静态电子轨道衡组成部分解析及其合理选择

阐述静态电子轨道衡诸多优点;工作原理、允许误差及误差分配;轨道衡的结构组成部分、解析各部分的工作特性及技术指标要求;合理选配及推荐实例.     

结构-波浪-海床耦合系统中大圆筒结构的波压力响应

以沉入式大圆筒结构为对象，通过设计随机波浪水槽实验，测取了在单筒和连续筒两种结构型式、两种沉入深度和两种波谱输入下结构表面的动波压力分布。波面高度以及波压力历程均在领域进行分析。通过计算结构表面沿高程和沿环向的波压力谱及波压力传递函数，将单筒实测结果与基于线性绕射理论的解析解进行了比较，同时也详细对比了两种结构型式下的实测结果。文中汇报了在研究中获得的新发现及进行的相应分析，特别是在结构——波浪——海床动力相互作用下对波压力响应机理以及针对连续筒的研究，可为工程应用提供有价值的参考。     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

Equivalent Conditions for Convergence of Splittings of Non-Hermitian Indefinite Matrices

We present some sufficient and necessary conditions for convergent splitting of a non-Hermitian indefinite matrix. Some sufficient conditions to determinate a matrix with a (strongly) dominant symmetric part for a class of boundary value problem are also obtained. These results are applicable to identify the convergence of iterative methods for solving large sparse systems of linear equations.     

�¸�������в������Ȼ�����꾮�ٶȵ�;��

本文针对天然气井提高钻井速度问题,总结分析了盆地中部井身结构,水力、机械参数,聚合物钻井液,正注反挤固井等工艺技术对该地区钻速的影响。指出提高天然气井钻井速度,必须搞好系统工程,形成配套技术。     

用双向扭转圆柱组合螺旋弹簧实现扭矩测试

利用单个圆柱螺旋扭转弹簧扭转原理,给出了一种用双向扭转圆柱组合螺旋弹簧实现扭矩测试的方法。根据扭转弹簧模型,给出了预紧力、加载的证明,并对实验结果进行分析;该结构用于扭矩测试系统既实用可靠,又简单易加工;降低了测试系统的成本,具有很高的实用价值。     

改进渣浆泵过流件铸造工艺及硬度的措施

介绍了渣浆泵过流件材质的化学成分及其正交试验的优选过程，以及重新制定的铸造工艺。     

基于B/S模式的汽车零件销存管理信息系统的设计与实现

对于采用连锁经营的汽车零件销售企业来说,各经营网点分布在同一城市的不同区域或不同城市,为了在充分利用原有信息和资源的基础上处理好许多中间环节,减少人员工作量,保证企业销存状态良好,提高管理效率,设计了基于B/S模式的汽车零件销存管理信息系统的技术方案,详细讨论系统的功能设计以及实现技术。     

卸煤机走行部的技术改造

通过对卸煤机走行部的技术改造,提高了工作效率,节省了维修费用。     

关于正整数的k次根的整部

对于给定的自然数m，令口α（m)为m的是的次根的整部。即：α(m)=[m^1/k]。研究了α(m)的渐近性质，并给出了一个有趣的渐近公式。