Complex study of protective Cr3C2–NiAl coatings deposited by vacuum electro-spark alloying,pulsed cathodic arc evaporation,magnetron sputtering,and hybrid technology

Coatings were obtained by vacuum electro-spark alloying (VESA), pulsed cathodic arc evaporation (PCAE), magnetron sputtering (MS) techniques and VESA-PCAE-MS hybrid technology using Cr₃C₂–NiAl electrodes. The structure of the coatings was analyzed using scanning and transmission electron microscopy, X-ray diffraction and energy-dispersive spectroscopy. Mechanical properties were determined by nanoindentation, while tribological properties were assessed using pin-on-disk tribometer. Corrosion resistance was estimated by voltammetry in 1 N H₂SO₄ and 3.5%NaCl solutions. Oxidation resistance tests were performed at 800°С in air. The VESA coating had the highest thickness, low friction coefficient and high wear resistance. PCAE coating demonstrated the highest hardness (24 GPa) and elastic recovery (59%), oxidation resistance and superior corrosion resistance both in 1 N H₂SO₄ (i_corr = 70 μА/cm²) and 3.5%NaCl (i_corr = 0.74 μА/cm²) solutions. The MS coating had average mechanical properties and low corrosion current density (71 μА/cm²) in 1 N H₂SO₄. Deposition of coatings using VESA-PCAE-MS hybrid technology led to an increase in corrosion and oxidation resistance at least by 1.5 times in comparison with the VESA coating.     

一种新型回路电阻测试仪的研究与设计

针对传统低压回路电阻测试仪只能在被测设备停电时使用的一大限制,本文提出并设计了一种新型低压回路电阻测试仪。该仪器可在低压设备运行状态下对其回路电阻进行测量,在保证测量精度的前提下减少了设备停电率,大大提高了工作效率。     

A novel Ag–CuAlO2 sealant for reactive air brazing of 3YSZ and AISI 310S

Based on reactive air brazing (RAB), we designed a new type of sealant (Ag–xCuAlO₂) for joining 3 mol.% yttria-stabilized zirconia (YSZ) ceramics and AISI 310S stainless steel. The CuAlO₂ content affected the wettability of the sealant on the YSZ surface, and the joints had a high shear strength when Ag–2 wt.%CuAlO₂, which had a small contact angle on the YSZ substrate, was used as the sealant. In addition, the thickness of the oxide layer was reduced compared to that for the Ag–CuO sealant. The effects of the processing parameters on the microstructure and shear strength of the joints were investigated, and the as-brazed joints reached their highest shear strength (93.7 MPa) when brazed at 1040 °C for 30 min. After high-temperature oxidation at 800 °C for 200 h, the shear strength of the joints remained at 50 MPa, and no apparent change in the microstructure was observed, proving that the joints possessed excellent oxidation resistance.     

An automated treatment planning strategy for highly noncoplanar radiotherapy arc trajectories

Radiation therapy is a technology-driven cancer treatment modality that has experienced significant advances over the last decades, due to multidisciplinary contributions that include engineering and computing. Recent technological developments allow the use of noncoplanar volumetric modulated arc therapy (VMAT), one of the most recent photon treatment techniques, in clinical practice. In this work, an automated noncoplanar arc trajectory optimization framework designed in two modular phases is presented. First, a noncoplanar beam angle optimization algorithm is used to obtain a set of noncoplanar irradiation directions. Then, anchored in these directions, an optimization strategy is proposed to compute an optimal arc trajectory. The computational experiments considered a pool of twelve difficult head-and-neck tumor cases. It was possible to observe that, for some of these cases, the optimized noncoplanar arc trajectories led to significant treatment planning quality improvements, when compared with coplanar VMAT treatment plans. Although these experiments were done in a research environment treatment planning software (matRad), the conclusions can be of interest for a clinical setting: automated procedures can simplify the current treatment workflow, produce high-quality treatment plans, making better use of human resources and allowing for unbiased comparisons between different treatment techniques.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

仪器仪表产品脉冲耐压试验要求和保护器件的选择

仪器仪表产品的脉冲耐压试验是产品型式试验、例行试验中的基本内容。通过对GB4793.1标准的整理,归纳了仪器仪表产品的脉冲耐压试验要求。通过对试验方法和设备特性的梳理,总结了特性参数,并介绍了应对脉冲耐压试验可采取的保护器件的类别及选用方法。     

数字化蓄热式钢包烘烤器及自动控制系统

蓄热式燃烧技术和脉冲燃烧技术是新型的节能环保燃烧技术。数字化蓄热式钢包烘烤器控制系统利用数字化脉冲控制把这两项技术结合在一起。这大大降低了能耗，减少环境污染。本文针对数字化蓄热式钢包烘烤器，提出升温阶段采用自寻优算法，不断调整换向时间，并能记忆最优参数，保证经过几次烘烤后系统整体最优；保温阶段即采用脉冲控制的方法。     

二氧化碳气体保护焊在厚板上的应用

板厚为 5 5mm的 16Mn钢采用CO2 半自动气保焊建造大型转炉炉体的可能性和可靠性如何 ?目前尚缺少足够的试验数据。为了给转炉工程的施工焊接提供可靠数据 ,确保焊接质量 ,对板厚 5 5mm16Mn钢CO2 半自动的焊接性能进行了一系列的试验研究     

定径机在φ76自动轧管机组的应用

介绍了如何根据生产工艺需求对定径机进行设备改造和孔型优化设计，及定径机在φ76自动轧管机组的应用情况。     

不锈钢塔器在硫酸装置中的应用

摘 要:主要介绍Sasol Agri公司硫酸四系统的技术改造,分两步进行,第一步更换转化器、热换热器及主省煤器,生产能力由1600t/d提高到1750 t/d,且鼓风机出口压力很低。第二步更换干燥塔、二吸塔及冷换热器,连续生产能力在1950 t/d以上。使用不锈钢材质及克瓦纳·凯密迪公司专有的换热器,使装置的改造相当成功,维护及操作费用较低,并具有较大的灵活性和可操作性。