Hydraulic reactivity and cement formation of baghdadite

In this study, the hydraulic reactivity and cement formation of baghdadite (Ca₃ZrSi₂O₉) was investigated. The material was synthesized by sintering a mixture of CaCO₃, SiO₂, and ZrO₂ and then mechanically activated using a planetary mill. This leads to a decrease in particle and crystallite size and a partial amorphization of baghdadite as shown by X-ray powder diffraction (XRD) and laser diffraction measurements. Baghdadite cements were formed by the addition of water at a powder to liquid ratio of 2.0 g/ml. Maximum compressive strengths were found to be ~2 MPa after 3-day setting for a 24-h ground material. Inductively coupled plasma mass spectrometry (ICP-MS) measurements showed an incongruent dissolution profile of set cements with a preferred dissolution of calcium and only marginal release of zirconium ions. Cement formation occurs under alkaline conditions, whereas the unground raw powder leads to a pH of 11.9 during setting, while prolonged grinding increased pH values to approximately 12.3.     

化妆品功效评价(Ⅵ)——化妆品人体功效评价的实验设计

概述了化妆品人体功效评价实验设计的概念、基本要素和基本原则,介绍了常用实验设计类型和实验设计要点,提供了人体功效评价实验方案设计的思路,有助于提高研究者制定实验设计方案的水平。     

Kinetic,thermodynamic parameters and in vitro digestion of tannase from Aspergillus tamarii URM 7115

Tannase is an enzyme used in various industries and produced by a large number of microorganisms. The aim of this study was to evaluate tannase production to determine the biochemical, kinetic, and thermodynamic properties and to simulate tannase in vitro digestion. The tannase-producing fungal strain was isolated from “jamun” leaves and identified as Aspergillus tamarii. Temperature at 26°C for 67?h was the best combination for maximum tannase activity (6.35-fold; initial activity in Plackett–Burman design—15.53?U/mL and average final activity in Doehlert design—98.68?U/mL). The crude extract of tannase was optimally active at 40°C, pH 5.5 and 6.5. Moreover, tannase was stimulated by Na⁺, Ca²⁺, Mg²⁺, and Mn²⁺. The half-life at 40°C lasted 247.55?min. The free energy of Gibbs, enthalpy, and entropy, at 40°C, was 81.47, 16.85, and ?0.21?kJ/mol?·?K, respectively. After total digestion, 123.95% of the original activity was retained. Results suggested that tannase from A. tamarii URM 7115 is an enzyme of interest for industrial applications, such as gallic acid production, additive for feed industry, and for beverage manufacturing, due to its catalytic and thermodynamic properties.     

构皮滩水电站泄洪洞优化设计

构皮滩水电站为满足2008年12月工程提前发电的需要,结合现有泄洪洞地质情况和施工情况对泄洪洞布置进行了专题研究,结果表明利用降低进口高程为550 m的泄洪洞和坝身放空底孔联合参与后期导流,可缓解2007年导流隧洞下闸封堵后大坝在2008年汛期施工的压力,为大坝施工增加了2个月左右的工期。     

水力射孔对套管强度的影响研究

水力射孔技术是一种新型的完井方式，深穿透水力射孔技术辅助定向水力压裂可以实现油气层改造和油气井增产。但是，水力射孔套管会在孔眼处造成应力集中，使得局部应力过大而削弱了套管和水泥环的强度，可能会影响套管的使用寿命。因此，文章利用有限元软件建立了射孔套管的三维有限元模型，分析了水力射孔后套管管体的应力分布，重点研究了水力射孔参数-孔密、孔径、孔深、射孔方位角等对套管强度的影响规律。分析结果表明，沿着最大水平地应力方向深穿透水力射孔，选择合适的孔密、孔径可将射孔对套管的损害降至最小。研究结果为提高水力射孔完井设计水平提供了一定的参数依据。     

Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.     

非稳定井流模型的半解析解

为了提高非稳定渗流计算的计算精度 ,通过数学分析得到了水位传导系数随时间变化时 ,一类非稳定渗流井流模型的半解析解 ,并进行了计算比较     

Evaluation of Atmospheric and Vacuum Residues Using Molecular Distillation and Optimization

The term atmospheric residue describes the material at the bottom of the atmospheric distillation tower having a lower boiling point limit of about 340°C; the term vacuum residue (heavy petroleum fractions) refers to the bottom of the vacuum distillation, which has an atmospheric equivalent boiling point (AEBP) above 540°C. In this work, the objective is to evaluate the behavior of different kinds of Brazilian atmospheric and vacuum residues using molecular distillation. The Falling Film Molecular Distillator was used. For the results obtained through this process, a significant range of temperature can be explored avoiding the thermal decomposition of the material. So these results are very important to the refinery decisions and improvements. The Experimental Factorial Design results showed that the temperature has more influence on the process than the feed flow rate, when a higher percentage of distillate is required.