Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.     

人工接地装置设计方法分析

本文系统地论述了人工接地装置的设计方法,修正了现有文献中有关论述的缺点和错误,提出了通过迭代求解方程组来设计人工接地装置的新方法。     

有机EL的稳定性和寿命

介绍了有机ＥＬ在稳定性及寿命方面的最新研究动态，着重描述了器件功能层组合的相互接触、阴极、空穴传输层玻璃化温度和驱动条件等对有机ＥＬ稳定性和寿命的影响。     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

一种新的纸基微流开关及其活跃方法

提出了一种新的、基于声表面波的纸基微流开关。通过软光刻技术制作内含两个微孔的聚二甲基硅氧烷(PDMS)微架,其上固定经折叠、长度可变的纸通道。PDMS微架贴附于压电基片之上,并在待连接的两微通道之下方,折叠纸通道最低端离压电基片间距为2 mm。压电基片上采用微电子工艺光刻一对叉指换能器和反射栅。当足够强度的电信号加到叉指换能器对时,激发两相向声表面波,使得压电基片上微流体输运到折叠纸通道,改变其长度,连接其上待连通的两纸基微通道,完成开关功能。对可编程微流器件提供了一种新的编程和开关控制方法。     

搅拌设备设计的几点体会

从搅拌轴的支承条件、轴承间最佳距离的确定以及搅拌轴的稳定器等几个方面讨论 ,分析了其对搅拌设备设计的影响 ,并提出了相应的措施和方法。     

橡胶模型制品胶坯精密预成型机

介绍了橡胶工业橡制品生产中胶坯制备的三种方法，其中详细介绍了精密预成型机制备胶坯。以上海德仁橡塑机械有限公司物精密预成型机为例，从结构，性能及工艺参数等方面进行了分析，说明精密预成型机是批量生产橡胶模型制品的一种得力辅助设备。     

Air-source heat pump coupled with economized vapor injection scroll compressor and ejector:Design and experimental research

Ejector can utilize high pressure energy from liquid mechanism,it can be used in heat pump system coupled with economized vapor injection(EVI)scroll compressor.When running under low temperature conditions,the performance of the EVI system with ejector can be improved further.In this paper,the design method of the heat pump system with ejector is presented,and the process for designing the heat pump with ejector(EVIe)was summarized.One prototype heat pump was designed under the condition of the evaporation ...     

液态铝合金表面张力快速检测新方法与装置

表面张力是液态合金的重要物性参数之一,铝合金表面张力与其变质处理效果及充型能力等质量参数密切相关,研究铸造铝合金表面张力快速检测方法及装置,对于开发铝合金熔炼质量炉前实时评价系统具有非常重要的实际意义.介绍了一种液态铝合金表面张力快速测试的新方法和新装置,新方法以固定时间内吹入被测液体的气泡个数以及气泡在生长过程中内部压差变化为信息参数,通过回归公式求解表面张力.基于该方法研制的表面张力新型测试装置由单片机测控单元、探头及其锁紧和升降机构、供气单元等部分构成.采用新装置可在5 s内测得铝合金表面张力,且具有较高的测试精度.