On the thermally-induced seizure in bearings: A review

This paper presents a state-of-the-art survey of papers reported on the nature of a troublesome failure mode in bearings known as seizure. This mode of failure is thermally-induced and it occurs in both journal and rolling element bearings. To gain insight, particular attention is given to reported experimental observation, various mechanisms involved, and available prediction methodologies.     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

High-load, squeeze action linear bearings with beam deflection

The literature provides little information on high-speed, high-normal-load, plain linear bearings, although the case for two rigid surfaces in relative linear motion can readily be solved by assuming squeeze action resistance. A new genus of internal combustion engines based on the Stiller-Smith mechanism incorporates connecting rods constrained by linear bearings, with the central normal load on the rod restricted by an oil film. A general analysis takes into account the bending of the rod, when the distributed oil film pressure resists the distributed load on the elastic rod. Design charts result that yield the dimensionless velocity at which the rod sinks in the oil as a function of the dimensionless load and the bearing clearance, and predict the deflection of the beam. The rod clearance history simulations for the Stiller-Smith engine compare favourably with computations for the rigid beam, confirming the analysis technique.     

Solution of temperature fields in hydrodynamics bearings by the numerical network method

Solution to the 2-D steady-state nonlinear heat conduction equation, involving cylindrical coordinates, applied to a plain bearing by a simple and versatile numerical technique based on network method is presented in this work. These advantages of the technique are necessary for the status evaluation of industrial machines during operation because time and computing resources are limited. The pressure field in the fluid is previously solved from the Reynolds equation by finite element method. The main difficulty is associated with the exponential dependency of the viscosity on temperature. The proposed model is very efficient and requires negligible computing times. Solutions are very close to the experimental and numerical results of other researchers.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

住宅建筑结构中隔震技术的应用和经济评价

对当前隔震系统做了简单介绍 ,介绍了基础隔震的技术和施工方法等。讨论在住宅结构中推广隔震技术的方法 ,对各种类型的住宅结构做经济评价 ,讨论推广的可能性和难点。     

液力偶合器在电动煤气鼓风机系统的应用

煤气鼓风机为适应系统煤气量的变化采用改变风机的转速来进行调节是一有效的节能方法。本文介绍了液力偶合器的结构特点、工作原理及其在煤气鼓风机系统中的应用，以实现风机的调速，并取得了明显的节能效果。     

Dissolution of phase-separated domains after a jump to a temperature in the single-phase region

Phase-separated domains prepared in the two-phase region were dissolved at a temperature in the single-phase region, and their dissolution dynamics was studied by using the time-resolved light scattering (TRLS) technique and a scanning electron microscope (SEM). The time t_ps of preparation of domains was chosen to be long enough for phase separation to proceed into the late stage. The scattered light intensity at small wavenumbers increased before it attenuated. As t_ps increased, the increase at smaller wavenumbers became more significant and the peak intensity decreased only slightly with dissolution time. The characteristic wavenumber q_m evaluated from TRLS and SEM followed the power-law relation q_mt^−0.3.     

Complementary modelling of fluid separation processes

Optimal functioning of numerous technological processes depends primarily on relevant process design, properly selected column internals and sufficient understanding of the process behaviour. This can be achieved only with the help of accurate and reliable process models capable of considering process rates in a rigorous way, with respect to both transport phenomena and chemistry. In this article, a new modelling concept called complementary modelling is suggested for a large class of fluid separation processes. Since the conditions and criteria for these processes vary considerably, it is impossible to develop a unified modelling approach. Instead, a reasonable and effective combination of different modelling approaches provides solutions to many present and future tasks. The complementary modelling is discussed in detail and illustrated with several case studies.     

Hydrodynamic force between two hard spheres tangentially translating in a power-law fluid

The hydrodynamic interaction between two hard spheres tangentially translating in a power-law fluid is investigated. By considering the gap between the two spheres being sufficiently small such that the Reynolds’ lubrication theory applies, an analytical equation to the pressure in the gap is obtained using truncated Fourier series. To a good approximation, the pressure equation can be further simplified. The simplified approximate equation over-predicts the pressure for shear thickening fluid (n>1) but under-predicts the pressure for shear-thinning fluid (n<1). However, the errors in the predicted tangential force and moment are relatively small. In particular, for a Newtonian fluid, the accurate solution and the simplified approximate solution degenerate to the asymptotic solution of Goldman et al. [1967. Slow viscous motion of a sphere parallel to a plane wall-motion through a quiescent fluid. Chemical Engineering Science 22, 637-651.] and O’Neill and Stewartson [1967. On the slow motion of a sphere parallel to a nearby plane wall. Journal of Fluid Mechanics 27, 705-724.]. Both solutions predict that for shear thickening fluid (n>1), the hydrodynamic force converged in the inner region of the gap between the two spheres and the contribution from the outer region is sufficiently small. For shear thinning fluid (n<1), the contribution from the outer region is also significant.