一种基于FPGA的可变速率帧结构设计与实现

在简述V.35接口的基础上针对V.35接口速率可变的应用需求提出了一种速率可变的帧结构,该帧结构可支持N×64kb/s(3≤N≤32)速率,从而在V.35接口上实现了多种速率的低速业务传输.     

High-voltage and low specific on-resistance power UMOSFET using P and N type columns

For the first time, we present the unique features exhibited by power 4H–SiC UMOSFET in which N and P type columns (NPC) in the drift region are incorporated to improve the breakdown voltage, the specific on-resistance, and the total lateral cell pitch. The P-type column creates a potential barrier in the drift region of the proposed structure for increasing the breakdown voltage and the N-type column reduces the specific on-resistance. Also, the JFET effects reduce and so the total lateral cell pitch will decrease. In the NPC-UMOSFET, the electric field crowding reduces due to the created potential barrier by the NPC regions and causes more uniform electric field distribution in the structure. Using two dimensional simulations, the breakdown voltage and the specific on-resistance of the proposed structure are investigated for the columns parameters in comparison with a conventional UMOSFET (C-UMOSFET) and an accumulation layer UMOSFET (AL-UMOSFET) structures. For the NPC-UMOSFET with 10 µm drift region length the maximum breakdown voltage of 1274 V is obtained, while at the same drift region length, the maximum breakdown voltages of the C-UMOSFET and the AL-UMOSFET structures are 534 and 703 V, respectively. Moreover, the proposed structure exhibits a superior specific on-resistance (R_on,sp) of 2 mΩ cm², which shows that the on-resistance of the optimized NPC-UMOSFET are decreased by 56% and 58% in comparison with the C-UMOSFET and the AL-UMOSFET, respectively.     

Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

IL-27与LTB4在非小细胞肺癌中的表达及意义

目的:探讨IL-27与LTB4在非小细胞肺癌组织中的表达情况及临床意义。方法:采用免疫组化S-P法分别检测60例非小细胞肺癌组织及正常肺组织中的IL-27与LTB4的表达水平。结果:IL-27与LTB4在肺癌组织中的总阳性表达率分别为41.67%、63.33%,各种检测指标的阳性率在肺癌组织与对照组之间均存在着差异性(P<0.05)。IL-27与LTB4的表达均与肿瘤的分化程度有关(P<0.05),IL-27的表达与肺癌的TNM分期相关(P<0.05),与病理类型无关(P>0.05)。LTB4的表达与组织学类型、临床分期无关(P>0.05),IL-27与LTB4之间存在密切相关性。结论:IL-27、LTB4与肺癌发生机制及发展有密切关系,联合进行检测两者表达水平对于肺癌临床诊断、评估恶性程度及判断预后有重要意义。     

软交换与3G网络互通关键技术分析

就软交换网络和WCDMAR4网络互通的关键技术进行了分析和探讨，并借此提出了对互通节点的技术要求。     

Thaumasite––direct, woodfordite and other possible formation routes

Two main formation routes for thaumasite exist below 15 °C. One is the direct route from C–S–H reacting with appropriate carbonate, sulfate, Ca²⁺ ions and excess water. The other route is the woodfordite route from ettringite reacting with C–S–H, carbonate, Ca²⁺ ions and excess water, in which thaumasite arises through the intermediate formation of the solid solution woodfordite. The woodfordite route for thaumasite formation appears to be relatively quicker (although still slow) than the direct route, presumably because with the former the ettringite already has the octahedral [M(OH)₆] units that can facilitate the critical change from [Al(OH)₆]³⁻ to [Si(OH)₆]²⁻ groupings. Both routes are mutually dependent on each other. The presence of magnesium salts can modify the path to thaumasite formation. High pressure might be able to stabilise [Si(OH)₆]²⁻ groupings and allow thaumasite to become formed above 15 °C. This possibility is discussed.     

Ring‐opening polymerization of lactones initiated by diphenylzinc–coinitiator systems

Diphenylzinc, alone or in combination with water and butanone as coinitiators, was used as a polymerization initiator system for a variety of lactones at varying temperatures. The resulting data indicate that the course of the polymerization is greatly influenced by the lactone structure, as well as by the molar ratio of coinitiator to diphenylzinc. When used alone, diphenylzinc exhibited high activity as an initiator in δ‐valerolactone polymerizations, although it was less efficient when used in the β‐butyrolactone and the β‐propiolactone polymerizations. Activity in the polymerization of β‐lactones was increased by adding small amounts of butanone or water. It was also observed that the diphenylzinc–butanone combination was more effective than the diphenylzinc–water mixture in the polymerizations of β‐butyrolactone and β‐propiolactone. Copyright © 2003 Society of Chemical Industry     

Biotransformation of l‐menthol by twelve isolates of soil‐borne plant pathogenic fungi (Rhizoctonia solani) and classification of fungi

The microbial transformation of l‐menthol ( 1 ) was investigated by using 12 isolates of soil‐borne plant pathogenic fungi, Rhizoctonia solani (AG‐1‐IA Rs24, Joichi‐2, RRG97‐1; AG‐1‐IB TR22, R147, 110.4; AG‐1‐IC F‐1, F‐4, P‐1; AG‐1‐ID RCP‐1, RCP‐3, and RCP‐7) as a biocatalyst. Rhizoctonia solani F‐1, F‐4 and P‐1 showed 89.7–99.9% yields of converted product from 1 , RCP‐1, RCP‐3, and RCP‐7 26.0–26.9% and the other isolates 0.1–12.0%. In the cases of F‐1, F‐4 and P‐1, substrate 1 was converted to (?)‐(1S,3R,4S,6S)‐6‐hydroxymenthol ( 2 ), (?)‐(1S,3R,4S)‐1‐hydroxymenthol ( 3 ) and (+)‐(1S,3R,4R,6S)‐6,8‐dihydroxymenthol ( 4 ), which was a new compound. Substrate 1 was converted to 2 and/or 3 by RRG97‐1, 110.4, RCP‐1, RCP‐3 and RCP‐7. The structures of the metabolic products were elucidated on the basis of their spectral data. In addition, metabolic pathways of the biotransformation of 1 by Rhizoctonia solani are discussed. Finally, from the main component analysis and the differences in the yields of converted product from 1 , the 12 isolates of Rhizoctonia solani were divided into three groups based on an analysis of the metabolites. Copyright © 2003 Society of Chemical Industry     

Evaluation of the Properties of Si3N4/Si3N4 Joint Brazed Using a Filler Alloy Containing Pd

Si3N4 ceramic was jointed to itself using a filler alloy of Cu76.5Pd8.5Ti15, and the mechanical properties of the jointwere measured and analyzed. By using a filler alloy of Cu76.5Pd8.5Ti15, the SisN4/SisN4 joints were obtained bybrazing at 1373～1473 K f     

草酸钙在硫酸软骨素自组装膜上周期沉淀的研究

利用硫酸软骨素(chondroitin sulfate，CS)在云母基底上通过浇铸法制备的自组装膜为基底，诱导草酸钙在其上的凝集生长。发现当硫酸软骨素的浓度为1．Omg／ml时在该膜体系中可形成规整的周期性草酸钙环状沉淀。这种有序的环状结构可能是耗散结构的一种具体表现形式。利用原子力显微镜(atomic forcemicroscope，AFM)和傅立叶红外光谱仪对这种结构进行了表征，实验结果显示合适浓度下形成的CS膜在一定程度上可以抑制草酸钙的凝集结晶，表明高分子基质与无机离子间强烈的相互作用对无机盐的成核结晶有显著影响，为探讨结石的形成与抑制提供了一定的实验依据。