Plasma-assisted CO2 reforming of methane over Ni-based catalysts: Promoting role of Ag and Sn secondary metals

Carbon dioxide (CO₂) and methane (CH₄) are the primary greenhouse gases (GHGs) that drive global climate change. CO₂ reforming of CH₄ or dry reforming of CH₄ (DRM) is used for the simultaneous conversion of CO₂ and CH₄ into syngas and higher hydrocarbons. In this study, DRM was investigated using Ag–Ni/Al₂O₃ packing and Sn–Ni/Al₂O₃ packing in a parallel plate dielectric barrier discharge (DBD) reactor. The performance of the DBD reactor was significantly enhanced when applying Ag–Ni/Al₂O₃ and Sn–Ni/Al₂O₃ due to the relatively high electrical conductivity of Ag and Sn as well as their anti-coke performances. Using Ag–Ni/Al₂O₃ consisting of 1.5 wt% Ag and 5 wt% Ni/Al₂O₃ as the catalyst in the DBD reactor, 19% CH₄ conversion, 21% CO₂ conversion, 60% H₂ selectivity, 81% CO selectivity, energy efficiency of 7.9% and 0.74% (by mole) coke formation were achieved. In addition, using Sn–Ni/Al₂O₃, consisting of 0.5 wt% Sn and 5 wt% Ni/Al₂O₃, 15% CH₄ conversion, 19% CO₂ conversion, 64% H₂ selectivity, 70% CO selectivity, energy efficiency of 6.0%, and 2.1% (by mole) coke formation were achieved. Sn enhanced the reactant conversions and energy efficiency, and resulted in a reduction in coke formation; these results are comparable to that achieved when using the noble metal Ag. The decrease in the formation of coke could be correlated to the increase in the CO selectivity of the catalyst. Good dispersion of the secondary metals on Ni was found to be an important factor for the observed increases in the catalyst surface area and catalytic activities. Furthermore, the stability of the catalytic reactions was investigated for 1800 min over the 0.5 wt% Ag-5 wt% Ni/Al₂O₃ and 0.5 wt% Sn-5 wt% Ni/Al₂O₃ catalysts. The results showed an increase in the reactant conversions with an increase in the reaction time.     

Magnetic properties and magnetoresistance effect of SnFe2O4 spinel nanoparticles: Experimental,ab initio and Monte Carlo simulation

In this contribution, SnFe₂O₄ nanoparticles were prepared by the solvothermal method, the structural properties were performed using X-Ray Diffraction (DRX) to prove the success of tin ferrite formation and to determine de crystals parameters. The size and morphological study were build using Scanning Electron Microscopy (SEM) and Transmission Electron microscopy (TEM), the results showed that the size of particles is uniform with a range of particles (5–7 nm). The magnetic properties were carried out using the SQUID device, the SnFe2O4 nanoparticles have a magnetic transition at 750 K. In addition, the hysteresis loops at low temperature displayed Ms and Mr equals to 23 emu/g and 6 emu/g, respectively. The magnetoresistance properties were investigated, the SnFe₂O₄ nanoparticles present a large magnetoresistance effect (80%). The experimental results are supplemented by model calculations utilizing density functional theory and Monte-Carlo simulations.     

Structural,magnetic, thermal and optical properties of Sn2+ cation doped magnetite nanoparticles

Tin doped nanomagnetites, Sn_xFe_3-xO₄, were synthesized with various concentrations of Sn²⁺ ion (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0) by co-precipitation method. XRD, VSM, TG-DTA, SEM-EDX and UV–Vis were used to characterize and study the structural, magnetic, thermal, and optical properties of Sn_xFe_3-xO₄ nanoparticles. XRD confirmed the presence of cubic structure and spinel phase of tin doped magnetites. The d-spacing, lattice parameter, density, crystallite size and cation distribution were derived from the XRD analysis. The M − H curves exhibited changes in saturation magnetization (M_s), coercive field (H_c), remanent magnetization (M_r) and susceptibility (χ), with increasing concentration of non-magnetic Sn²⁺ ions. Differential thermal analysis was used to study the thermal stability of Sn_xFe_3-xO₄ nanoparticles. The SEM images revealed the surface morphology of the nanoparticles and the EDX spectra showed an increase in the Sn content and a corresponding decrease in the Fe content for the tin doped samples. The optical bandgap was found to be centered at 3.9 eV for the synthesized materials. This systematic study may be the first comprehensive report on synthesis and characterization of tin doped magnetites.     

新型MSIS结构气敏电容的研究

采用静电喷雾高温分解工艺制备ＳｎＯ２气敏膜，并与Ｓｉ３Ｎ４－ＳｉＯ２集成多层介质膜，用催化金属Ｐｔ作栅电极，制成新型的ＭＳＩＳ结构气敏电容。通过检测平带电压的变化，研究对Ｈ２和Ｏ２的气敏特性，分析其气敏机理并提出了检测的物理模型．     

Modification of platinum surfaces by spontaneous deposition: Methanol oxidation electrocatalysis

The presence of a second metal on platinum surfaces affects the performance of methanol oxidation. However, most of the electrocatalytic reactions are studied by using electrochemically deposited platinum alloys, but in the case of spontaneous deposition the situation is not so clear since the surface distribution, stability and morphology are usually not well documented. The formation of surface decorated samples on mono- and poly-crystalline platinum is followed by electrochemical and spectroscopic techniques and analysis of their performance towards methanol adsorption and oxidation compared with that on pure platinum. Pt/Sn and Pt/Ru are of special interest because of their well-known performance in methanol fuel cells. Methanol oxidation on Pt(111)/Ru, Pt(111)/Sn and Pt(111) shows that ruthenium is the only one able to promote the reaction since the simultaneous dissolution of tin occurs and competes with the process of interest. The in situ infrared spectroscopy is used to compare methanol oxidation on Pt(111)/Ru and Pt(111) in acid media using p-polarized light. The formation of bridge bound carbon monoxide is inhibited in the presence of ruthenium ad-species, whereas on Pt(111) the three adsorption configurations are observed. Linear sweep polarization curves and Tafel slopes (calculated from steady state potentiostatic plots) for methanol oxidation are compared on polycrystalline surfaces modified by tin or ruthenium at different coverages. There is almost no change in the Tafel slopes due to the presence of the foreign metal except for Pt/Ru, where a 0.09 V decade⁻¹ slope was calculated below 0.55 V due to hydroxyl adsorbates on ruthenium islands. The anodic stripping of methanol residues on the three surfaces indicates a lower amount of carbon monoxide-type adsorbates on Pt/Ru, and the simultaneous tin dissolution process leading to residues oxidation on Pt/Sn electrodes.     

An effective rhodium catalyst system on the synthesis of acetic acid from methyl formate

Rh/Lil/SnR₄ is an effective catalyst system for the conversion of methyl formate to acetic acid under carbon monoxide pressure. The effects of solvent and initial CO partial pressure on the turnover rate of the reaction were investigated. The possibility of replacing some of the iodide promoters by tin compounds has been probed.     

Corrosion of tin in citric acid solution and the effect of some inorganic anions

The corrosion behaviour of tin in different concentrations of citric acid solutions (0.3–1.0 M, pH=1.8) was studied at 30 °C by potentiodynamic technique. The E/I profiles exhibit an active passive behaviour. The active dissolution involves one anodic peak A associated with a dissolution of the metals as Sn(II) species. The passivity is due to the formation of thin film of SnO₂ and or Sn(OH)₄ on the anode surface. The cathodic sweep shows a small peak C related to the reduction of the passive film. The peak current density I_p of peak A increases with increasing both acid concentration and sweep rate.

The effects of adding increasing concentrations of Na₂CrO₄, NaMoO₄, NaNO₃ and NaNO₂ on the corrosion of tin in 0.5 M citric acid at 30 °C were investigated. Both CrO₄²⁻ and MoO₄²⁻ ions inhibit the corrosion of tin and the extent of inhibition enhances with their concentrations. Addition of either NO₃⁻ or NO₂⁻ accelerates the corrosion of tin. NO₃⁻ ions are more aggressive than NO₂⁻ ions.     

Rich photoluminescence emission of SnO2–SiO2 composite aerogels prepared with a co-fed precursor sol–gel process

Tin oxide–silica composite aerogels were successfully prepared with a co-fed precursor sol–gel process. The crystallinity of the tin oxide nanoparticles, embedded in the mesoporous SiO₂ network, was improved with increasing the post-reaction thermal treatment temperature. The composite aerogels exhibited a rich photoluminescence (PL) emission contributed by both SnO₂ and SiO₂. The PL peak of 346 nm was from the near band edge emission of the tin oxide nanoparticles, and the ones located at 310 and 476 nm were attributable to the oxygen deficiencies of the silica network. Three more emission peaks, 387, 432, and 522 nm, were observed, with the 387 nm peak contributed by the oxygen vacancies V_O⁺⁺, the 432 nm peak by the Sn interstitials, and the 522 nm peak by the oxygen vacancies V_O⁺, respectively, of the tin oxide nanoparticles. The intensities of these three defect level emissions were found decreased, as compared to that of the near band edge emission, with increasing the post-reaction thermal treatment temperature as the tin oxide crystallinity improved.