烧结机卸料装置耐磨性改善

烧结机导料箱、单辊破碎机和卸料漏斗承载着烧结热矿的导料、破碎与输送,是烧结生产的重要组成部分。高温、重载的工况环境决定着机尾卸料装置必须具有抗磨损、耐高温的特性。针对邯钢1^#435m^2烧结机机尾关键部件耐磨工作面寿命短,更换不方便等问题,分析磨损机理与失效原因,提出改进抗磨工作面结构,升级耐磨材料,优化焊接工艺等措施。通过技术方案的实施,使烧结机导料箱、单辊破碎机和卸料漏斗等卸料装置维持了较高的抗磨损性能,达到了预期的改造效果。     

Annular‐ring slot antenna designs with circular polarization radiation

The design of a microstrip‐fed annular‐ring slot antenna (ARSA) with circular polarization (CP) radiation is initially studied. To obtain CP radiation with broad 3‐dB axial ratio (AR) bandwidth that can cover the WiMAX 2.3 GHz (2305–2320 MHz, 2345–2360 MHz) and WLAN 2.4 GHz (2400–2480 MHz) bands, a novel technique of extending an inverted L‐shaped slot from the bottom section of the annular‐ring is proposed. To suppress the harmonic modes induced by the CP ARSA, the technique of integrating a defected ground structure into the annular‐ring slot is further introduced. From the measured results, 10‐dB impedance bandwidth and 3‐dB AR bandwidth of 44.86 and 9.68% were achieved by the proposed harmonic suppressed CP ARSA. Furthermore, average gain and radiation efficiency of ～4.7 dBic and 71%, respectively, were also exhibited across the bands of interest. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:337–345, 2015.     

Binary Ti–Fe system. Part I: Experimental investigation at high pressure

The present work illustrates the effect of quasi-hydrostatic pressure on the positions and widths of the homogeneity ranges of the intermetallic phases TiFe and TiFe₂ at high temperatures. The experiments were performed with Ti–Fe diffusion couples that were heat treated in a multi-anvil press at 2.5 GPa. The solubility limits of the phases were derived from the concentration profiles that were measured using electron probe microanalysis. It was found that the homogeneity ranges of TiFe and TiFe₂ extend to higher titanium concentrations, if the pressure is applied. The positions of the phase boundaries of the intermetallics on the iron-rich side are not affected by the pressure. The accuracy of the experimental data including the homogeneity ranges and temperatures was verified by comparing the homogeneity ranges of β-Ti(Fe), α/δ-Fe(Ti) and γ-Fe measured in this study with the homogeneity ranges taken from literature. The pressure was calibrated using the pressure-induced phase transitions of bismuth.     

Role of Co in formation of Ni-Ti clusters in maraging stainless steel

The effect of Co addition on the formation of Ni-Ti clusters in maraging stainless steel was studied by three dimensional atom probe (3DAP) and first-principles calculation. The cluster analysis based on the maximum separation approach showed an increase in size but a decrease in density of Ni-Ti clusters with increasing the Co content. The first-principles calculation indicated weaker Co-Ni (Co-Ti) interactions than Co-Ti (Fe-Ti) interactions, which should be the essential reason for the change of distribution characteristics of Ni-Ti clusters in bcc Fe caused by Co addition.     

High resistivity measurement of SiC wafers using different techniques

To establish fast, nondestructive, and inexpensive methods for resistivity measurements of SiC wafers, different resistivity-measurement techniques were tested for characterization of semi-insulating SiC wafers, namely, the four-point probe method with removable graphite contacts, the van der Pauw method with annealed metal and diffused contacts, the current-voltage (I-V) technique, and the contactless resistivity-measurement method. Comparison of different techniques is presented. The resistivity values of the semi-insulating SiC wafer measured using different techniques agree fairly well. As a result, application of removable graphite contacts is proposed for fast and nondestructive resistivity measurement of SiC wafers using the four-point probe method. High-temperature van der Pauw and room-temperature Hall characterization for the tested semi-insulating SiC wafer was also obtained and reported in this work.     

中小型水利施工企业推行职工持股的启示

通过广西水电南宁地质勘探基础工程处推行职工持股的思路,结合广西水利施工企业目前的具体情况, 就如何推行职工持股进行探讨,并提出建议及看法。     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

Spin probe study of semi‐interpenetrating polymer networks based on polyurethane and polymethacrylate functional prepolymers

The motional transition and heterogeneity of semi‐interpenetrating networks (SIPNs) based on polyurethane (PU) with carboxylic groups and methacrylic copolymer (PM) with tertiary amine groups were studied by the electron spin resonance (ESR) spin probe method. The concentration of functional groups in both prepolymers varied from 0 to 0.45 mmol g^?1. Spin‐probed SIPNs show that the temperature‐dependent spectra are sensitive to polymer interactions imposed by functional groups. These interactions determine the free volume distribution in the matrix and temperature at which motional transition takes place. The fraction of free volume increases with functional group concentration and reaches its maximum at 0.25 mmol g^?1. Further increases in the functional group concentration reduce the free volume. The results of the networks with strong interactions are discussed in terms of the interference of the plasticizing effect of the PU component and the formation of possible cluster cross‐links, which restricts segmental motions. Copyright © 2003 Society of Chemical Industry