Influence of Polyalkylmethacrylate VII on Boundary Film Formation,Friction,Wear and Efficiency of Lubricants

1 Influence of PAMAon Boundary Fil mFormation and Friction1.1 Experi mental methodsUltra-thin optical interferometry has been used tostudy thinlubricating fil ms for more than a decade and theexperi mental details of this technique have been reportedpreviously[1].The principle of the test setup is shown inFigure1.A polished steel ball is loaded and rolled againstthe flat surface of a glass disc that is coated with a thinsemi-reflecting chromiumlayer and a silica spacer of about500nmthickne…     

工业管道测厚的几点问题探讨

超声波测厚在腐蚀监测上应用越来越广泛,为让这项检测技术更准确、更可靠,充分发挥功效,文章就工业管道测厚中测厚数据处理、测厚点选择、高温问题以及其它影响因素等几个方面进行了探讨。     

X60管线钢疲劳特性的研究

利用2、4和14mm的X60钢紧凑拉伸试样进行同样应力水平、固定应力比（R＝0．1）的疲劳裂纹扩展试验，揭示出高韧性管道钢的疲劳裂纹扩展存在显著的厚度效应。由于应力水平低，相应的离面应力也低，不足以导致分层开裂，因此，裂纹端部的三维应力约束随厚度增加而增大。4mm试样的疲劳裂纹速率远高于2mm试样，但厚度再增大，裂纹扩展速率不再有显著变化。进一步对表面裂纹试样进行疲劳裂纹扩展试验，并用勾线法纪录裂纹扩展情况，利用穿透裂纹的da/dN-ΔK曲线预测表面裂纹扩展，用2mm厚试样的数据控制裂纹表面长度的扩展，用14mm厚试样的数据控制裂纹底部沿厚度方面的扩展，得到了与表面裂纹扩展实验吻合很好的预测结果。     

聚合物-金属界面相形貌的研究

环氧树脂在 Al 合金表面生成纤维状的界面相结构,其形成、发展和特征与树脂的体系、交联反应条件以及 Al 合金的表面状态有关。环氧树脂的基础相为颗粒状的超结构组织。聚合物界面相的力学破坏表现为纤维体的拉伸、变形和断裂,而基础相在纯剪切受力时出现在45°方向的裂纹,并发展导致连接层的破坏。     

Investigation of the use of ram horn hydrolysate for fungal protein production

Production of the fungus Aspergillus niger NRRL 330 was studied in submerged fermentation with ram horn hydrolysate (RHH) as substrate. The characteristics of RHH have been reported previously. The RHH was enriched by addition of glucose and KH₂PO₄. The effects of kinetic parameters on the biomass yield of the fungus were investigated. The optimal conditions for growth of A niger on RHH were initial pH 6.5, temperature 30 °C, fermentation time 96 h and agitation speed 150 rpm. Under these optimal conditions the initial carbohydrate content of RHH was reduced from 1.52 to 0.2% and the biomass yield was 8.9 g l^?1. The biomass contained about 48.1% protein, 5.2% fat and 9.4% ash (on a dry weight basis). The amino acid content of the biomass was compared with Food and Agricultural Organisation (FAO) and animal feed standards. The protein produced contained all the essential amino acids for animal feed, but the amounts of these amino acids were somewhat lower than those of FAO and soybean reference protein. However, the amino acid composition of the biomass was better than that of animal feed. The results with RHH were also compared with previously reported data on fungal mycelium grown on waste liquor substrate. In conclusion, it was found that RHH could be used as a substrate in the production of fungal protein for use as animal feed. Copyright © 2003 Society of Chemical Industry     

F级高云母含量云母带的研制及应用

本文介绍了一种F级高云母含量云母带，它的主要特点是云母含量高达48％以上，具有良好的长时间耐电热老化性能，适用于高压电机主绝缘多胶模压工艺要求，该云母带的应用对提高电机绝缘水平和延长电机使用寿命具有重要意义。     

Design consideration of photocatalytic oxidation reactors using TiO2-coated foam nickels for degrading indoor gaseous formaldehyde

In the design process of the photocatalytic oxidation (PCO) reactor using TiO₂-coated foam nickels, the optimum of catalyst film thickness, light intensity and flow velocity were considered. A model was developed to study the effect of catalyst film thickness on photocatalytic degradation of formaldehyde by a TiO₂-coated foam nickel at continuous flow mode. In this model, external mass transfer and internal molecule diffusion-reaction were considered. A first-order kinetics equation was used to account for the photocatalytic reaction. Two exponential equations were employed to describe the distribution of light intensities in foam nickels and catalyst films, respectively. Validated with experimental data, the model can be used to predict the optimal thickness of catalyst films. A method for determining appropriate light intensities was proposed and discussed. The appropriate light intensity can be obtained by giving a margin, regarded as an excess coefficient, to the light intensity calculated based on the assumption of complete use of excited electron–hole pairs. The excess coefficient needs to be determined experimentally. In addition, the optimal flow velocity of PCO reactors could be consistent with the required one by changing the windward area of foam nickels. Based on the theoretical analyses, a novel PCO reactor containing 15 parallel-connected cells was designed. Each reaction cell was composed of an UV lamp and a TiO₂-coated tubular foam nickel. The performance of the reactor was tested by degrading gaseous formaldehyde at an indoor concentration level. The results showed that the reactor had low pressure loss and good degradation capability.     

Preparation of submicrometer-sized titania hollow spheres by templating sulfonated polystyrene latex particles

Submicrometer-sized titania hollow spheres with tunable shell thickness and smooth surfaces have been successfully synthesized by employing sulfonated polystyrene (PS) latex particles as a template in sol-gel method. The structure of the particles was characterized by scanning electron microscopy and transmission electron microscopy. The shell thickness was readily tuned by altering the concentration of titanium tetrabutoxide (TBOT) in ethanol solutions. The surface roughness as well as the shell thickness has the tendency to increase with the increase in the concentration of TBOT. The diameter of the hollow spheres was on the average of 20-26% smaller than the diameter of template PS latex particles. Some titania fragments were also observed for the sample with the highest TBOT concentration.     

主电机轴瓦异常情况分析解决办法

介绍南钢中板厂四辊轧机主电机轴瓦一种非典型故障现象，原因分析及解决办法，提出了对类似问题个人见解。     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).