Magnetic field-enhanced photocatalytic nitrogen fixation over defect-rich ferroelectric Bi2WO6

Photocatalytic N₂ fixation is a promising and sustainable manufacturing process of ammonia (NH₃); however, the NH₃ production rate by this method is very low, thus severely restricting further application of this sustainable technology. Therefore, developing an efficient photocatalyst for N₂ fixation under mild conditions is urgently required. Herein, ferroelectric Bi₂WO₆ materials with different surface oxygen defects were prepared, and the concentration of corresponding defects was controlled by adjusting the thermal reduction time. The abundant oxygen defects in Bi₂WO₆ can provide more reactive sites to promote the effective adsorption of N₂, and the photogenerated charge carrier can be efficiently separated benefiting from the internal electric field. These would weaken the N₂ triple bond and reduce the activation energy barrier for the conversion of N₂ to NH₃ under mild conditions. In the absence of sacrificial agents and cocatalysts, the optimized Bi₂WO₆ with oxygen defects shows an indigenous NH₃ yield of 132.175 μmol·g^-1·L^-1·h^-1, which is more than two times higher than that of the original Bi₂WO₆. Surprisingly, the Bi₂WO₆ with oxygen defects produced more than eight times NH₃ (471.13 μmol·g^-1·L^-1·h^-1) than that of the original Bi₂WO₆ when assisted by an external magnetic field, thus providing a new perspective for further enhancing the N₂ fixation performance.     

Topology optimization of flexure hinges with a prescribed compliance matrix based on the adaptive spring model and stress constraint

This paper focuses on the configuration design of flexure hinges with a prescribed compliance matrix and preset rotational center position. A new method for the topology optimization of flexure hinges is proposed based on the adaptive spring model and stress constraint. The hinge optimization model is formulated by maximizing the bending displacement with a spring while optimizing the compliance matrix to a prescribed value. To avoid numerical instability, an artificial spring is used as an auxiliary calculation, and a new strategy is developed for adaptively adjusting the spring stiffness according to the prescribed compliance matrix. The maximum stress of flexure hinge is limited by using a normalized P-norm of the effective von Mises stress, and a position constraint of rotational center is proposed to predetermine the position of the rotational center. In addition, to reduce the error of the stress measurement, a simple but effective filtering method is presented to obtain a complete black-and-white design. Numerical examples are used to verify the proposed method. Topology results show that the obtained flexure hinges have the prescribed compliance matrix and preset rotational center position while also meeting the stress requirements.     

Psychrophilic hydrogen production from petrochemical wastewater via anaerobic sequencing batch reactor: techno-economic assessment and kinetic modelling

Independent hydrogen production from petrochemical wastewater containing mono-ethylene glycol (MEG) via anaerobic sequencing batch reactor (ASBR) was extensively assessed under psychrophilic conditions (15–25 °C). A lab-scale ASBR was operated at pH of 5.50, and different organic loading rates (OLR) of 1.00, 1.67, 2.67, and 4.00 gCOD/L/d. The hydrogen yield (HY) progressed from 134.32 ± 10.79 to 189.09 ± 22.35 mL/gMEG_initial at increasing OLR from 1.00 to 4.00 gCOD/L/d. The maximum hydrogen content of 47.44 ± 3.60% was achieved at OLR of 4.0 gCOD/L/d, while methane content remained low (17.76 ± 1.27% at OLR of 1.0 gCOD/L/d). Kinetic studies using four different mathematical models were conducted to describe the ASBR performance. Furthermore, two batch-mode experiments were performed to optimize the nitrogen supplementation as a nutrient (C/N ratio), and assess the impact of salinity (as gNaCl/L) on hydrogen production. HY substantially dropped from 62.77 ± 4.09 to 6.02 ± 0.39 mL/gMEG_initial when C/N ratio was increased from 28.5 to 114.0. Besides, the results revealed that salinity up to 10.0 gNaCl/L has a relatively low inhibitory impact on hydrogen production. Eventually, the cost/benefit analysis showed that environmental and energy recovery revenues from ASBR were optimized at OLR of 4.0 gCOD/L/d (payback period of 7.13 yrs).     

Stress-deformable state of isotropic double curved shell with internal cracks and a circular hole

This work is devoted to the stress–strain state of isotropic double curved shell with defect system. The construction is weakened by two non-through thickness (internal) cracks of different length and by a circular hole located between cracks. In this study we use the line-spring model. Within the framework of this model cracks are modeled as mathematical cuts of shell’s middle surface. This leads to a two-dimensional problem. The problem is reduced to a system of eight boundary integral equations. To ensure the uniqueness of solution an additional equation is added. In the numerical solution of the problem special quadrature formulas for singular integrals of Cauchy type and the finite difference method are applied. The influence of defects on each other for double curved shell has been investigated. The given theoretical results can be used for the calculation of structural elements with holes, cracks on the strength and fracture toughness in various branches of engineering.     

Analysis of nitrogen oxide emissions from modern vehicles using hydrogen or other natural and synthetic fuels in combustion chamber

The paper presents a calculated analysis of the equilibrium emission of nitrogen oxides on the exhaust of carburetor and diesel internal combustion engines. The temperature of fuel oxidation is assumed to be 1,400 °C while the pressure for carburetor and diesel engines is assumed to be 60 atm and 80 atm respectively. The studies have been carried out for natural and synthetic fuels such as hydrogen, ethanol, methanol, petroleum, diesel fuel and methane at the excess air coefficient corresponding to the fuel oxidation temperature of 1,400 °C. In the paper, the method for calculating the equilibrium composition based on the equilibrium constant and mass conservation equations has been applied. It is shown that with an increase in pressure from 1 atm to 60 atm for carburetor engines and up to 80 atm for diesel engines, the reaction of nitrogen dioxide formation may shift towards an increase in NO₂. The formation of NO may be not affected by the increase in pressure by virtue of the fact that the reaction proceeds without changes in the amount. It has been determined that NO is the major atmospheric pollutant. However, it would be advisable to use more extensively the fuels characterized by the lowest output of nitrogen dioxide (methane and methanol), since nitrogen dioxide (NO₂) related to the 2nd hazard class is appeared to be the most dangerous to humans. It has been revealed that the reduction in oxidation temperature using hydrogen as a fuel for electrochemical current generators may allow reducing nitrogen oxide emissions by more than an order of magnitude as compared to the best results for ICE.     

空间红外大口径折射式低温镜头设计与验证

针对目标探测类空间红外相机大范围成像、高灵敏度探测、高精度定位等应用需求,文中提出采用像方远心光路和低温光学技术结合的解决方案,设计了物方视场角8°×8°、入瞳口径265 mm、工作温度200 K的像方远心折射式光学系统。镜头最大口径280 mm,采用多级分散的弹性支撑设计,解决大口径低温透镜装框、透镜组件支撑和镜头整体安装各环节的热应力卸载问题。在保证高刚度和低漏热的情况下,使低温下透镜的热应力对镜头能量集中度的影响降低到可接受范围内。镜头完成装调及室温下像质确认后,进行了力学振动试验,并将其制冷到200 K水平测试像质,测试结果表明,镜头能量集中度达到轴上75%,边缘视场72%。     

恢复邢台百泉泉水流量可行性研究

通过百泉泉区天然状态与超采状态下的水环境对比分析,并对岩溶水补给量和开采量进行计算,阐述恢复邢台百泉泉水流量的可行性,随着“引朱济邢”和“南水北调”供水工程的实施,邢台百泉水生态环境的恢复将变为现实。     

气调库及气调库设备

分析果蔬贮藏保鲜期的生理变化，介绍气调保鲜库设计施工验收中的技术要求，保鲜工艺和主要设备。     

炉衬产生的氧对真空钢液脱氮的动力学影响

采用 99.99%氧化镁砂捣打炉衬的 2 0kg真空感应炉 ,研究了超低碳钢熔炼时炉衬产生的氧对真空钢液脱氮的影响。试验结果表明 :钢液中氧含量在 1 2 0× 1 0 - 6 时 ,脱氮的限制性环节是界面化学反应 ;随炉衬中氧的逸出 ,当钢液中氧含量在 5 1 0×1 0 - 6 时 ,真空钢液脱氮处于界面化学反应和液相边界层扩散控制的边缘区域 ,脱氮速率降低     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.