Residual stresses and transformation toughening in MoSi2 composites reinforced with partially stabilized zirconia

The results of study of the effects of yttria stabilization (0–6 mol.%) on the room-temperature fracture behavior and toughening mechanisms in zirconia-reinforced MoSi₂ are presented in this paper. Transformation toughening is shown to occur only in composites reinforced with zirconia particles stabilized with 2 mol.% yttria. However, the fracture toughness levels are comparable in the other composites with yttria levels between 0 and 6 mol.%. Toughening in the other composites is attributed to the combined effects of residual stress, microcrack shielding/anti-shielding and/or crack deflection. A rigorous micromechanics-based model is presented for the estimation of residual stress levels in brittle materials reinforced with phases that can transform during cooling or under stress. The model is applied successfully to the rationalization of the observed fracture and toughening phenomena.     

Comparison of Displacement and Mixing Diffusers

In order to cumpare the peformance of different supply diffuers of ventilation air, the airflow passern, temperature stratifiation and contaminant dispersion in a furnitured office ventilated by three kinds of air diffuer were numerically investigated. The air diffuers studied in this paper are a quarter-cylinder displacement diffuer on the floor and mixing diffuers (linear and vortex diffuers) on the ceiling. The heat sources in the of-fice are considered to be 50% convective and 50% radiative. The k-? two-equatwn model of turbulence is employed to predict the turbulent diffusion. The results show that the displacement diffuser provides a rather uniform flow field with low velocify in most areas, and the vertical temperature difference from floor to ceiling is as high as 6 K. With the linear diffuser, the air velociry is high, and the temperature is uniform both horizontally and vertically. The air velocity generated by the vortex diffuser is moderate. The distributions of the temperature and the contaminant are rather uniform.     

Parameters affecting the frequencies of transformation and co-transformation with synthetic oligonucleotides in yeast.

Factors influencing the direct transformation of the yeast Saccharomyces cerevisiae with synthetic oligonucleotides were investigated by selecting for cyc1 transformants that contained at least partially functional iso-1-cytochrome c. Approximately 3 x 10(4) transformants, constituting 0.1% of the cells, were obtained by using 1 mg of oligonucleotide in the reaction mixture. Carrier, such as heterogeneous oligonucleotides, enhanced transformation frequencies. Transformation frequencies were dramatically reduced if the oligonucleotides had a large number of mismatches or had terminally located mismatches. Transformation with oligonucleotides, but not with linearized double-strand plasmid, was efficient in a rad52- strain, suggesting that the pathway for transformation with oligonucleotides is different from that with linearized double-strand plasmid. We describe a procedure of co-transformation with two oligonucleotides, one correcting the cyc1 defect of the target allele in the host strain, and the other producing a desired amino acid alteration elsewhere in the iso-1-cytochrome c molecule; approximately 20% of the transformants obtained by co-transformation contained these desired second alterations.     

Characterization of supported Pd-Pt catalysts by chemical probes

The temperature programmed (palladium) hydride decomposition appeared very effective method for diagnosing the extent of alloying in Pd-Pt/SiO₂ catalysts. Introduction of Pt to Pd catalysts moves the TPHD peak gradually towards lower temperatures and the shift in hydride decomposition peak is accompanied by a decrease in the amount of released hydrogen. The catalysts prepared the direct redox method showed much better alloy homogeneity than the samples prepared by coimpregnation. The results of probing with other techniques, i.e. catalytic probing with hydrodechlorination of CCl₂F₂ and XRD, were in line with TPHD data. The catalytic probing showed the presence of synergistic effect, a clear indication of Pd-Pt mixing. XRD data of post-reaction samples showed carbon incorporation into Pd-rich phase, whereas separate Pt-rich phase did not experience any bulk carbiding.     

Mapping surface temperature in large lakes with MODIS data

Satellite sensor MODIS on two platforms can produce Sea Surface Temperature over certain regions about three to four times per day. Our objective was to test if the MODIS SST product can be applied for lakes whose surface areas are large enough to be observed at the MODIS spatial resolution and to compare the satellite-derived lake surface temperatures with in situ measurements. Surface temperatures for Lakes Vänern and Vättern in Sweden, two of the largest European lakes, are extracted from the MODIS/Terra images for period 2001-2003. The results are analyzed on different quality levels, as all MODIS L2 products are equipped with an additional quality flag. We present temperature development over 2001-2003, and show the capability of the MODIS SST product to couple the known thermodynamical features in the lakes under study, where temperature varies greatly with space and time. These results can complement lake monitoring programs anywhere.     

A self-organizing fuzzy control of weld pool size in GMA welding processes

In arc welding processes, because of the complexity and nonlinearity of heat transfer phenomena, it is often difficult to design an effective control system based upon an exact mathematical model. In this paper, a self-organizing fuzzy control method is proposed to obtain a uniform weld quality by regulation of the surface temperature at a desired level. The proposed control system is designed to comprise a combined structure of the fuzzy SOC with conventional PD control for improving the system's stability. The control experiments show that the proposed controller guarantees a uniform weld quality for various welding conditions.     

电子和β射线两用外推电离室的研制

本文研制了一台测量电子束和β射线吸收剂量的外推电离室,其空腔室壁材料可拆换并分别与空气、组织和硅等效,收集电极名义直径为1.5、3、10和30mm,空气空腔可变范围为0.2～15mm。该外推电离室具有在空腔内部测温,自动改变窗口上方材料厚度及采用微型计算机控制等特点。适用于测10 MeV能量以下,剂量率为10~5～10~(-3)Gy/h的电子或β射线吸收剂量。整个外推电离室自动测剂量系统在测~(204)TLβ放射源表面剂量率的不确定度为2.3％。测1.5 MeV电子束在硅和哈密瓜深部剂量率时,不确定度分别为4.0％和2.8％。     

红外测温技术在离心复合铸造轧辊生产上的应用

本文分析了离心复合铸造轧辊生产过程中离心机停机温度和时间对轧辊质量的影响 ,提出了用先进的红外测温技术来预报停机温度和时间 ,以实现微机监控适时停机 ,保证轧辊内外层熔合良好 ;同时指出了红外测温技术在离心复合铸造轧辊生产上的应用前景     

On The Measurement of Temperature in Material Removal Processes

Because it is key to understanding the performance of material removal processes and resultant workpiece quality, the measurement of temperature during material removal is done extensively. We review several widely used temperature measurement methods and show how they can be applied to temperature monitoring during material removal. Since there is little documentation on measurement uncertainties as relates to material removal, this paper outlines the physics of each method, detailing the sources and evaluation of uncertainty. Finally, using criteria critical in measuring material removal, methods are compared, and the results presented in guide-format for participants in this field of work.     

HEAT TRANSFER IN PARTIALLY MISCIBLE TERNARY SYSTEMS

In the study of mass transfer between partially miscible liquids, temperature perturbations have been found to have an important effect in the generation of interfacial activity. Micro- and macro-generated interfacial convection usually occurs in combination with one another even in fairly simple heat or mass transfer events. These combinations are responsible for the enhancement of mass transfer rates. In an effort to acquire a better understanding of the heat transfer effects in ternary liquid-liquid systems, temperature difference profiles were measured when contacting two partially miscible phases. A vertical and a rotational transfer cell were designed to contact the partially miscible phases without inducing external disturbances. Five thermocouples were immersed in the bottom liquid phase at predetermined positions below the interface. In order to understand the influence of the convection generated, the vertical cell was designed to hinder convection in one phase, while the rotational cell permits convection in both phases. The experimental results showed larger temperature differences in the rotational cell after the contact of the phases. Also, systems which were initially unsaturated presented larger heat effects than those in which the partially miscible solvents were initially saturated. Several parameters indicating the importance of heat effects in the ternary systems studied are reported.