Iterative equalization combining algorithm in intersymbol interference channel

To realize joint optimization of spatial diversity and equalization combining in the intersymbol interference (ISI) channel, an iterative equalization combining algorithm is proposed. The proposed algorithm uses the coefficients of Turbo equalization to calculate the combination weights without estimating the signal to noise ratio in each diversity branch. The equalized symbols from different diversity branches are combined, and the extrinsic information output from the decoder is fed back to the equalizers, so as to exchange soft information between the equalizers and the decoder. The performance of the proposed algorithm is analyzed using the extrinsic information transfer (EXIT) chart and verified by simulations. Results show that our approach fully exploits time domain information from the multipath channel and spatial domain information from multi receiving antennas, which efficiently improve the performance of the receiver in the severe ISI channel.     

ACCUGRAM: A novel approach based on classification to frequency band selection for rotating machinery fault diagnosis

Frequency band selection (FBS) in rotating machinery fault diagnosis aims to recognize frequency band location including a fault transient out of a full band spectrum, and thus fault diagnosis can suppress noise influence from other frequency components. Impulsiveness and cyclostationarity have been recently recognized as two distinctive signatures of a transient. Thus, many studies have focused on developing quantification metrics of the two signatures and using them as indicators to guide FBS. However, most previous studies almost ignore another aspect of FBS, i.e. health reference, which significantly affect FBS performance. To address this issue, this paper investigates importance of a health reference and recognize it as the third critical aspect in FBS. With help of the health reference, the frequency band where the fault transient exists could be located. A novel approach based on classification is proposed to integrate all three aspects (impulsiveness, cyclostationarity, and health reference) for FBS. Classification accuracy is developed as a novel indicator to select the most sensitive frequency band for rotating machinery fault diagnosis. The proposed method (coined by accugram) has been validated on benchmark and experiment datasets. Comparison results show its effectiveness and robustness over conventional envelope analysis, the kurtogram, and the infogram.     

光照水电站装设筒形阀分析

筒形阀是一种新型的水轮机进水阀,它与球阀或蝴蝶阀相比较有防止机组飞逸事故扩大效果明显、减轻导叶全关时导水机构的快速破坏并减少漏水量,以及动水开启方便、所需时间短等优点,但对运行条件也有一定的要求。光照水电站是贵州省第1个拟采用筒形阀的电站,为此对装设筒形阀的可行性和必要性进行了认真的分析。     

涡轮搅拌桨反应器混合过程的数值计算

利用CFD方法计算单层涡轮反应器搅拌槽内流体混合过程的速度场和浓度场,研究物料在搅拌槽内的混合过程,以及不同监测点对混合时间的影响。结果表明,搅拌槽内物料的混合主要受槽内流体的流动形式所影响;混合时间的长短与监测点位置有关;在搅拌桨的桨叶附近进行监测所得到的混合时间较短,在液面附近进行监测所得的混合时间较长。在实际生产和试验中,应注意对监测点位置的选取。     

随机减量技术中周期激励的影响及消除方法

本文针对机械系统中通常存在确定性周期激励的事实 ,论证了周期干扰成分的存在对提取的随机减量特征信号的影响 ,基于数字滤波技术提出了一种从周期干扰环境中提取随机减量特征信号的简便方法。在回转机械稳定性监测中的应用实例表明本文提出的方法是有效的。     

火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。     

多载波CDMA系统中联合检测译码方法研究

为了提高多载波CDMA(MC-CDMA)系统的抗干扰能力与系统容量,提出了一种将信道参数检测与纠错码译码联合运算进行的方法,得到了一种反馈级联结构.在分析MC-CDMA系统接收性能时,通常假设信道参数能精确估计,但对于时变信道在实现上是困难的;根据本文提出的级联结构,先用导频符号进行信道参数估计,再用导频符号的译码信息作为导频符号进行信道参数的进一步优化,构成一种联合检测译码结构,能有效地降低导频符号数量,并提高了信道参数估计精度.通过仿真,与传统的方法进行了性能比较,联合检测译码方案能获得较大系统增益,是一种优化方案.     

KZON-50/120空分设备的安装调试及设计改造

在KZON-50/120空分设备的安装调试和试运行过程中,对其机械和电器部分进行了多处改造,克服了原设计中存在的不足之处。改造后,机械和电器性能更加趋于合理,操作简单,便于维护,降低了制气费用,提高了制气纯度和经济效益,保证了空分设备更加安全可靠运行。     

关于陶瓷墙地砖的深加工及其机械

本文简要回顾了陶瓷墙地砖深加工的工艺理论和机械设备。对陶瓷墙地砖深加工的自动抛光生产线和组成生产线的工艺单机作了一般介绍。指出设计陶瓷墙地砖深加工工艺单机时要注意的主要问题,并提供了解决这些问题的方法。     

直流电动机参数测定

根据直流电机的可逆原理并利用常规的实验仪表，可以简便、准确地测出直流电动机的主要参数－电磁转矩、输出转矩和效率．