Influence of pulse-jet cleaning pressure on performance of compact dust collector with pleated filter operated in clean-on-time mode

To operate a bag filter continuously, pulse-jet cleaning of dust particles from the filter medium is commonly required, and the pulse-jet pressure significantly affects the filter performance. In this study, the accumulation structure of residual dust particles inside and on the surface of a filter medium at different pulse-jet pressures was investigated by constructing a simple model, and the influence of the dust structure on the filter performance was clarified. Using a simple model, we determined the effective ratio of filtration area β, which represents the ratio of the filterable area to the total filtration area, the true resistance coefficient due to the primary dust layer ζ_p’ thinly deposited on the filter surface, and the true resistance coefficient inside the filter media itself ζ_f’_. The effective ratio of filtration area β decreased with operation time for all pulse-jet pressures; however, it maintained a high value when the pulse-jet pressure was high. The validity of β analyzed by the model was verified using two different methods, and the results showed good agreement, indicating that the model is effective in identifying real conditions. The true resistance coefficient due to the primary dust layer ζ_p’ decreased as the pulse-jet pressure increased; however, the true resistance coefficient inside the filter media itself ζ_f’ was the highest at 0.5 MPa. In addition, the dust collection efficiency was different at each pulse-jet pressure, which was considered to be caused by the difference in the dust particle accumulation structure.     

Pressure control of an electro-hydraulic actuated clutch via novel hysteresis model

This paper mainly focuses on the development of pressure tracking control logic of electro-hydraulic actuators for vehicle application. This is done to improve and ensure the performance of a precise lower-level controller for evolving modern shift control logic. The required performance is obtained by hysteresis model-based feed-forward control and additional feedback control. The hysteresis and the time delay, which adversely affect pressure control, are well known nonlinear behaviors in electro-hydraulic actuators. In order to cope with the hysteresis, a novel hysteresis model is proposed based on a physical phenomenon. A mathematical model based on a characteristic curve obtained in preliminary experiments is presented using only one tuning parameter, and this model can be inverted easily to construct a feed-forward controller. In addition, a feedback controller is designed considering the stability margin of a time delay system. The feedback control inputs ensure compensation of the feed-forward errors caused by model error and uncertainty. The proposed controller is designed to lower computational cost considering applicability for production vehicles. As a result, the developed pressure controller is applied to a transmission control unit of a production vehicle and verified experimentally for various driving scenarios.     

Temperature- and frequency-dependent hysteresis scaling behaviour and phase transitions in a [001]c 0.73Pb(Mg1/3Nb2/3)O3-0.27PbTiO3 single crystal

The dielectric properties and bipolar polarization-electric field (P-E) and strain-electric field (S-E) dynamic hysteresis of a relaxor [001]_c 0.73Pb(Mg_1/3Nb_2/3)O₃-0.27PbTiO₃ (PMN-0.27PT) single crystal were investigated to reveal more details of the temperature-induced phase transitions. Different linear scaling relations for ferroelectric hysteresis area <A>, coercive field E_c, saturation polarization P_s and remnant polarization P_r versus temperature τ were measured in different temperature regions. For each measurement frequency f, all hysteresis parameters were found to decrease linearly with temperature in the temperature range of the single rhombohedral (R) phase or tetragonal (T) phase, and the rate of decrease in the T phase was observed to be much larger than the corresponding rate in the R phase. In the temperature range near the R-T phase transition, the exponent α in the power law <A>∝f ^α for the R phase was found to be smaller than that for the T phase, and the magnitude of α depended strongly on temperature when the crystal was in the R-T coexisting phase state. Our experimental and theoretical results indicate that the difference in the activation energy and dipole moment in the R and T phases may lead to the observed discrepancy for the P-E and S-E hysteresis behaviour in different temperature regions.     

压电驱动器迟滞特性的Preisach模型研究

压电驱动器的迟滞特性是影响其位移输出精度的主要因素。该文采用改进的Preisach模型对压电驱动器的迟滞特性进行建模，并进行了相应的实验研究。实验结果表明该模型可以很好地预测压电驱动器在经过一定的控制电压序列以后的位移输出值．能够有效地降低迟滞特性对压电驱动器位移输出精度的影响。     

包装件压力试验机计算机测控系统

针对YE-50包装件压力试验机落后的测控系统，提出一种基于压力和位移闭环控制的计算机测控系统。根据测得的压力、位移和设定值，通过模糊控制输出驱动伺服阀实现了压力试验时的恒速控制和堆码试验时的恒力控制。并实时显示力——位移及应力——应变曲线。文中还对模糊控制器的实验整定方法进行了探讨。     

氢压缩机管道强烈振动的消除

本文针对一往复式氢气压缩机管道振动十分强烈的情况，分析了管系的结构自振频率、气柱固有频率和气流脉动，采取了改变管系结构频率和气柱固有频率的减振措施，经实践证明获得了较为理想的减振效果。     

一种多晶硅高温压力传感器

制作压力传感器时，在二氧化硅层上淀积多晶硅膜，既可利用优良的机械特性，又可保证压敏电阻与衬底间具有良好的绝缘性，由此可大大提高器件的温度特性。介绍了一种多晶硅压力传感器的原理和设计。实验结果表明，这类传感器具有灵敏度好，精度高等特点，电路工作范围为０－２５０℃，且具有良好的温度稳定性。     

控制棒驱动机构常温通风均匀性试验研究（续篇）

本文叙述控制棒驱动机构在常温通风均匀性方面的试验。通过平顶型堆顶结构和球面型堆顶结构通风均匀性试验的比较,找出通风的阻力、风速和不均匀系数间的规律。     

PTA装置压力离心机冲洗新技术

分析了仪征化纤PTA装置压力离心机运转效果不佳的原因,提出解决方案,改造实施后取得了很好的效果。