Plasma-assisted CO2 reforming of methane over Ni-based catalysts: Promoting role of Ag and Sn secondary metals

Carbon dioxide (CO₂) and methane (CH₄) are the primary greenhouse gases (GHGs) that drive global climate change. CO₂ reforming of CH₄ or dry reforming of CH₄ (DRM) is used for the simultaneous conversion of CO₂ and CH₄ into syngas and higher hydrocarbons. In this study, DRM was investigated using Ag–Ni/Al₂O₃ packing and Sn–Ni/Al₂O₃ packing in a parallel plate dielectric barrier discharge (DBD) reactor. The performance of the DBD reactor was significantly enhanced when applying Ag–Ni/Al₂O₃ and Sn–Ni/Al₂O₃ due to the relatively high electrical conductivity of Ag and Sn as well as their anti-coke performances. Using Ag–Ni/Al₂O₃ consisting of 1.5 wt% Ag and 5 wt% Ni/Al₂O₃ as the catalyst in the DBD reactor, 19% CH₄ conversion, 21% CO₂ conversion, 60% H₂ selectivity, 81% CO selectivity, energy efficiency of 7.9% and 0.74% (by mole) coke formation were achieved. In addition, using Sn–Ni/Al₂O₃, consisting of 0.5 wt% Sn and 5 wt% Ni/Al₂O₃, 15% CH₄ conversion, 19% CO₂ conversion, 64% H₂ selectivity, 70% CO selectivity, energy efficiency of 6.0%, and 2.1% (by mole) coke formation were achieved. Sn enhanced the reactant conversions and energy efficiency, and resulted in a reduction in coke formation; these results are comparable to that achieved when using the noble metal Ag. The decrease in the formation of coke could be correlated to the increase in the CO selectivity of the catalyst. Good dispersion of the secondary metals on Ni was found to be an important factor for the observed increases in the catalyst surface area and catalytic activities. Furthermore, the stability of the catalytic reactions was investigated for 1800 min over the 0.5 wt% Ag-5 wt% Ni/Al₂O₃ and 0.5 wt% Sn-5 wt% Ni/Al₂O₃ catalysts. The results showed an increase in the reactant conversions with an increase in the reaction time.     

Effect of heat treatment and zircon addition on the properties of low-cement castables based on recycled alumina grog

In this investigation, low-cement castables were prepared using 70% alumina grog aggregates obtained from crushed alumina brick waste. The aggregates were thermally treated at 1550 °C for 3 h. Four types of low-cement castables were prepared with various types of aggregates (alumina grog with or without thermal treatment) and fillers (with or without zircon addition), and they were evaluated in terms of their physical, thermal, and chemical properties. Microstructural analysis via scanning electron microscopy (SEM) was performed on the castables before and after slag attack. Compared to the other fabricated castables, the thermally treated alumina grog castables with zircon showed better physical properties, such as a higher bulk density, cold crushing strength, and modulus of rupture and a lower apparent porosity and water absorption. In addition, they had a higher positive linear thermal expansion, refractoriness under load, permanent linear change, and hot modulus of rupture. The results of the SEM with energy dispersive X-ray analysis of the prepared castables confirmed that the mullite and anorthite phases were predominant when zircon was not added and the zircon–mullite phase additionally appeared upon the incorporation of zircon. A quantitative elemental analysis via X-ray fluorescence spectroscopy was employed to determine the composition of the castables. X-ray diffraction analysis showed that the alumina grog castables had a high mullite and low anorthite content, and the thermally treated alumina grog had a high anorthite, low mullite, and high zircon content. The improvement in the mechanical and thermo-mechanical properties of the castables with thermally treated alumina grog and added zircon can be attributed to the formation of the zircon–mullite phase with a low mullite phase content.     

Organic mesh template-based laminated object manufacturing to fabricate ceramics with regular micron scaled pore structures

A new aqueous slurry-based laminated object manufacturing process for porous ceramics is proposed: firstly, an organic mesh sheet is pre-paved as a pore-forming template before slurry layer scraping; secondly, the 2D pattern is built with laser outline cutting of the dried mesh–ceramic composite layer; finally, the pore structure is formed after degreasing and sintering. Alumina parts with porosities of 51.5 %, round hole diameters of 80 ± 5 μm were fabricated using 70 wt. % solid content slurry and 100 mesh nylon net. Using an organic mesh as the framework and template not only reduces the risk of damage of the green body but also ensures the regularity, uniformity and connectivity of the micron scaled pore network. The layer-by-layer drying method avoids the delamination phenomenon and improves the paving density. The new method can realize the flexible design of the pore structure by using various organic mesh templates.     

Calf massager: Intervention for body muscle discomfort during prolonged standing

Many occupations require workers to stand for long periods of time without proper interventions, which causes discomfort in the back and lower limbs. Therefore, this study aims to assess the effectiveness in alleviating body muscle discomfort during prolonged standing through the use of a calf massager. This study was conducted among male workers at a manufacturer with production line workers and the list was obtained from the HR Department and simple random sampling was done by number categorization. A total of 100 respondents (50 respondents for both the control and the experimental groups) participated in this study. The experiment took place in a room with a similar setup for the production line. Each respondent was requested to perform the simulated task for 2 hr. For the experimental group, the calf massager was turned on every 15 min. At every 15‐min interval after turning on the calf massager, respondents from both groups were required to evaluate their discomfort level on a Borg's scale CR‐10 questionnaire. The results showed that the level of body discomfort among respondents in the experimental group reduced (20–30%) compared with that of the control group. Multivariate analysis results revealed that the discomfort rating for the lower back, knees, thighs, calves, and feet was significantly lower (p < .05) among the experimental group compared with the control group. For lower body parts, the lower back region was statistically significant (p < .05) at the 90th, 105th, and 120th min; the thigh region was statistically significant (p < .05) at the 120th min; the knee region was statistically significant (p < .05) at the 105th and 120th min; the calf region was statistically significant (p < .05) at all minute intervals except the 15th and 45th min, while the feet region, was statistically significant at the 105th and 120th min. Therefore, this study indicates that calf massage treatment is capable of reducing body muscle discomfort during prolonged standing and highlights the significance of calf massage.     

Chromium evaporation and oxidation characteristics of alumina-forming austenitic stainless steels for balance of plant applications in solid oxide fuel cells

The chromium (Cr) evaporation behavior of several different types of iron (Fe)-based AFA alloys and benchmark Cr₂O₃-forming Fe-based 310 and Ni-based 625 alloys was investigated for 500 h exposures at 800 °C to 900 °C in air with 10% H₂O. The Cr evaporation rates from alumina-forming austenitic (AFA) alloys were ~5 to 35 times lower than that of the Cr₂O₃-forming alloys depending on alloy and temperature. The Cr evaporation behavior was correlated with extensive characterization of the chemistry and microstructure of the oxide scales, which also revealed a degree of quartz tube Si contamination during the test. Long-term oxidation kinetics were also assessed at 800 to 1000 °C for up to 10,000 h in air with 10% H₂O to provide further guidance for SOFC BOP component alloy selection.     

Experimental and numerical analysis of the influence of cable tray arrangements on the resulting mass loss rate and fire spreading

In the context of industrial buildings and power plants, electrical installations and cable trays represent a main fuel load and a potential initial fire source due to possible short circuits or comparable malfunction. Furthermore, a fire can spread from one tray to additional trays mounted above and/or horizontally on one tray. Because of the high significance of cable fires, several research projects have been carried out, investigating the fire behaviour of cables from small‐scale tests, eg, the cone calorimeter, up to large‐scale tests, analysing complete cable tray constructions. The goal of the work presented in this paper is the extension of the knowledge regarding the influence of geometrical parameters like the packing density and tray distance on the burning behaviour and fire spread of cable tray installations. The results are considered, together with test results from the literature, to quantify the main physical parameters describing the burning behaviour. In a next step, the general applicability of these parameters as input data for the parametrization of the source term of numerical simulations is shown. The test results show that the burning behaviour and the fire spreading highly depend on the cable arrangement of the cables on the cable tray, in combination with other boundary conditions. By applying the results as input for a fire simulation, the mass loss rate is considered appropriately.     

皮带秤秤架的响应特性曲线分析

介绍了皮带秤秤架响应特性曲线分析方法，对四种结构形式的秤架进行了响应特性曲线分析和比较，得出的结论是：悬浮式秤架的计量特性最好。     

一种大尺度二维直线度精密测量的新方法

本文提出了一种远距离、大范围二维直线度测量的新方法．该方法采用特殊设计的十字线准直激光器及线阵CCD，通过特殊的光学系统结构设计，能在0-20m距离内连续测量，直线度范围可达70mm，精度优于0．1mm，实际测量结果表明，该方法可适应野外作业环境。     

Adsp-21060的主机接口在实时图像处理中的应用

简要介绍了数字信号处理器Adsp 2 10 6 0和大规模可编程逻辑器件EP1K5 0。详细讨论了Adsp 2 10 6 0的主机接口工作模式以及一个实时图像跟踪处理器的硬件组成原理 ,在这个系统中EP1K5 0充当了主机。调试结果表明 ,所提出的硬件结构设计思想工作效率高 ,完全能够胜任实时图像处理的实际需要。