Designed damping controller for SSSC to improve stability of a hybrid offshore wind farms considering time delay

This paper presents the stability improvement results of hybrid doubly fed induction generator (DFIG)-based and permanent magnet generator (PMG)-based offshore wind farms (OWFs) using a static synchronous series compensator (SSSC). An adaptive-network-based fuzzy inference system (ANFIS) controller of the proposed SSSC is designed to render adequate damping characteristics to the studied system. A frequency-domain approach based on a linearized system model using eigenvalue technique analysis is performed. A time-domain scheme based on a nonlinear system model subject to a three-phase short circuit fault at infinite bus with variations in the signal transmission delays has also been investigated to compare the damping of the studied system in cases of with and without controller. The simulation results with MATLAB/SIMULINK toolbox have been presented. It can be concluded from the simulation results that the proposed SSSC joined with the designed ANFIS damping controller can offer adequate damping performance to the studied hybrid DFIG-based and PMG-based OWFs under severe disturbance.     

Multi-discharge EDM coring of single crystal SiC ingot by electrostatic induction feeding method

A new technique of EDM coring of single crystal silicon carbide (SiC) ingot was proposed in this paper. Currently single crystal SiC devices are still of high cost due to the high cost of bulk crystal SiC material and the difficulty in the fabrication process of SiC. In the manufacturing process of SiC ingot/wafer, localized cracks or defects occasionally occur due to thermal or mechanical causes resulted from fabrication processes which may waste the whole piece of material. To save the part of ingot without defects and maximize the material utilization, the authors proposed EDM coring method to cut out a no defect ingot from a larger diameter ingot which has localized defects. A special experimental setup was developed for EDM coring of SiC ingot in this study and its feasibility and machining performance were investigated. Meanwhile, in order to improve the machining rate, a novel multi-discharge EDM coring method by electrostatic induction feeding was established, which can realize multiple discharges in single pulse duration. Experimental results make it clear that EDM coring of SiC ingot can be carried out stably using the developed experimental setup. Taking advantage of the newly developed multi-discharge EDM method, both the machining speed and surface integrity can be improved.     

Survey on Passivity Based Control of Induction Machine

Induction machines (IM) constitute a theoretically interesting and practically important class of nonlinear systems. They are frequently used as wind generators for their power/cost ratio. They are described by a fifth‐order nonlinear differential equation with two inputs and only three state variables available for measurement. The control task is further complicated by the fact that IM are subject to unknown (load) disturbances and the parameters can be of great uncertainty. One is then faced with the challenging problem of controlling a highly nonlinear system, with unknown time‐varying parameters, where the regulated output, besides being unmeasurable, is perturbed by an unknown additive signal. Passivity‐based control (PBC) is a well‐established structure‐preserving design methodology which has shown to be very powerful to design robust controllers for physical systems described by Euler‐Lagrange equations of motion. PBCs provide a natural procedure to "shape" the potential energy yielding controllers with a clear physical interpretation in terms of interconnection of the system with its environment and are robust vis á vis to unmodeled dissipative effects. One recent approach of PBC is the Interconnection and Damping Assignment Passivity‐Based Control (IDA‐PBC) which is a very useful technique to control nonlinear systems assigning a desired (Port‐Controlled Hamiltonian) structure to the closed‐loop. The aim of this paper is to give a survey on different PBC of IM. The originality of this work is that the author proves that the well known field oriented control of IM is a particular case of the IDA‐PBC with disturbance.     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

On the origin of strain hardening in glassy polymers

The influence of network density on the strain hardening behaviour of amorphous polymers is studied. The network density of polystyrene is altered by blending with poly(2,6-dimethyl-1,4-phenylene-oxide) and by cross-linking during polymerisation. The network density is derived from the rubber-plateau modulus determined by dynamic mechanical thermal analysis. Subsequently uniaxial compression tests are performed to obtain the intrinsic deformation behaviour and, in particular, the strain hardening modulus. At room temperature, the strain hardening modulus proves to be proportional to the network density, irrespective of the nature of the network, i.e. physical entanglements or chemical cross-links. With increasing temperature, the strain hardening modulus is observed to decrease. This decrease appears to be related to the influence of thermal mobility of the chains, determined by the distance to the glass-transition temperature (T−T_g).     

Deformation-Strength Relationships in Short-Term Tension of Heat-Resistant Materials

The analysis of 124 curves obtained in short-term tensile tests demonstrate that they can be described by varying strain hardening and softening characteristics. Different stress–strain curves can be produced at invariable yield strength and ultimate strength and interrelated proportional variations of the above characteristics. To determine some specific stress–strain curve, it is necessary to take account of yield strength and ultimate strength as well as strain corresponding to the latter. The relations between yield strength, ultimate strength and hardening and their practically complete absence between these parameters and softening were statistically established.     

时频域自动识别与压制高频噪声

本文在分析张宇等及钱忠平等提出的高频噪声判别准则基础上,利用夏洪瑞等根据在窄档等频距小波分频之后识别、压制高频噪声的思路,提出在时频域将代表地震道主要能量的几个频带的平均振幅绝对值作为正常子波的平均振幅绝对值,以此来识别和压制高频噪声的异常振幅。实际处理结果表明,此法不仅可以压制高频谐振及高频突发噪声,而且可以保护弱地震反射信号不受损害。     

小波变换在光谱特征提取方面的应用

人们在处理高光谱图像时一般要对一些典型地物进行光谱分析、特征波段的提取,以便提取出最大量的有效信息,剔除无用或冗余的信息,然后再进行分类识别.采用小波变换的分析方法,选用合适的小波进行分解,根据分解后的高频分量中包含的重要信息,利用局部相邻的正负极值点找出对应于原始光谱曲线上每个吸收带的左右边界;利用局部过零点,即可比较精确的提取出各个吸收带的中心波长.该方法比传统的光谱特征提取方法更简洁、有效,实验证明为一种比较理想的光谱特征提取方法.     

Thermodynamic and Transport Properties of Liquid HFC-227ea

The thermal conductivity and heat capacity of liquid 1,1,1,2,3,3,3-hepta-fluoropropane (HFC-227ea) have been studied by a high-frequency thermal-wave method over the temperature range of 294 to 345 K at pressures up to 2.8 MPa. The purity of the samples used throughout the measurements is 99.99 mol%. The experimental uncertainties of the thermal conductivity and heat capacity measurements were estimated to be within ±1.5 and ±2%, respectively. The thermal conductivity of HFC-227ea in the liquid phase decreases as temperature increases, while the pressure has an opposite effect.     

大功率CO2激光器脉冲电源研究

本文论述了直流高压与高频脉冲电源相叠加，构成高频、高压脉冲电源，并使其对CO2激光器进行放电实验，研究了同条件下的放电参数与功率。