Al、Mo含量对铸造钛合金力学性能的影响

运用正交实验 ,考察了Al、Mo含量对Ti Al Mo 1Zr系铸造钛合金力学性能的影响。试验结果表明 :随Al、Mo含量提高 ,铸造合金的强度增加 ,塑性和冲击韧性降低 ,但Al、Mo的交互作用却使合金塑性提高 ,强度和冲击韧性降低     

Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.     

Formation and growth mechanism of TiC crystal in TiC_p/Ti composites

1　ＩＮＴＲＯＤＵＣＴＩＯＮＰａｒｔｉｃｌｅｓｒｅｉｎｆｏｒｃｅｄｔｉｔａｎｉｕｍａｌｌｏｙｍａｔｒｉｘｃｏｍｐｏｓｉｔｅｓ(ＴＭＣｐ)ｈａｖｅｗｉｄｅａｐｐｌｉｃａｔｉｏｎｆｉｅｌｄｓｆｏｒｔｈｅｉｒａｔｔｒａｃｔｉｖｅｈｉｇｈｓｐｅｃｉｆｉｃｓｔｒｅｎｇ     

Chemical leaching and magnetic properties of non-equilibrium Al(Co–Cu) powders produced by rod milling

We report upon the chemical leaching and magnetic properties of nanoscale crystalline Al_0.6(Co₂₅Cu₇₅)_0.4 alloy powders produced by rod milling. X-Ray diffractometry (XRD), transmission electron microscopy, differential scanning calorimetry, vibrating sample magnetometry, and superconducting quantum interference device magnetometry were used to characterize the as-milled and leached specimens. After 400 h of milling, only the b.c.c. phase of the intermetallic compound γ-Al_3.892Cu_6.10808 was detected by XRD. After annealing the leached specimen at 600 °C for 1 h, the nanoscale crystalline phase was transformed into the f.c.c. Cu phase, and this was accompanied by a change in the magnetic properties. The peaks of the magnetization shifted towards lower temperature with increasing external field. The temperature behavior at T_f (45 K) for direct current (d.c.) magnetic susceptibility measurements was quite different for field cooling and zero-field cooling. After cooling the leached specimen from 800 °C, magnetization increased gradually.     

The corrosion behavior of sputter-deposited aluminum-tungsten alloys

Thin films on aluminum-tungsten alloys were prepared by co-deposition of pure aluminum and pure tungsten, each sputtered by an independently controlled magnetron source, on glass and sapphire substrates. Completely amorphous films were obtained in the Al₈₀W₂₀-Al₆₇W₃₃ composition range. Passivity and corrosion behavior of amorphous Al-W alloys were investigated in 1 M deaerated hydrochloric acid solution using polarization and impedance spectroscopy measurements and have been correlated with the properties of pure alloy components. Tungsten and sputter-deposited Al-W thin films are inherently passive materials while aluminum undergoes pitting corrosion in hydrochloric acid solution. The passive film formed at the OCP on each alloy possesses excellent electric and dielectric properties comparable to those of the isolating film on tungsten. The absolute impedance increases with increasing tungsten content in the alloy. According to electrochemical polarization measurements, alloying Al with W in solid solution significantly enhances the material's resistance to pitting corrosion by shifting the breakdown potential above 2000 mV (Al₆₇W₃₃) and lowering the corrosion rate at the OCP by more than two orders of magnitude. The most likely mechanism explaining the passivity of amorphous Al-W alloys, the Solute Vacancy Interaction Model (SVIM), involves the formation of complexes between highly oxidized solute atoms (W⁺⁶) and mobile cation vacancies, which restrict the transport of Cl⁻ through the oxide film and inhibit its breakdown in hydrochloric acid solution. The role that film stress relaxation effects and microscopic defects in amorphous Al-W films, of the some composition, and deposited on various substrates play in their corrosion resistance is discussed.     

MB8镁合金薄板的搅拌摩擦焊

针对我国航空航天工业常用的MB8镁合金。采用搅拌摩擦焊工艺进行焊接，对其焊缝的成形特点、组织特征和力学性能进行分析。结果表明，采用搅拌摩擦焊焊接镁合金效果良好。     

钨合金废料的资源再生利用技术

钨是一种稀有金属，钨合金具有高的强度、硬度，较好的耐高温性、耐密性和良好的电性能。广泛应用于航空航天工业、兵器工业、核工业、信息产业、汽车工业和钢铁工业等行业。目前，钨资源短缺，钨合金价格高、用量大，因此各国都把废弃的钨合金作为宝贵的第二钨资源加以再生利用。本文综述了钨合金的再生利用现状，分别总结了硬质合金、高比重合金、钨铜合金和钨材的再生利用技术，并利用生态环境材料的观点。对每种再生利用技术作了简单的评价。     

Corrosion Inhibition Mechanism with Spilt Cell Technique of Rare Earth Metal on LC4 Al Alloy

A new method of studying the corrosion inhibition mechanism of rare earth metal(REM) on LC4 Al alloy with the spilt cell technique was studied. The principle and experimental method of the spilt cell technique were analyzed. By measuring the change of net-electric current between the two electrodes caused by the change of the amount of oxygen in the solution and the addition of CeCl₃, the influence of corrosive performance of CeCl₃ on LC4 super-power aluminum alloy in the 0.1 mol·L⁻¹ NaCl solution was investigated. Meanwhile, the conditional changes of pH values, CeCl₃ solution, additire and time of performance were also studied. Finally, the features of electrode surface were revealed by using SEM and X-ray energy-dispersive spectrometry (EDS). By combining these with other electric chemical techniques, such as potential-time curve, polarization curve et al.     

SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.      

镍氢电池负极用低成本储氢合金的研究

研究了ABS型储氢合金在低Co含量条件下，随B组元替代元素Co，Al，Si等含量的变化对合金电化学性能的影响规律，同时研究了A组元中不同La／Ce比对合金电化学性能的影响情况。结果表明，随合金中Co含量的降低，合金的活化性能和放电容量得以改善，但合金的循环寿命下降也比较明显；在试验范围内，随Al元素的加入，合金的循环寿命得以改善，但材料的放电容量和活化性能均有所下降；随合金La／Ce比的降低，合金的放电容量略有下降，但其循环寿命和放电电压平台有较大提高。