高42.9%和48.1%,但这种促长效果随时间的推移逐渐消失。不同剂量的两种激光辐照角毛藻后,在延滞期均出现生长抑制现象,但进入指数生长期或传代培养后,剂量为1min的Nd:YAG激光及剂量为10min的Ar 激光对角毛藻有明显的促长效果,其中在指数生长期1min剂量的Nd:YAG激光处理可促长27.0%,传代培养后10min的Ar 激光处理组生长速率提高达51.2%。本文对不同激光及不同激光参数条件下,两种饵料藻的耐受性及生长特性的差异也进行分析探讨。本实验结果不仅证实了已有研究的推论,还展示出激光技术在饵料藻种选育中的应用前景。