Experimental study on the heat transfer and flow characteristics of nanorefrigerants inside a corrugated tube

The heat transfer and flow characteristics of MWCNT-R141b nanorefrigerant with different mass fractions have been studied through experiments. Experimental results were compared with existing correlations. A two-step method was used to prepare the nanorefrigerants. Span-80 was used as surfactant with an average particle diameter of 20 nm. Transmittance method was used to evaluate the stability of nanorefrigerants. Results showed that the stability of MWCNT-R141b nanorefrigerant, which is the added dispersant, was good during the experiments. The 0.3 wt% MWCNT-R141b nanorefrigerants had optimal heat transfer enhancement effects compared with pure refrigerants. The maximum Nusselt number increased by 40%. The specific pressure drop of nanorefrigerant increased as the Reynolds number (Re) increased, and the specific pressure drop of the pure refrigerant was minimum, which is similar to R141b.     

Vapor absorption by LiBr aqueous solution in vertical smooth tubes

Heat and mass transfer in a falling film vertical in-tube absorber was studied experimentally with LiBr aqueous solution. The presented results include the effect of solution flow rate, solution subcooling and cooling water temperature on the absorption in a smooth copper tube 16.05 mm I.D. and 400 mm long. The experimental data in the previous report for a 1200-mm-long tube was also re-examined and compared. It was demonstrated by the observation of the flow in the tube that the break down of the liquid film into rivulets leads to deterioration of heat and mass transfer at lower film Reynolds number or in longer tubes. An attempt to evaluate physically acceptable heat and mass transfer coefficients that are defined with estimated temperature and concentration at the vapor–liquid interface was also presented.     

In-tube condensation of mixture of R134a and ester oil: empirical correlations

This paper presents a comparative study of the condensation heat transfer coefficients in a smooth tube when operating with pure refrigerant R134a and its mixture with lubricant Castrol “icematic sw”. The lubricant is synthetic polyol ester based oil commonly used in lubricating the compressors. Two concentrations of R134a-oil mixtures of 2% and 5% oil (by mass) were analysed for a range of saturation temperatures of refrigerant R134a between 35 °C and 45 °C. The mass flow rate of the refrigerant and the mixtures was carefully maintained at 1 g/s, with a vapour quality varying between 1.0 and 0. The effects of vapour quality, flow rate, saturation temperature and temperature difference between saturation and tube wall on the heat transfer coefficient are investigated by analysing the experimental data. The experimental results were then compared with predictions from earlier models [Int J Heat Mass Transfer (1979), 185; 6th Int Heat Transfer Congress 3 (1974) 309; Int J Refrig 18 (1995) 524; Trans ASME 120 (1998) 193]. Finally two new empirical models were developed to predict the two-phase condensation heat transfer coefficient for pure refrigerant R134a and a mixture of refrigerant R134a with Castrol “icematic sw”.     

氢压缩机管道强烈振动的消除

本文针对一往复式氢气压缩机管道振动十分强烈的情况，分析了管系的结构自振频率、气柱固有频率和气流脉动，采取了改变管系结构频率和气柱固有频率的减振措施，经实践证明获得了较为理想的减振效果。     

北满特殊钢公司φ114无缝钢管车间设计及主要设备

论述了φ１１４ｍｍ无缝钢管车间采用改进型狄塞尔轧管机的车间设计，这是继烟台鲁宝钢管厂和成都无缝钢管厂φ１７７ｍｍ车间之后重庆院设计的这种类型的无缝钢管厂。     

用φ76 mm穿孔机组生产φ63mm毛管的设备改进

介绍了用Φ76mm穿孔机组生产Φ63mm毛管的设备概况及其改进。改进后，Φ76mm穿孔机组增加了产品范围为后面的冷技工序减少了拉拔道次，从而降低了Φ51mm以下冷拔管的生产成本。     

高温对冶金窑窑体的影响

针对冶金回转窑窑体在高温下产生的失效进行数值分析，并在此基础上对冶金窑窑体的设计方法进行修正。     

平面波谱法分析电磁波在管道中的传播

通过分析电磁波从管道开口耦合进入管道的绕射机理及场在腔体内的射线特征，将进入管道的绕射场展开为平面波谱，利用平面波在自由空间的传播特性分析了电磁波沿管道的传输和反射特征。通过算例验证了该算法的有效性。     

一种悬臂式钢管喷印装置及其控制系统

本文介绍了一种用于成品钢管生产线上的悬臂式钢管喷印装置，它是一台结构和功能都较复杂的大型机电一体化设备。文中简介了它的性能、特点和工作原理，对其各部分机械装置的构成及动作以及喷印控制系统的组成和功能进行了较为深入的描述。     

焦化加热炉爆管故障分析与预防

焦化加热炉炉管内的物料通常为有杂质容易结焦的混合渣油,如果设计不合理、操作控制不当、运行周期过长等,极易造成炉管爆管事故。以2005年9月大庆石化分公司炼油厂焦化加热炉爆管故障为例,阐述了焦化加热炉的爆管原因、故障处理及预防措施,认为注水量小、渣油中含催化剂、负荷偏离设计工况、烧焦周期和烧焦速度不当等引起严重结焦是爆管的主要原因。