Effect of heat treatment on tensile properties of friction stir welded joints of 2219-T6 aluminium alloy

Abstract

The effect of post-weld heat treatment (PWHT) on the tensile properties of friction stir welded (FSW) joints of 2219-T6 aluminium alloy was investigated. The PWHT was carried out at aging temperature of 165°C for 18 h. The mechanical properties of the joints were evaluated using tensile tests. The experimental results indicate that the PWHT significantly influences the tensile properties of the FSW joints. After the heat treatment, the tensile strength of the joints increases and the elongation at fracture of the joints decreases. The maximum tensile strength of the joints is equivalent to 89% of that of the base material. The fracture location characteristics of the heat treated joints are similar to those of the as welded joints. The defect free joints fracture in the heat affected zone on the retreating side and the joints with a void defect fracture in the weld zone on the advancing side. All of the experimental results can be explained by the hardness profiles and welding defects in the joints.     

DEVELOPMENT OF CALCULATING MODEL APPLICABLE FOR CYLINDER WALL DYNAMIC HEAT TRANSFER

In the calculation of submarine air conditioning load of the early stage, the obtained heat is regarded as cooling load. The confusion of the two words causing the cooling load figured out is abnormally high, and the change of air conditioning cooling load can not be indicated. In accordance with submarine structure and heat transfer characteristics of its inner components, Laplace transformation to heat conduction differential equation of cylinder wall is carried out. The dynamic calculation of submarine conditioning load based on this model is also conducted, and the results of calculation are compared with those of static cooling load calculation. It is concluded that the dynamic cooling load calculation methods can illustrate the change of submarine air conditioning cooling load more accurate than the static one.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Characterisation of FR-4 substrate with various plasma treatment conditions

Abstract

The effects of plasma treatment on the surface of the flame resistant-4 (FR-4) substrate with underfills under various treatment conditions (operating gas, operating time, operating power) are investigated by using contact angle measurement, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The plasma treatment on substrate surfaces increased the oxygen containing functional groups or the polar component of the surface free energy, improving the wetting characteristics of the underfills/FR-4 substrates. The plasma treatment conditions which minimised the contact angle between the underfills and FR-4 substrates were an operating power of 300 W and operating time of 180 s under Ar gas atmosphere.     

Impact of slag–refractory lining reactions on the formation of inclusions in steel

Abstract

The present study was carried out to investigate the impact of slag– refractory lining reactions on the formation of inclusions during ladle treatment of steel. The experiments were conducted on an industrial scale in the ladle at Uddeholm Tooling AB in Hagfors, Sweden. The inclusion chemistry and population during ladle treatment were studied along with the composition of the ladle glaze, taken from the ladle lining. The inclusions in the steel were classified into four groups according to the Swedish standard SS 111116. SEM/EDS analyses were carried out to identify the phases present in both the inclusions and the ladle glaze. The number of inclusions in the steel before deoxidation was found to increase with the ladle age, i.e. the number of times the ladle had been in use. A similar increase was also found after vacuum degassing and before casting. A great portion of inclusions before casting was found to be supplied by ladle glaze. This observation was further confirmed and explained by thermodynamic analysis. The present results show that ladle glaze is a major source of inclusions in the ladle at Uddeholm Tooling.     

Effects of heat treatment processes on microstructure and properties of 2·25Cr–1Mo–0·25V HSLA steels

Abstract

In the present paper, the effects of the heat treatment processes with two conditioning treatments and four quenching–tempering processes on the mechanical properties of 2·25Cr–1Mo–0·25V high strength low alloyed (HSLA) steel are investigated. The results show that the conditioning treatments have obvious effects on the low temperature impact energy but little effect on the tensile strength. The elevation of the final austenitising temperature increases the strength, whereas it results in the decrease in the low temperature impact energy due to the coarse microstructure. The results of the fracture surfaces analysis further make sure that the fracture surfaces of tensile specimens all exhibit ductile characters with a lot of dimples. However, the fracture surfaces of impact specimens exhibit two typical fracture characters, i.e. the ductile and brittle fracture surface corresponding to the fine and coarse microstructures respectively. In addition, the elongation and reduction in area seem to be insensitive to the heat treatments. Meanwhile, the impact fracture mode is more sensitive to the grain size and not to the low temperature impact energy.     

Coupled heat and fluid flow model and experimental verification of aluminium plate die casting

Abstract

The present work aims to forecast mould filling, void shape, location and size as well as columnar to equiaxed transition (CET) in commercial pure aluminium casting. A model coupling the momentum equations of the fluid flow and heat transfer equations is presented, in which metallostatic pressure, air gap and oxide layer are considered. Different casting parameters were investigated such as casting configuration by varying the plate thickness from 5 to 20 mm, melt superheat from 40 to 120°C, mould preheat up to 200°C and different pouring heads ranging from 0·3 to 0·6 m. Regarding the microstructure and void formation, the approach based on the Niyama criterion, was considered. The experimental verification of the model was achieved by gravity die casting in the form of a rectangular cavity. Voids inside aluminium plate were investigated by X-ray imaging. Microstructure and CET was investigated microscopically. The supposed model proves its validity for mould filling and in detecting the void features and CET.     

Development of precipitate size and volume fraction of niobium carbonitrides in stabilised stainless steel

Abstract

Niobium carbonitride (NbX) precipitates have been studied in a niobium stabilised austenitic stainless steel AISI type 347 with approximate nominal composition Fe–0.06C–17.5Cr–11.4Ni–0.8Nb. The steel was extruded to seamless tube, solution annealed at 1100°C for 3 min, water quenched, and subsequently isothermally aged at 700°C for times up to 70 000 h. Size distribution and volume fraction of the coarse distribution (1–10 µm) of NbX particles were measured using scanning electron microscopy (SEM). The fine distribution (～30 nm) was investigated using energy filtered transmission electron microscopy (EFTEM). Size distribution and volume fraction were determined using jump ratio images. Coarse NbX (～0.3% volume fraction) precipitates were formed during solidification and extrusion, and were little affected by solution annealing and isothermal aging. Fine NbX (～0.5% volume fraction) precipitates formed during solution annealing and grew during the first 800 h of aging. Precipitate size determination using EFTEM appears to give accurate results, while volume fraction determination requires homogeneous material for good results.     

A magnetic resonance compatible surgical manipulator: part of a unified support system for the diagnosis and treatment of heart disease

A prototype of a magnetic resonance (MR)-compatible surgical manipulator was designed and evaluated. The manipulator is designed so as to fit into vertical magnetic field open-configuration MR imagers. Moreover, it is designed to work without being fixed to an MR imager, and its electrical circuits and lines of actuators and sensors are independent of the room shield so that it could be installed in various kinds of settings at many MR imager sites without any additional construction. The MR compatibility of the manipulator was evaluated: no noticeable deformation was observed in the MR images even when the manipulator was in motion. Although the signal-to-noise deterioration ratio was higher than that previously reported, the MR images were thought to be good enough for recognizing the whole structure of a targeted organ and for following the relative position of the manipulator tip with regard to the target, i.e. MR tracking.     

Particle break-up during heat treatment of 3000 series aluminium alloys

Abstract

In wrought aluminium alloys, the fragmentation of coarse, iron bearing intermetallic particles by hot rolling is an important development in industrial processing. Here a model 3000 series alloy is used to show that fragmentation can occur prior to hot rolling, during the homogenisation heat treatment. Some fragmented particles display a curved morphology of break-up that results from matrix wetting of two phase (or 'duplex') interfaces in Al₆(Fe,Mn) particles partially transformed to an α-Al–(Fe,Mn)–Si phase. In contrast, samples rapidly heated to temperature in a fluidised bath show an angular break-up indicative of tensile stresses induced by thermal expansion mismatch between the intermetallic particles and aluminium matrix. Although this break-up should not be industrially significant, the transformation induced break-up by wetting may be. More generally, internal boundaries resulting from the transformation to α-Al–(Fe,Mn)–Si phase may be mechanically weak fracture initiation points during hot rolling.